LIGHT MY BRICKS 75327 Lego Luke Skywalker Red Five Helmet Light Kit Installation Guide

June 5, 2024
LIGHT MY BRICKS

LEGO® LUKE SKYWALKER RED FIVE
HELMET
#75327 LIGHT KIT
INSTALLATION GUIDE

Light My Bricks

LEGO® LUKE SKYWALKER RED FIVE HELMET 75327 LIGHT KIT INSTALLATION GUIDE
Hi There!
We’re here to help you get started on the LEGO® Luke Skywalker Red Five Helmet (75327) Light Kit. This PDF details the instructions for the LED light kit only. If you run into any issues, please refer to the troubleshooting section towards the end of this guide. Have fun and enjoy!

**PACKAGE CONTENTS:

**

2 x Warm White 30cm Large Bit Light
2 x Cool White 30cm Large Bit Light
1 x Flashing Red 30cm Bit Light
1 x 6-Port Expansion Board
1 x USB Power Cable
(Power Source not Included) 

ASSORTED BRICKS:

  • 2 x Plate 1×6 – Black
  • 5 x Round Plate 1×1 W Open Stud – Black
  • 4 x Mod Plate 1×1 W Handle – Black
  • 2 x Arm Skeleton, Bent W Clips (Horizontal Grip) – Black

Before You Begin

Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead, ensure they are lying comfortably in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.
Connecting Cable Connectors To Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered  =” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert it into the port. If a plug won’t it easily into a port connector, do not force it.
Incorrectly inserting the connector can result in bent pins inside the port or possible overheating of the expansion board when connected.

Connecting Cable Connectors To Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector ith the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.

Connecting Micro Cable Connectors To Micro Expansion Board Ports
Take extra care when inserting the micro connectors to micro ports of Micro Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is similar to connecting rights and cables to Strip Lights. With the expansion board facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, do not force it. Use your fingernail to push the plastic part of the connector to the micro port.
Installing Bit Lights Under Lego® Bricks And Plates
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.

**** BLUEPRINT

INSTRUCTIONS

To ensure a smooth installation of your light kit, please read and follow each step carefully. If you run into any issues, please refer to the online troubleshooting guide.

FINAL PRODUCT

This finally completes the installation of the Light My Bricks Luke Skywalker Red Five Helmet 75327 Light Kit.

TROUBLESHOOTING

Light My Bricks lighting kits contain individual components that are very small and can be easily damaged if not handled correctly. To prevent unnecessary damage to components, we highly recommend that the User Guide section, “Important things to note” is read carefully. Follow the handling procedures in the User Guide to help prevent faults and damages to your Light My Bricks components.If you are experiencing issues with your Light My Bricks set, watch our troubleshooting video or read on for a list of common causes to help you troubleshoot

Firstly, ensure that the batteries have power using a battery charge gauge. If the batteries have no power, replace the batteries. If the batteries still have power, check to see if the batteries have been inserted correctly into the battery pack.
Check For CR2032 Batteries Using The Flat Battery Pack
Inside the battery pack is a symbol indicating which side the (round) CR2032 battery should be inserted. Check that the “+” side of the battery pack has the battery with the  +”  symbol facing downwards.
On the opposite side, the “-” side of the battery pack should have the battery flipped upside down, that is the “+” symbol facing upwards

Check For Cr2032 Batteries Using The Round Battery Pack
Inside the battery pack is a symbol indicating which side the (round) CR2032 battery should be inserted. In this case, for the stacked battery pack, ensure that BOTH batteries have the “+” symbol facing upwards.

Check for AA batteries using the AA battery pack
Inside the battery pack are symbols indicating which direction the AA battery should be inserted. The flat side of the battery should be paired with the spring side of the battery ack. If the batteries have been installed correctly and your kit still isn’t operating correctly, the next step is to check the wiring.

Check Your Wires
In order for Light My Bricks components to fit in between and underneath LEGO® bricks, the components need to be very small. Due to this nature, Light My Bricks components can be easily damaged when not handled correctly.
Be careful when removing unpacked components out of the packaging and ensure not to forcibly pull at the ires s this can damage the soldering that attaches the wires to the LEDs.|
If the wiring is detached from the LED itself, the light will not operate.
When connecting flights to your LEGO set, check that there are no pinched wires underneath or in between bricks and plates. When the wires are pinched and the exposed ires retouching each other, this can cause a crosswire and the lights to not function correctly.

Check Your Expansion Board Ports/ Strip Light Ports / Effects Board Ports
It is important to note that connectors can only be inserted to the expansion board, strip light, or effects board ports in one direction.
Forcibly inserting connectors in the incorrect direction will result in damaging the pins inside each of the ports on your component board.
Not only will a light connected to the damaged port not work, but if the pins inside the port are bent to a point they are touching each other, this can result in all other lights in the system stops working. This is a short circuit.

A short circuit can also result in overheating of the board, cable or batteries. If you suspect a short circuit, DISCONNECT POWER IMMEDIATELY Batteries can fail, catch ire, or even explode if left connected to a short circuit for too long.
If you suspect you have a faulty component due to a bent pin, try the following steps:
If you look carefully inside each of the ports, each port contains 2 small pins that should be straight. You will be able to identify a faulty part if it has any bent pins.

CONTACT US

If you have an inquiry regarding the online shop, our products, or a general inquiry please refer to our Frequently Asked Questions webpage. Alternatively, you can contact our  Customer Services team by visiting our online support portal.
support.lightmybricks.com
We thank you for purchasing this product and hope you enjoy it!

  lightmybricks.com

Documents / Resources

| LIGHT MY BRICKS 75327 Lego Luke Skywalker Red Five Helmet Light Kit [pdf] Installation Guide
75327, Lego Luke Skywalker Red Five Helmet Light Kit, 75327 Lego Luke Skywalker Red Five Helmet Light Kit
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals