T-mark T4-1C LTE GNSS TRACKER User Manual

June 10, 2024
T-MARK

T-mark T4-1C LTE GNSS TRACKER User Manual

Introduction

Features

  1. Fuel supply control
  2. Driving behavior analysis
  3. Multi-GNSS
  4. ACC detection
  5. Location data re-upload
  6. Smart power saving
  7. Anomaly alert (vibration, over-speed, power-off, etc.)

Operating Environment
Operating voltage: 12-90VDC
Internal backup battery: 3.7V/150mAH battery
Operating current: 50mA @12V
Standby current: 5mA @12V
Operating temperature: -20℃ to 60℃
Storage temperature: -40℃ to +85℃
Positioning accuracy: <10m
Location modes: GPS, BDS, AGPS, and LBS

Frequency Bands

Communication network LTE Cat1 + GSM
LTE-FDD B1/B2/B3/B4/B5/B7/B8/B28/B66
GSM B2/B3/B5/B8

Overview

Appearance
Appearance

Connotations of Indicators

Power Indicator (Red)
Keep on Connected to external power
Off Not connected to external power

GNSS indicator (Blue)
Fast flashing The device is searching for satellite signals.
Keep on The GNSS module is already fixed a position.
Off Device is in sleep mode or not operating

Network indicator (Green)
Fast flashing The network in searching
Slow flashing The network signal is normal
Keep on The device online
Off Device is in sleep mode or not operating

Note: By default, when the device is stationary for 3 minutes, the LED will automatically turn off and wake up after a vibration.

Installation

Inserting the SIM Card
Step 1 Prepare a proper SIM card;

Step 2 Insert the SIM.

Insert the SIM

After the SIM card is inserted, the device powers on using the backup battery. If the device fails to power on due to low battery, you can connect the device to the external power. Note: The SIM card must be inserted correctly, has GPRS services  activated, and is not in arrears. If the SIM is identified and requires a PIN, please disable the PIN request.

Installing the Device

Product wiring diagram

  1. Use a multimeter to find out the positive and negative terminals of the vehicle battery and the ACC line.
  2. Connect the red wire (positive)of the device configuration power cable to the positive terminal of the vehicle battery.
  3. Plug in the connector as shown in the figure below.

Installing the Device

CAR MOUNTING POSITION
INSTALLATION

ELECTRIC CAR INSTALLATION LOCATION
INSTALLATION

MOTORCYCLE INSTALLATION POSITION
INSTALLATION

Product Features

Content Function Description
**** Positioning function 4G all-
network Support 4G network, efficient transmission, faster and more accurate.
**** Timed tracking Transmit back the positioning informationsuch as

latitude and longitude according to the set interval time.
Street map| 360 degree high-definition map
Speeding alarm| When driving over speed, the locator will send alarm to your cell phone
Vibration alarm| Built-in vibration sensor, continuousvibration of the vehicle, the device will immediately send alarm alerts
Electronic fence| When the car driving range exceeds thespecified area, the platform will send alarm information
History track| Can play back 90 days of the track, playback the speed, direction, stay time and othercontent
Displacement alarm| When the vehicle encounters illegaloperation or theft, the fuel and electricity canbe cut off remotely by computer or cell phone APP
Fleetmanagement| 1 cell phone can manage multiple devices, or 1 device multiple cell phone management

Analysis of common problems

Failure phenomenon Failure analysis Treatment method
**** Blue light flashes slowly Determine whether to

use the terminal in areas with poor GPS signals, such as near tall buildings orunderground parking lots| **** Move the vehicle to a location with a good signal Use the terminal
Determine whether the front windshield of the vehicle has metal heat insulation film affecting the signal reception| If there is a film, the equipment will be changed to other vehicles to test whether the blue light is always on, such as in other vehicles without film to test no problem, then the vehicle iscaused by the film
Determine whether there is a shield or signal jammer on or around the car| If there is a shield or source of interference, remove the shield or source of interference and try toreinstall
Blue lightflashing fast| Chip failure| Return to factory for repair
**** Yellow light is flashing fast| Determine whether the SIMcard is installed properly| Check whether the SIM card isinstalled in place
Determine if there is dirt or poor contact on the metalsurface of the SIM card| Wipe the metal chip surface with a clean cloth or repeatedly insert andremove the card several times
**** The yellow light flashes slowly.| Determine if the vehicle is in a place with no mobile network, such as anunderground parking lot.| Please drive the vehicle to a place with good network signal and try to reinstall it.
Determine whether theserver background is normal| Ask if the server of the backgroundmanagement platform is normal
Determine whether the SIM card status is normal or not| Check whether the status of the SIM card is normal through the SIM cardinquiry platform
Determine whether there is a shield or signal interferer on the car or around| If there is a shield or source of interference, remove the shield or source of interference and try toreinstall

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals