LIGHT MY BRICKS 76182 Batman Cowl Light Kit Installation Guide

June 4, 2024
LIGHT MY BRICKS

LIGHT MY BRICKS 76182 Batman Cowl Light Kit

Light My Bricks

LEGO BATMAN COWL #76182 LIGHT KIT INSTALLATION GUIDE

Hi There!
We’re here to help you get started on the LEGO Batman Cowl (76182) Light Kit.
This PDF details the instructions for the LED light kit only.
If you run into any issues, please refer to the troubleshoot-ing section towards the end of this guide.
Have fun and enjoy!
INSTALLATION GUIDE

PACKAGE CONTENTS

  • 1 x White 30cm Bit Light
  • 2 x Cool White 30cm Bit Light
  • 2 x Cool White 30cm Large Bit Light
  • 1 x 6-Port Expansion Board
  • 1 x USB Power Cable (Power Source not Included)

ASSORTED BRICKS

  • 2 x Plate 1×6 – Black
  • 2 x Round Plate 1×1 W Open Stud – Black
  • 4 x Mod Plate 1×1 W Handle – Black
  • 2 x Arm Skeleton, Bent W Clips (Horizontal Grip) – Black

Before You Begin

Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO bricks, plates, and tiles providing they are laid correctly between the LEGO studs. Do NOT forcefully join LEGO together around cables; instead ensure they are laying comfortably in between each stud.
CAUTION: Forcing LEGO to connect over a cable can result in damaging the cable and light.

Connecting Cable Connectors To Expansion
Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can can result in bent pins inside the port or possible overheating of the expansion board when connected.

Connecting Cable
Connectors To Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it. Doing so will damage the plug and the connector.

Connecting Micro Cable
Connectors To Micro
Expansion Board Ports
Take extra care when inserting the
micro connectors to micro ports of Micro Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is similar to connecting lights and cables to Strip Lights. With the expansion board facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, do not force it. Use your fingernail to push the plastic part of the connector to the micro port.

Installing Bit Lights Under
Lego Bricks And Plates
When installing Bit Lights under LEGO pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO studs or in between.

BLUEPRINT

INSTRUCTIONS

To ensure a smooth installation of your light kit, please read and follow each step carefully. If you run into any issues, please refer to the online troubleshooting guide.

If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues in our troubleshooting section.

FINAL PRODUCT

This finally completes installation of the Light My Bricks Batman Cowl 76182 Light Kit.

TROUBLESHOOTING

  • Light My Bricks lighting kits contain individual components that are very small and can be easily damaged if not handled correctly.

  • To prevent unnecessary damage to components, we highly recommend that the User Guide section,
    “Important things to note” is read carefully. Follow the handling procedures in the User Guide to help prevent faults and damages to your Light My Bricks components.

  • If you are experiencing issues with your Light
    My Bricks set, watch our troubleshooting video or read on for a list of common causes to help you troubleshoot.

  • Firstly, ensure that the batteries have power using a battery charge gauge.

  • If the batteries have no power, replace the batteries.

  • If the batteries still have power, check to see if the batteries have been inserted correctly into the battery pack.

Check For CR2032 Batteries
Using The Flat Battery Pack
Inside the battery pack is a symbol indicating which side the (round) CR2032 battery should be inserted. Check that the “+” side of the battery pack has the battery with the “+” symbol facing downwards.
On the opposite side, the “-” side of the battery pack should have the battery flipped upside down, that is the “+” symbol facing upwards

Check For Cr2032 Batteries
Using The Round Battery
Pack
Inside the battery pack is a symbol indicating which side the (round) CR2032 battery should be inserted. In this case, for the stacked battery pack, ensure that BOTH batteries have the “+” symbol facing upwards.

Check for AA batteries using the AA battery pack
Inside the battery pack are symbols indicating which direction the AA battery should be inserted. The flat side of the battery should be paired with the spring side of the battery pack.
If the batteries have been installed correctly and your kit still isn’t operating correctly, the next step is to check the wiring.

Check Your Wires
In order for Light My Bricks components to fit in between and underneath LEGO® bricks, the components need to be very small. Due to this nature, Light My Bricks components can be easily damaged when not handled correctly.
Be careful when removing unpacked components out of the packaging and ensure not to forcibly pull at the wires as this can damage the soldering that attach the wires to the LEDs.
If the wiring is detached from the LED itself, the light will not operate.
When connecting lights to your LEGO set, check that there are no pinched wires underneath or in between bricks and plates. When the wires are pinched and the exposed wires are touching each other, this can cause a crosswire and the lights to not function correctly.

Check Your Expansion Board Ports/ Strip Light Ports
Effects Board Ports
It is important to note that connectors can only be inserted to the expansion board, strip light, or effects board ports in one direction.
Forcibly inserting connectors in the incorrect direction will result in damaging the pins inside each of the ports on your component board.
Not only will a light connected to the damaged port not work, but if the pins inside the port are bent to a point they are touching each other, this can result in all other lights in the system to stop working. This is a short circuit.

A short circuit can also result in overheating of the board, cable or batteries. If you suspect a short circuit, DISCONNECT POWER IMMEDIATELY Batteries can fail, catch fire, or even explode if left connected to a short circuit for too long.
If you suspect you have a faulty component due to a bent pin, try the following steps:
If you look carefully inside each of the ports, each port contains 2 small pins that should be straight. You will be able to identify a faulty port if it has any bent pins.

CONTACT US
If you have an enquiry regarding the online shop, our products or a general enquiry please refer to our Frequently Asked Questions webpage. Alternatively, you can contact our Customer Services team by visiting
our online support portal.
support.lightmybricks.com
We thank you for purchasing this product and hope you enjoy!

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals