dji RC Motion 2 Powerful and Intuitive Motion Controller User Guide

dji RC Motion 2 Powerful and Intuitive Motion Controller

Product Information: DJI RC Motion 2

The DJI RC Motion 2 is a remote control designed for use with DJI drones. It features intuitive controls and a range of advanced features, including takeoff and landing controls, joystick controls for altitude and horizontal movement, mode switching, and camera controls.

Key Features

• Lock Button Takeoff
• Landing Button
• Brake Button
• Joystick Toggle for Altitude and Horizontal Movement
• Mode Switching Button
• FN Dial for Camera Control

In the box

• DJI RC Motion 2 Remote Control
• Instruction Manual

Product Usage Instructions: DJI RC Motion 2

The DJI RC Motion 2 is designed to work with DJI drones. Follow the steps below to get started:

1. Check the battery level of your remote control by pressing the power button once.

2. To power on/off the remote control, press the power button and then press and hold it.

3. Power on your drone and goggles, and ensure that the drone is linked with the goggles.

4. Link the remote control with the drone by following the steps below:

   • Press and hold the power button of the drone until the battery level indicators blink in sequence.
   • Press and hold the power button of the remote control until it beeps continually and the battery level indicators blink in sequence.
   • The remote control will stop beeping when linking is successful, and the battery level indicators will turn solid and display the battery level.

5. Use the lock button to take off the drone by pressing it twice.
   Hold it down to make the drone ascend to approximately 1.2m and hover. Press and hold the button while hovering to land the drone and stop the motors.

6. Use the joystick toggle to move the drone up or down or horizontally left or right.

7. Use the mode button to switch between Normal and Sport mode.
   Press and hold the button to initiate RTH (Return-to-Home).

8. Use the FN dial to control the camera tilt. Press the dial to open the camera settings panel in the FPV view of the goggles. Scroll the dial to navigate the settings menu or adjust the parameter value, then press the dial to confirm the selection.
   Press and hold the dial to exit the current menu. Use the FN dial to control the camera tilt before takeoff or during RTH and landing. Press and hold the FN dial from the FPV view and then scroll up or down to tilt the camera. Release the dial to stop the camera tilt.

Following these instructions will allow you to use your DJI RC Motion 2 remote control with your DJI drone.

Instructions

1. Check battery level: press once Power n/off: press then press and hold.

2. Power on the aircraft and the goggles. Make sure that the aircraft has linked with the goggles.

3. 

4. Press and hold the power button of the aircraft until the battery level indicators blink in sequence.

5. Press and hold the power button of the controller until it beeps continually and the battery level indicators blink in sequence

6. The controller stops beeping when linking is successful and the battery level indicators turn solid and display the battery level.

7. 1. Lock Button
      Takeoff: press twice to start the aircraft motors and then press and hold to make the aircraft take off. The aircraft will ascend to approximately 1.2 m and hover. Landing: while the aircraft is hovering, press and hold to land the aircraft and stop the motors. Brake: press during flight to make the aircraft brake and hoverin place. Press again to unlock the attitude.

8. Joystick Toggle
   up or down to make the aircraft ascend or descend. Toggle left or right to make the aircraft horizontally move left or right.

9. Mode Button
   Press to switch between Normal and Sport mode. Press and hold to initiate RTH.

10. FN Dial
    Press the dial to open the camera settings panel in the FPV view of the goggles. Scroll the dial to navigate the settings menu or adjust the parameter value, then press the dial to confirm the selection. Press and hold the dial to exit the current menu. Use the FN dial to control the camera tilt before takeoff or during RTH and landing. Press and hold the FN dial from the FPV view and then scroll up or down to tilt the camera. Release the dial to stop the camera tilt.

11. Shutter/Record Button
    Press once: take a photo or start/stop recording. Press and hold: switch between the photo and video modes.

12. Accelerator
    Press to fly the aircraft in the direction of the circle in the goggles. Push forward to fly the aircraft backward. Apply more pressure to accelerate. Release to stop and hover.

How To Use

CHARGING

Activation

When all devices are powered on and linked, connect the USB-C port of the goggles to the mobile device and run the DJI Fy app. The app will automatically identify the DJI RC Motion 2 and activate it in silent mode. Activate the device as soon as possible after purchase to avoid affecting the after-sales service.

Disclaimer

By using this product, you signify that you have read, understand, and accept the terms and conditions of this guideline and all instructions at
https://www.dji.com/rc-motion-2. EXCEPT AS EXPRESSLY PROVIDED IN AFTER-SALES SERVICE POLICIES AVAILABLE AT (http://www.DJI.COM/SERVICE), THE PRODUCT AND ALL MATERIALS AND CONTENT AVAILABLE THROUGH THE PRODUCT ARE PROVIDED “AS IS” AND ON “AS AVAILABLE BASIS” WITHOUT WARRANTY OR CONDITION OF ANY KIND. This product is not intended for children.

Specifications

• Model Number RM220

• Weight Approx. 170 g

• Operating Temperature -10° to 40°C(14° to 104° F)

•  Operating Frequencyy 2.4000-2.4835 GHz
  5.725-5.850 GHz (not available in some countries or regions)

• Transmitter Power (EIRP)  2.4 GHz: <30 dBm (FCcC), <20 dBm (CE/SRRC/MIC)
  5.8 GHz: <30 dBm (FCO, <23 dBm (SRRC), <14 dBm (CE)

Compliance Information

FCC Compliance Notice
Supplier’s Declaration of Conformity
Product name: DJI RC Motion 2
Model Number: RM220
Responsible Party: D rechnology. Inc
Responsible Party Address : 201 S. Victory Blvd., Burbank, CA 91502
Website: www.di.com

We, DJI Technology, Inc., being the responsible party, declares that the above mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• (1) This device may not cause harmful interference, and
• (2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in aCCordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF EXposure Information
This remote controller device complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 4 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the limbs.

ISED Compliance Notice CAN ICES-003 (B)/ NMB-003(B)
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

• (1)This device may not cause interference.
• (2)This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with RSS 102 radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter, The portable device is designed to meet the requirements for expoure to radio waves established by the ISED.
These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

EU Compliance Statement: Sz DJI TECHNOLOGY CO., LTD. hereby declares that this device (DJI RC Motion 2) is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU. A copy of the EU Declaration of Conformity is available online at
www.dji.com/euro-compliance EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany
GB Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (DJI RC Motion 2) is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017. A COpy of the GB Dedlaration of Conformity is available online at www.dji.com/euro- compliance

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

Environmentally friendly disposal

Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.https://s.dji.com/guide53
DJI is a trademark of DJI.
Copyright© 2023 DJI All Rights Reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>