LIGHT BRICKS 10291 Queer Eye The Fab 5 Loft Installation Guide

June 10, 2024
LIGHT BRICKS

LIGHT BRICKS 10291 Queer Eye The Fab 5 Loft

LIGHT-BRICKS -Queer-Eye-The-Fab-5-Loft-PRODUCT-IMAGE

Light My Bricks Installation Guide

The Light My Bricks installation guide is designed to help youbinstall the LEGO Queer Eye The Fab 5 Loft 10291 light kit. Before you begin, please make sure you have read and understood all the instructions.

Package Contents

  • 8x White 30cm Bit Light
  • 1x Warm 30cm Large Bit Light
  • 3x White Strip Light
  • 2x 6-Port Expansion Board
  • 1x 2-Port Expansion Board
  • 1x Dimmer Control Board 2PDIM V1
  • 6x Adhesive Squares
  • 3x 5cm Connecting Cable
  • 3x 15cm Connecting Cable
  • 1x USB Power Cable (Power Source not Included)

Instructions

Before You Begin

Please note that laying cables in between and underneath bricks can be tricky. Take your time and be careful not to damage any of the bricks or lights.

Connecting Cable Connectors To Expansion Boards

When inserting connectors to ports on expansion boards, make sure to insert them gently and correctly to avoid damaging the plugor connector.

Connecting Cable Connectors To Strip Lights

Ensure that you insert the connectors to ports on strip lights correctly. Connectors can only be inserted one way. With the strip light facing up, ensure the side of the connector with the wires exposed is facing down. Do not force a plug into a port connector as doing so will result in damage to the plug and connector.

Connecting Micro Cable Connectors To Micro Expansion Board Ports

Take extra care when inserting micro connectors to micro ports of micro expansion boards. The process is similar to connecting lights and cables to strip lights. With the expansion board facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, do not force it. Use your fingernail to push the plastic part of the connector to the micro port.

Blueprint

Refer to the blueprint for guidance on where to place the lights.

Instructions

Follow each step carefully to ensure a smooth installation of your light kit. If you have any problems, please refer to the online troubleshooting guide.

Legend
  • DISCONNECT: Remove the connector from the port.
  • CONNECT / RECONNECT: Insert or reinsert the connector into the port.
  • TURN / FLIP: Rotate or flip the light to a different angle.
  • DIRECTIONAL: Change the direction of the light beam.
  • TWIST / BRAID: Twist or braid cables together.
  • POWER ON TEST: Turn on the power to test the lights.

Follow the legend symbols for each step carefully to install the lights correctly.

Final Product

Your final product should be a beautifully lit LEGO Queer Eye The Fab 5 Loft 10291 model. Enjoy your new creation!

Troubleshooting

If you encounter any problems during the installation process, check the online troubleshooting guide for assistance.

Contact

If you still have questions or concerns about your Light My Bricks installation, contact our customer support team for assistance.

Light My Bricks
LEGO® QUEER EYE THE FAB 5 LOFT 10291 INSTALLATION GUIDE

Hi There!
We’re here to help you get started on the LEGO® Queer Eye The Fab 5 Loft (10291) Light Kit.
This PDF details the instructions for the LED light kit only.
If you run into any issues, please refer to the troubleshoot-ing section towards the end of this guide.
Have fun and enjoy!
INSTALLATION GUIDE

LIGHT-BRICKS -Queer-Eye-The-Fab-5-Loft-1

PACKAGE CONTENTS:

  • 8x White 30cm Bit Light

  • 1x Warm 30cm Large Bit Light

  • 3x White Strip Light

  • 2x 6-Port Expansion Board

  • 1x 2-Port Expansion Board

  • 1x Dimmer Control Board 2PDIM V1

  • 6x Adhesive Squares

  • 3x 5cm Connecting Cable

  • 3x 15cm Connecting Cable

  • 1x USB Power Cable (Power Source not Included)

ASSORTED BRICKS:

  • 1x Plate 1×2 – Trans Clear
  • 1x Plate 1×1 – Trans Clear
  • 1x Tile 1×2 – Dark Grey
  • 1x Tile 1×1 – Dark Grey
  • 6x Round Plate 1×1 Open Stud – Black
  • 5x Arm Skeleton, Bent with Clips (Horizontal Grip) – Black
  • 10x Plate 1×1 Mod Rounded w Handle – Black

Before You Begin

Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead ensure they are laying comfortably in between each stud.

CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.

Connecting Cable Connectors To Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can re-sult in bent pins inside the port or possible overheating of the expansion board when connected.

Connecting Cable Connectors To Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.

Connecting Micro Cable Connectors To Micro Expansion Board Ports
Take extra care when inserting the micro connectors to micro ports of Micro Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is similar to connecting lights and cables to Strip Lights. With the expansion board facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, do not force it. Use your fingernail to push the plastic part of the connector to the micro port.

Installing Bit Lights Under Lego® Bricks And Plates
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.LIGHT-MY-BRICKS-75349-Lego-
Star-Wars-Captain-Rex-Helmet-Light-Kit-9

BLUEPRINT

LIGHT-BRICKS -Queer-Eye-The-Fab-5-Loft-6

INSTRUCTIONS

To ensure a smooth installation of your light kit, please read and follow each step carefully. If you run into any issues, please refer to the online troubleshooting guide.

LEGEND:

  • DISCONNECT CONNECT / RECONNECT TURN / FLIP DIRECTIONAL TWIST / BRAID LIGHT-MY-BRICKS-75350-Lego-Star-Wars-Clone-Commander-Cody-Helmet-15 POWER ON / TEST

LIGHT-BRICKS -Queer-Eye-The-Fab-5-Loft-7

LIGHT-BRICKS -Queer-Eye-The-Fab-5-Loft-8

LIGHT-BRICKS -Queer-Eye-The-Fab-5-Loft-9

LIGHT-BRICKS -Queer-Eye-The-Fab-5-Loft-10

Make 4 more spotlights to use for later in the kit

Grab either of the Bit Lights from the neon sign step

Connect the Bit Light Cable from the spotlight in step 4 to the 2-Port Expansion Board
Grab the cable from the Bit Light used in the neon sign

If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues in our troubleshooting section.

Ensure the Dimmer Control Board arrow on the knob is pointing in this direction to get the right brightness
Connect the other end to a USB Power Bank, USB Wall Adaptor, or USB to AA Battery Pack (sold separately)

If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues in our troubleshooting section.

Grab the cable from the spotlight you just installed

Grab the single Bit Light and move it out of the way
The left cable is the USB and the other is the kitchen lights from the wall

Grab the cable from the first installed spotlight
Grab the cable for the next spotlight and pull up the wall

Grab the remaining loose cable down the wall
Grab the loose Bit Light from before

If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues in our troubleshooting section.
Connect the other end to a USB Power Bank or Adapter to complete installation of your light kit

FINAL PRODUCT

This finally completes installation of the Light My Bricks Queer Eye The Fab 5 Loft 10291 Light Kit.

TROUBLESHOOTING Guide

  • Light My Bricks lighting kits contain individual components that are very small and can be easily damaged if not handled correctly.
  • To prevent unnecessary damage to components, we highly recommend that the User Guide section, “Important things to note” is read carefully. Follow the handling procedures in the User Guide to help prevent faults and damages to your Light My Bricks components.
  • If you are experiencing issues with your Light My Bricks set, watch our troubleshooting video or read on for a list of common causes to help you troubleshoot.
  • Firstly, ensure that the batteries have power using a battery charge gauge.
  • If the batteries have no power, replace the batteries. If the batteries still have power, check to see if the batteries have been inserted correctly into the battery pack.

Check For CR2032 Batteries Using The Flat Battery Pack
Inside the battery pack is a symbol indicating which side the (round) CR2032 battery should be inserted. Check that the “+” side of the battery pack has
the battery with the “+” symbol facing downwards.
On the opposite side, the “-” side of the battery pack should have the battery flipped upside down, that is the “+” symbol facing upwards

Check For Cr2032 Batteries Using The Round Battery Pack
Inside the battery pack is a symbol indicating which side the (round) CR2032 battery should be inserted. In this case, for the stacked battery pack, ensure that BOTH batteries have the “+” symbol facing upwards.

Check for AA batteries using the AA battery pack
Inside the battery pack are symbols indicating which direction the AA battery should be inserted. The flat side of the battery should be paired with the spring side of the battery pack.
If the batteries have been installed correctly and your kit still isn’t operating correctly, the next step is to check the wiring.

Check Your Wires
In order for Light My Bricks components to fit in between and underneath LEGO® bricks, the components need to be very small. Due to this nature, Light My Bricks components can be easily damaged when not handled correctly.
Be careful when removing unpacked components out of the packaging and ensure not to forcibly pull at the wires as this can damage the soldering that attach the wires to the LEDs.
If the wiring is detached from the LED itself, the light will not operate.
When connecting lights to your LEGO® set, check that there are no pinched wires underneath or in between bricks and plates. When the wires are pinched and the exposed wires are touching each other, this can cause a crosswire and the lights to not function correctly.

Check Your Expansion Board Ports/ Strip Light Ports / Effects Board Ports
It is important to note that connectors can only be inserted to the expansion board, strip light, or effects board ports in one direction. Forcibly inserting connectors in the incorrect direction will result in damaging the pins inside each of the ports on your component board. Not only will a light connected to the damaged port not work, but if the pins inside the port are bent to a point they are touching each other, this can result in all other lights in the system to stop working. This is a short circuit.

A short circuit can also result in overheating of the board, cable or batteries. If you suspect a short circuit, DISCONNECT POWER IMMEDIATELY Batteries can fail, catch fire, or even explode if left connected to a short circuit for too long. If you suspect you have a faulty component due to a bent pin, try the following steps: If you look carefully inside each of the ports, each port contains 2 small pins that should be straight. You will be able to identify a faulty port if it has any bent pins.

LIGHT-MY-BRICKS-75349-Lego-Star-Wars-Captain-Rex-Helmet-Light-
Kit-31

CONTACT US

If you have an enquiry regarding the online shop, our products or a general enquiry please refer to our Frequently Asked Questions webpage. Alternatively, you can contact our Customer Services team by visiting our online support portal.
support.lightmybrick.com
We thank you for purchasing this product and hope you enjoy!

lightmybricks.com

© 2022 Light My Bricks Pty Ltd – Head Office: 4/26 Rushdale Street, Knoxfield VIC 3180, Australia. Phone: +61 420 643 543 | All Rights Reserved | Light My Bricks™ sell LED lighting kits only. All LEGO® sets featured in images are sold separately. Light My Bricks™ and the Light My Bricks logo, are trademarks and copyrights of Light My Bricks Pty Ltd. LEGO® is a trademark of the LEGO® Group of Companies which does not sponsor, authorize, or endorse this document.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

LIGHT BRICKS User Manuals

Related Manuals