OUTWATER 24V RGB Ribbon Flex is Manufactured User Manual
- June 10, 2024
- OUTWATER
Table of Contents
OUTWATER 24V RGB Ribbon Flex is Manufactured
Product Information: Outwater 24V RGB Ribbon Flex
The Outwater 24V RGB Ribbon Flex is a high-quality lighting strip designed for various lighting applications. It is manufactured with linkable bands for easy extension, splicing, and power supply. The Ribbon Flex has a power band pattern consisting of a single band, three double bands, and a single band that repeats. The product has two different power bands: a double power band and a single power band. Various options are available to extend, splice & power your Ribbon Flex allowing maximum usage. There are four options for Ribbon Flex:
- Power Linking Cable (LED-RIBBON-100U-RL) – $4.00 ea.
- Hardwire Cable (LED-RIBBON-100U-RT) – $7.85 ea.
- End To End Direct Connector (LED-RIBBON-100U-EE) – $2.00 ea.
- Connecting Cable (LED-RIBBON-100U-R1) – $7.00 ea. (24) or (LED-RIBBON-100U-R2) – $7.75 ea. (36)
The Ribbon Flex can either be hardwired directly to the power supply or connected with these options.
Product Usage Instructions
- When planning your lighting application, take note that there are two different power bands on the Ribbon Flex lighting strip: a double power band and a single power band.
- The double power band should be cut in between the two power bands.
- Cut left or right of the double power band. Do not cut through the band.
- After Ribbon Flex has been cut, slice and peel back the clear epoxy layer exposing the conductive ends. Be certain not to cut through the Ribbon Flex itself.
- Open the connector and insert Ribbon Flex under the metal clips.
- After inserting the Ribbon Flex, simply snap the cover back into place.
By following these instructions, you can easily extend, splice, and power your
Ribbon Flex for maximum usage. If you have any questions or concerns, please
refer to the user manual or contact customer support for assistance.
Power Band Pattern: Single Band, 3 Double Bands & Single Band Then Pattern
Repeats
Various options are available to extend, splice & power your Ribbon Flex
allowing maximum usage. Please pay attention to the following rules when
cutting at a single or double band.
Assembly
-
Step. 1- When planning your lighting application, take note that there are two different power bands on the Ribbon Flex lighting strip.
A. Double Power Band
The double power band should be cut in between the two power bands. The double power band options:
-
Powered Linking Cable
-
Hardwired Cable
-
End To End Direct Connector
-
Connecting Cable
B. Single Power Band
Cut left or right of band. Do not cut through the band.
When powered from the left, cut to the left of the single power band.
When powered from the right, cut to the right of the single power band.
The single power band options: -
Powered Linking Cable
-
Hardwired Cable
-
Options for Ribbon Flex
-
Power Linking Cable
LED-RIBBON-100U-RL- $4.00 ea.
Connects directly to power supply with male and female connections -
Hardwire Cable
LED-RIBBON-100U-RT- $7.85 ea.
Hardwire directly to power supply -
End To End Direct Connector
LED-RIBBON-100U-EE- $2.00 ea.
Directly connect 2 pieces of cut ribbon flex -
Connecting Cable
LED-RIBBON-100U-R1- $7.00 ea. (24”) LED-RIBBON-100U-R2- $7.75 ea. (36”)
Connects 2 pieces of ribbon flex together.- When changing levels or avoiding obstacles that do not need light
- Available in 2 ft. or 3 ft. cables
-
Step. 2- After Ribbon Flex has been cut, slice and peel back the clear epoxy layer exposing the conductive ends.
Note: Be certain not to cut through the Ribbon Flex itself -
Step. 3- Open the connector and insert Ribbon Flex under the metal clips.
-
Step. 4- After inserting the Ribbon Flex, simply snap the cover back into place.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>