PHILIPS FW1 Wireless Subwoofer and Speaker Instruction Manual
- June 6, 2024
- Philips
Table of Contents
FW1 Wireless Subwoofer and Speaker
Instruction Manual
TV Audio Setup
Follow the on-screen setup.
Surround sound Setup
Follow the on-screen setup.
Wired connection (Sub-in)
When the source switch is at Sub in source, FW1 shall behave as a wired
subwoofer. It shall render the subwoofer signal via analog input.
- Use a subwoofer cable to connect the other device or TV’s audio output sockets to the Sub in the socket on the unit.
- When FW1 is used as an as wired subwoofer, the source switch must be at Sub in position.
- The available controls and functions (at the back of the subwoofer) are as below:
| Functional | Settings | Default |
|---|---|---|
| Gain | -6 dB to +6 dB | 0 dB |
| Crossover | 25 to 150 Hz | – |
| Phase | 0 or 180 degree | 0 degree |
Note
When FW1 is a Play-fi subwoofer, the above controls and functions are not
applicable.
Wireless connection (Play-Fi > RF link)
Wireless connection (RF link > Play-Fi)
Upgrade firmware
To get the best features and support, update your product with the latest
firmware version.
Update firmware via Philips Sound (Settings > Fine Tune / Update Firmware)
The firmware for MCU and DSP can be upgraded to the latest version via Philips
Sound powered by DTS Play-fi. Please go to the settings menu and select PS
Fine Tune / Update Firmware option to check it out. If the upgrade is
released, the upgraded icon can be pressed to proceed automatically. Once this
product is connected to Wi-Fi, it can receive over-the-air firmware updates.
Always upgrade with the latest firmware version to improve the performance of
this product.
Factory reset
Reset device to default setting.
1 Set is ON, use a needle to push the Reset button on the rear of the
subwoofer for 5 seconds.
You will hear a tone and then the subwoofer will automatically restart.
The subwoofer is restored to factory defaults.
Product specifications
Note
Specifications and design are subject to change without notice.
Wireless
5.8G Wireless frequency range Transmitter power (EIRP)| 5742 ~ 5852 MHz ≤
10dBm
---|---
Network supported
WiFi IEEE 802.11a/b/g/n/ac Wireless frequency band (Wi-Fi) /Radio frequency
power transmitted (EIRP)
2.4G Wi-Fi ………………………………2400 ~ 2483.5 MHz / ≤ 20dBm
5G Wi-Fi
5150 ~ 5350 MHz / ≤ 20dBm
5470 ~ 5725 MHz / ≤ 27dBm
5725 ~ 5850 MHz / ≤ 14dBm
Subwoofer
| Power supply | 100-240V~50/60Hz |
|---|---|
| MAX output power by the speaker | 240W RMS @10% THD |
| Power consumption | 50 W |
| Standby consumption | < 0.5 W |
| USB | 5V 500mA |
| Frequency Response | 25Hz – 150Hz |
| Impedance | 3 Ω |
| Dimensions (W x H x D) | 240 x 472.5 x 400 mm |
| Weight | 13.6 kg |
| Operating Temperature | 0°C – 45°C |
Troubleshooting
Note
• Never remove the casing of the product.
To keep the warranty valid, never try to repair the product yourself. If you
have problems using this product, check the following points before you
request service. If you still have a problem, get support at
www.philips.com/support.
No power
- Ensure that the AC cord is properly connected.
- Ensure that there is power at the AC outlet.
Sound
- When the playback freezes and there’s no sound in Wi-Fi mode, please check whether your home network is normal. Distorted sound or echo.
- If you play audio from TV through this product, make sure that the TV is muted.
Wi-Fi
A Wi-Fi Connection cannot be established.
- Check the availability of the WLAN network on the router.
- Place the Wi-Fi router closer to the unit.
- Make sure the password is correct.
- Check the WLAN function or reboot the modem and Wi-Fi router.
Play-fi
Cannot discover the play-fi-supported devices from the app.
- Make sure the device is connected to the Wi-Fi. Cannot play play-fi music.
- Certain network services or contents available through the device may not be accessible in case the service provider terminates its service.
- When the first time set up is not successful, close the Philips Sound app powered by DTS Play-fi. Restart the app.
- When the speaker was set as Stereo Pairs or Surround Sound, the speaker needs to be disconnected in the app before use separately.
Specifications are subject to change without notice. Please visit
www.Philips.com/support for the latest
updates and documents.
Philips and the Philips Shield Emblem have registered trademarks of
Koninklijke Philips N.V. and are used under license.
This product has been manufactured by and is sold under the responsibility of
MMD Hong Kong Holding Limited. or one of its affiliates, and MMD Hong Kong
Holding Limited. is the warrantor in relation to this product.
TAFW1RE_UM_EN_V0.5_20220309
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>