renkforce 2584537 FDM Pro 7 Dual 3D Printer User Guide

: June 10, 2024
: renkforce

Table of Contents

renkforce 2584537 FDM Pro 7 Dual 3D Printer
Product Features
Setting up the equipment
Build Platform Calibration
Install the Printing Filament
Starting the printing process
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

renkforce 2584537 FDM Pro 7 Dual 3D Printer

Product Information: FDM 3D printer Pro 7 Dual

The FDM 3D printer Pro 7 Dual is an advanced 3D printer that allows you to print two different filaments at the same time. With its large build volume and high printing accuracy, this printer is perfect for professional use.

Features:

Dual extruder system
Large build volume
High printing accuracy
Easy-to-use interface
Compatible with most 3D printing software

Product Usage Instructions:

Before using the FDM 3D printer Pro 7 Dual, please read the safety instructions provided with the product.

Setting up the equipment:

Remove the 6 belt buckles and take out the pearl cotton on the platform.
Turn on the power and raise the build platform then take out the pearl cotton.
Put on the metal build platform and magnetic mat.
Install the left spool holder and rotate it clockwise.
Install the right spool holder and rotate it clockwise.
Press the tube connector and insert the filament tube.

Build Platform Calibration:

The build platform has been calibrated and well-leveled when out of the factory, but some deviation will occur during transportation. So, you’d better level the platform before printing.

Click Tool-Preheat and heat the platform to the preset temperature.
Click Leveling and put an A4 paper between the nozzle and platform.
Click Point 1 (as the photo above). The print head E1 moves to the front left, do the levelling.
Click Point 2. The print head E1 moves to the front right, do the levelling.
Click Point 3. The print head E1 moves to the rear right, do the levelling.
Click Point 4. The print head E1 moves to the rear left, do the levelling.
If the A4 paper can be slid easily, it means the distance between the nozzle and platform is too far. You can turn the knob anticlockwise until the paper can be slid with slight resistance.
If the paper can’t be moved, you can turn the knob clockwise until the paper can be slid with slight resistance.
After calibrating extruder E1, click E2 Calibration. The print head moves to the right front of the platform.

Starting the printing process

Install the filament on the left side and right side.
Click Tool-Preheat and heat the nozzle to the preset temperature.
Feeding the filaments into E1 and E2 extruders.
Click Extrusion1 and heat the nozzle to the preset temperature.
Click Printing and choose the printing file.
Click ReadyPrint…Confirm to start the printing process.

Product Features

Dimension 630 x 430 x 625 mm
Print various materials: PLA,ABS,PETG,PC,PA,PP,HIPS,PVA etc.
Max. size of the printed object
- Single Head/Dual Color Mode 360 x 250 x 200mm
- Twins/Mirror Mode 140 x 250 x 200mm
Printed layer thickness 0.05 – 0.3 mm
Print speed 20 – 200 mm/s
Colour touch screen display
Operating voltage: 100 – 240 V/AC, 50/60 Hz
Nozzle size 0.4/0.6/0.8 mm

Read the safety instructions supplied with the product before using

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represents the technical status at the time of printing.
Copyright 2023 by Conrad Electronic SE. *2584537_V2_0223_02_qsgen(2)

Setting up the equipment

Remove the 6 belt buckles, and take out the pearl cotton on the platform.
Turn on the power; raise the build platform then take out the pearl cotton
Put on the metal build platform and magnetic mat.
Install the left spool holder; Rotate it clockwise
Install the right spool holder; Rotate it clockwise
Press the tube connector and insert the filament tube

Build Platform Calibration

The build platform has been calibrated and well levelled when out of the factory, but some deviation will occur during the transportation. So you’d better level the platform before the printing.

Put on the metal build platform and magnetic mat.
Click “Tool”-“Preheat”
Click “HeatBed”; heat the platform to the preset temperature.
Click “Leveling”; Put an A4 paper between the nozzle and platform.
Click ”Point 1” (as the photo above); The print head E1 moves to the front left, do the leveling. Click ”Point 2” (as the photo above); The print head E1 moves to the front right, do the leveling. Click ”Point 3” (as the photo above); The print head E1 moves to the rear right, do the leveling. Click ”Point 4” (as the photo above); The print head E1 moves to the rear left, do the leveling.
If the A4 paper can be slid easily, it means the distance between the nozzle and platform is too far; you can turn the knob anticlockwise until the paper can be slid with slight resistance.
If the paper can’t be moved, you can turn the knob clockwise until the paper can be slid with slight resistance.
After calibrating the extruder E1, Click “E2 Calibration”, The print head moves to the right front of the platform.
Loosen the screws of E2 heat sink,put one A4 paper between the nozzle and nozzle, calibrate the nozzle and heat block unit up and down till there is slight resistance.

Install the Printing Filament

Install the filament on Left side and Right side.
Feeding the filaments into E1 and E2 extruders.
Click “Tool”-“Preheat”
Click “ Extrusion1”; heat the nozzle to the preset temperature.
Return and click “Extrusion”
Click “In”; The filament comes out from the nozzle, the loading is finished.
Click “Extrusion 2” then Click “Extrusion 2” and preheat the Extrusion 2.
Wait for the print head E2 to reach the preset temperature, then Click “In”

Starting the printing process

Click “Printing” and choose the printing file.
Click “ Confirm” and choose the printing mode as same as you sliced.
When the printing is done, the user can take out the magnet mate until it cools down, and remove the finished prints with your hand, no any tools or scrapper needed.