Nikon AF-S NIKKOR 70-200mm F-2.8E FL ED VR Lens User Manual

: June 5, 2024
: Nikon

Table of Contents

Nikon AF-S NIKKOR 70-200mm F-2.8E FL ED VR Lens User Manual
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Nikon AF-S NIKKOR 70-200mm F-2.8E FL ED VR Lens User Manual

Printed in Japan
SB6G01 (7C)
7MA0377C-07

Nikon Corporation

Before using this product, please carefully read both these instructions and the camera manual.

Note: This lens does not support D2- or D1-series, D200, D100, D90, D80, D70-series, D60, D50, D40-series, or D3000 digital SR cameras or film SIR cameras.

For Your Safety

To prevent damage to property or injury to yourself or to others, read “For Your Safety” in its entirety before using this product.

Keep these safety instructions where all those who use this product will read them.

WARNING: Failure to observe the precautions marked with this icon could result in death or severe injury.

CAUTION: Failure to observe the precautions marked with this icon could result in injury or property damage.

WARNING

Do not disassemble or modify this product.
Do not touch internal parts that become exposed as the result of a fall or other accident.
Failure to observe these precautions could result in electric shock or other injury.
Should you notice any abnormalities such as the product producing smoke, heat, or unusual odors, immediately disconnect the camera power source.
Continued operation could result in fire, burns or other injury.
Keep dry.
Do not handle with wet hands.
Failure to observe these precautions could result in fire or electric shock.
Do not use this product in the presence of flammable dust or gas such as propane, gasoline or aerosols.
Failure to observe this precaution could result in explosion or fire.
Do not directly view the sun or other bright light source through the lens or camera.
Failure to observe this precaution could result in visual impairment.
Keep this product out of reach of children.
Failure to observe this precaution could result in injury or product malfunction.
In addition, note that small parts constitute a choking hazard. Should a child swallow any part of this product, seek immediate medical attention.
Do not handle with bare hands in locations exposed to extremely high or low temperatures.
Failure to observe this precaution could result in burns or frostbite.

CAUTION

Do not leave the lens pointed at the sun or other strong light sources.
Light focused by the lens is a source of fire and damage to the product’s internal parts.
Do not leave the product where it will be exposed to extremely high temperatures, for an extended period such as in an enclosed automobile or in direct sunlight.
Failure to observe this precaution could result in fire or product malfunction.

Notice for customers in Canada

CAN ICES-3 B/ NMB-3 B

Parts of the Lens (Figure 1)

Lens hood mounting mark
Rubber grip
Zoom ring
Focal length scale
Focal length mark
Focus function buttons (focus lock/AF start)
Focus ring
Focus distance indicator
Focus distance mark
Lens rotation index
Tripod collar ring rotation index
Tripod collar ring rotation index (90%)
Lens mounting mark
Rubber lens-mount gasket
CPU contacts
Focus-mode switch
Focus limit switch
Vibration reduction switch
Focus function selector (AF-L/OFF/AF-ON)
Lens rotation index (90%)
Tripod collar ring fastening screw
Tripod collar ring
Tripod collar mounting foot
Lens hood
Lens hood lock mark
Lens hood lock release button
Lens hood alignment mark
Tripod collar lock release
Tripod collar lock screw
Tripod collar

Focus

Supported focus modes are shown in the following table (for information on camera focus modes, see the camera manual)

Focus

A/M and M/A Modes

M/A : Autofocus can be over-ridden by rotating the lens focus ring.
A/M : As above, except that the focus ring must be rotated farther before the autofocus is over-ridden, preventing accidental changes to focus caused by unintended operation of the focus ring.

Slide the lens focus-mode switch to AIM or MIA.
Focus.
If desired, autofocus can be over-ridden by rotating the lens focus ring while the shutter-release button is pressed halfway {or, if the camera is equipped with an AF-ON button. while the AF-ON button is pressed, or if the focus function selector is set to AF-ON , while pressing a focus function button}. To refocus using autofocus, press the shutter-release button halfway or press the AF-ON or focus function button again.

The Focus Limit Switch

This switch determines the focus distance limits for autofocus.

FULL : Select this option to use the entire focus range.
∞-5 m : If your subject will always be at distance of at least 5 m (16.5 ft), select this option for faster focusing.

The Focus Function Buttons and Selector

The function assigned to the focus function buttons can be selected using the focus function selector.

The focus function Buttons and Selector

The assigned function can be performed by pressing any of the four function buttons.

Focus Lock (AF-L)

Focus lock is only available with autofocus.

Slide the lens focus-mode switch to A/M or M/A.
Slide the focus function selector to AF-L.
Lock focus.
Focus can be locked by pressing any of the focus function buttons and remains locked while the button is pressed. Focus can also be locked using camera controls.

Lens AF Start (AF-ON)

Slide the lens focus-mode switch to A/M or M/A.
Slide the focus function selector to AF-ON.
Focus.
Press any of the focus function buttons to focus using autofocus.
You can also focus using camera controls.

Zoom

Before focusing, rotate the zoom ring to adjust the focal length and frame the photograph.

Depth of Field

Depth of field can be previewed using the camera’s depth-of-field preview feature.
Note that the focus distance indicator is intended only as a guide and may not accurately show the distance to the subject and may, due to depth of field or other factors, not show ∞ when the camera is focused on a distant object.

Aperture

Aperture is adjusted using camera controls. The frame rate may drop at some apertures.

Built-in Flash Units

When using the built-in flash on cameras equipped with a built-in flash unit, remove the lens hood to prevent vignetting (shadows created where the end of the lens blocks the light from the built-in flash).

Vibration Reduction (VR)

Vibration reduction (VR) reduces blur caused by camera shake, allowing shutter speeds up to 4.0 stops slower than would otherwise be the case, increasing the range of shutter speeds available. The effects of VR on shutter speed are measured in NORMAL mode according to C amera and I maging P roducts A ssociation (CIPA) standards; FX-format lenses are measured using FX-format digital cameras, DX-format lenses using DX-format cameras. Zoom lenses are measured at maximum zoom.

Using the Vibration Reduction Switch

Select OFF to turn vibration reduction off.
Select NORMAL for enhanced vibration reduction when photographing stationary subjects. Vibration reduction takes effect when the shutter-release button is pressed halfway.
Select SPORT for photographing athletes and other subjects that are moving rapidly and unpredictably. Vibration reduction takes effect when the shutter-release button is pressed halfway.

Using Vibration Reduction: Notes

When using vibration reduction, press the shutter-release button halfway and wait for the image in the viewfinder to stabilize before pressing the shutter-release button the rest of the way down.
When vibration reduction is active, the image in the viewfinder may jiggle after the shutter is released. This does not indicate a malfunction.
SPORT is recommended for panning shots, although NORMAL is also supported.
In NORMAL and SPORT modes, vibration reduction applies only to motion that is not part of a pan (if the camera is panned horizontally, for example, vibration reduction will be applied only to vertical shake).
Do not turn the camera off or remove the lens while vibration reduction is in effect. If power to the lens is cut while vibration reduction is on, the lens may rattle when shaken. This is not a malfunction, and can be corrected by reattaching the lens and turning the camera on.
If the camera is equipped with a built-in flash, vibration reduction will be disabled while the flash charges.
NORMAL and SPORT vibration reduction can reduce blur when the camera is mounted on a tripod. OFF may however produce better results in some cases depending on the type of tripod and on shooting conditions.
NORMAL and SPORT are recommended if the camera is mounted on a monopod.

The Lens Hood

The lens hoods protect the lens and block stray light that would otherwise cause flare or ghosting.

Attaching the Hood

Align the lens hood mounting mark ( ) with the lens hood alignment mark ( ) and then rotate the hood (2) until the mark is aligned with the lens hood lock mark ( ).

When attaching or removing the hood, hold it near the __symbol on its base and avoid gripping it too tightly. Vignetting may occur if the hood is not correctly attached. The hood can be reversed and mounted on the lens when not in use.

Detaching the Hood

Press the lens hood lock release button (1), rotate the hood in the direction shown by the arrow (2), and remove it as shown (3).

Using a Tripod

If the lens is mounted on a camera, attach tripods to the lens tripod collar, not the camera. Be sure to secure the tripod collar lock screw, as otherwise the lens may unexpectedly slip from the collar, causing injury.

Attaching the Tripod Collar (Figure 2)

Insert the tripod collar mounting foot into the tripod collar (1) and fully tighten the tripod collar lock screw (2).

Rotating the Camera (Figure 3)

Slightly loosen the tripod collar ring fastening screw (1) and rotate the camera to “wide” (landscape) or “tall” (portrait) orientation using the rotation indices as guides (2). Tighten the tripod collar ring fastening screw (3).

Removing the Tripod Collar (Figure 4)

Fully loosen the tripod collar lock screw (1), depress the tripod collar lock release (2), and slide the tripod collar mounting foot from the tripod collar (3).

Lens Care

The lens returns to maximum aperture when removed from the camera. To protect the interior of the lens, store it out of direct sunlight or replace the lens caps.
Always support the lens when holding the camera. Failure to observe this precaution could damage the lens mount.
Do not pick up or hold the lens or camera using only the lens hood.
Keep the CPU contacts clean.
Should the rubber lens-mount gasket be damaged, cease use immediately and take the lens to a Nikon-authorized service center for repair.
Removing dust is normally sufficient to clean the glass surfaces of the lens.
The fluorine-coated front element can be cleaned simply by wiping it with a dry cloth. Fingerprints and other stains can be removed using a soft, clean cotton cloth or lens cleaning tissue; clean from the center outwards using a circular motion, taking care not to leave smears or touch the glass surface with your fingers. To remove stubborn stains, wipe gently using a soft cloth dampened with a small amount of distilled water, ethanol, or lens cleaner. Drop-shaped stains on the water- and oil-repellent fluorine-coated element can be removed with a dry cloth.
To remove smudges and fingerprints from the rear lens element (the element at the mount end of the lens), apply a small amount of ethanol or lens cleaner to a soft, clean cotton cloth or lens-cleaning tissue and clean from the center outwards using a circular motion, taking care not to leave smears or touch the glass with your fingers.
Never use organic solvents such as paint thinner or benzene to clean the lens.
The lens hood or Neutral Color (NC) filters can be used to protect the front lens element.
Attach the front and rear caps before placing the lens in its case.
If the lens will not be used for an extended period, store it in a cool, dry location to prevent mold and rust. Do not store in direct sunlight or with naphtha or camphor moth balls.
Keep the lens dry. Rusting of the internal mechanism can cause irreparable damage.
Leaving the lens in extremely hot locations could damage or warp parts made from reinforced plastic.
Rapid changes in temperature may cause damaging condensation inside and outside the lens. Before taking the lens from a warm to a cold environment or vice versa, place it in its case or a plastic bag to slow the change in temperature.

Supplied Accessories

LC-77 77 mm snap-on Front Lens Cap
LF-4 Rear Lens Cap
HB-78 Bayonet Hood
CL-M2 Lens Case

Compatible Accessories

77 mm screw-on filters
TC-14E/TC-14E MI/TC-14E I11/TC-17E IV/TC-20E/TC-20E IV/TC-20E III AF-1/AF-S Teleconverters

Specifications

Nikon reserves the right to change the appearance, specifications, and performance of this product at any time and without prior notice.

Retain this International Warranty with proof of purchase (bill of sale) for your records

Nikon Corp. LENS ONE YEAR WORLDWIDE LIMITED WARRANTY

(Excluding the Continental United States, Alaska, Hawaii, Puerto Rico, and U.S. Virgin Islands)

Welcome to the worldwide family of Nikon owners.

Your Nikon equipment has been manufactured to the highest quality standards by NIKON CORPORATION, Tokyo, Japan. This limited warranty entitles the original consumer purchaser to international warranty protection in accordance with these terms and conditions. It affords the original consumer purchaser warranty protection outside the Continental United States, Alaska, Hawaii, Puerto Rico and the U.S. Virgin Islands. Such warranty coverage is supplemental to and not in lieu of the United States Nikon Inc. Lens One Year USA Limited Warranty which is received by the original consumer purchaser with the Nikon product.

The Nikon product except for batteries is warranted by NIKON CORPORATION, Tokyo, Japan to be free from defects in materials or workmanship for a period of one ( 1)year from the date of purchase. To find an international Nikon Service Facility see: http://imaging.nikon.com/products/imaging/worldwide/index.htm. During this period any one of the international service facilities will service without charge any parts or assembly of parts found to be defective in materials or workmanship, subject to the following limitations and exclusions:

This warranty extends to the original consumer purchaser only and is not assignable or transferable.
This warranty shall not extend to any product which has been subject to misuse, alteration, abuse, negligence, accident or unauthorized repair or has had its serial number altered or removed.

The above warranty is expressly in lieu of all other warranties expressed or implied including but not limited to any implied warranty of merchantability or fitness for particular purpose, except to the extent prohibited by applicable law, in which event the duration of any implied warranty shall be limited to one (1) year from the date of purchase or such longer period as may be required by applicable law. Under no circumstances shall Nikon be liable for consequential, indirect, special, direct, exemplary, punitive or incidental damages arising out of or related to any breach of this warranty or any other claim regarding this product, including but not limited to, claims of negligence, strict liability or breach of contract.

Some jurisdictions, such as states or provinces, do not allow (a) limitations on how long an implied warranty lasts or (b) the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction.

In order to obtain international service, the original consumer purchaser should return the Nikon product, either in person or addressed to the Warranty Department of any authorized service facility listed on the above website, together with proof of purchase and proof of purchase date (bill of sale) and this warranty. The original consumer purchaser in returning this product must prepay all shipping and insurance costs to the service facility.