OUTWATER INDUSTRIES DGL-KY-CAM Horizontal Left Keypad Function Digital Cam Lock Instruction Manual

: June 2, 2024
: OUTWATER INDUSTRIES

OUTWATER INDUSTRIES DGL-KY-CAM Horizontal Left Keypad Function Digital Cam Lock

MOUNTING DETAILS

ORIENTATION OPTIONS

INSTALLATION

See Figure 1 for available mounting hardware for the lock. When mounting the lock to a cabinet door or drawer, a separately mounted handle should be used to operate, open and close the door or drawer. When installing the lock to the cabinet/drawer, you have the option to fasten the lock body with a nut or a retaining clip. A ‘wonder’ washer (#3) is provided for installation in a drilled hole through either wood or metal panels.
Additional mounting fasteners (10) and/or double sided tape are provided and must be added through the battery extremity of the housing. Select the fasteners that best fit your panel material and thickness. If drilling is needed for thick panels, a drilling template is provided. (See right).

The installation template at the end of this manual can be used to drill a mounting hole for the unit. Wood screw or self-tapping metal screw options are provided. In addition, double stick tape can be used solely or in conjunction with the mounting screw to further secure the lock. Allow tape to cure for 72 hours.
Prior to installation and insertion of the battery, the knob of the lock mechanism will be free moving. The unit hardware contains a cam stop (#6) for both 90 and 180 degrees. Select and install the desired cam stop and cam (#7). Position the cam stop so the knob rotation is clockwise or counter-clockwise as desired

MOUNTING TEMPLATE

Measure before drilling. If the length of the segment is different from 1.00″ the template dimensions will be scaled accordingly. The mounting screw for the lock housing must be installed before installing the battery .

Select appropriate mounting screw. If a lock spacer is required, a mounting screw must be…

If mounted on sheet metal:

**If mounted to wood panel with threaded insert:

In addition, the double stick tape can be used solely or in conjunction with the mounting screw to further secure the lock. Allow tape to cure for 72 hours.**

BATTERY

After installing the lock the mounting surface, the battery and holder can be inserted into the lock. The cover for the battery holder also serves to lock the holder into the lock housing. The battery cover must be in the fully open position before inserting the holder. The battery holder screw cannot be protruding from the bottom of the battery holder, it must be flush with the holder so the holder can be inserted.

Check that the battery is properly inserted into the holder. The “+” surface of the battery should be inserted into the holder against the surface of the holder marked with the “+” symbol. Insert the battery holder into the lock with the holder cover in the fully open position and with the battery holder screw flush to the bottom of the holder until the holder is fully seated. Next, use the hex tool to fasten the battery holder screw into the lock body. Last, swing the battery holder cover to the closed position, push in and fully seat the cover into the battery holder until it is flush to the lock body.

If the battery is inserted while the knob is locked, you should hear the lock mechanism click and the unit will lock. If the battery is inserted while the knob is unlocked, after turning the knob to the locked position you should hear the lock mechanism click and the unit will lock. If the unit will not lock after inserting the battery, enter the factory code, move the knob to the unlocked position, and move the knob to the locked position and you should hear the lock mechanism click and the unit will lock. If the unit still does not lock, replace the battery

REPLACING THE BATTERY

If the battery is inserted while the knob is locked, you should hear the lock mechanism click and the unit will lock. If the battery is inserted while the knob is unlocked, after turning the knob to the locked position, you will hear the lock mechanism click and the unit will lock. If the unit will not lock after inserting the battery, enter the factory code, move the knob to the unlocked position, then move the knob to the locked position and you should hear the lock mechanism click and the unit will lock. If the unit does not lock, replace the battery

SPECIFICATIONS

Operating Temperature: 0 – + 50 C
Storage Temperature: -10 – + 70 C
Operating Moisture: 20% – 80% Rh (without condensation)
Replacement Battery: 3 volt lithium CR2032
Battery Life: 3 to 5 years typical or 50,000 operations
ATTENTION: Battery life may vary with battery brand and environmental conditions.

CARE AND CLEANING

To clean the housing surface, apply a non-acid based cleaner to a clean cotton cloth. Do not spray cleaner directly on the surface. Wipe down the keypad and housing surface of excess cleaner

GETTING STARTED

TWO OPERATING MODES:
MULTIPLE LEVELS OF ACCESS:
OPERATION:
SWITCHING MODES:

Station mode (repeated use with the same code)
Locker mode (use with a temporary code)

To determine which operating mode the lock is in, remove the battery, press and release the program button, and reinsert the battery. Note the color sequence of the LED flashes when the battery is reinserted:

(green, red, yellow) indicates station mode lights flashing in the sequence

(green, yellow, red) indicates locker mode lights flashing in this sequence

1-2-3-4-5 KEYPAD BUTTONS:
For entering and programming lock codes.

PROGRAM BUTTON:
Initiate the lock programming mode by pressing the front thin edge of the black button inward toward the mounting surface the unit is mounted to.
KNOB:
To move the lock mechanism 90 to 180 degrees clockwise or counter-clockwise from the locked and unlocked states.
The Green and Red LED’s will flash and illuminate to indicate operating conditions per the descriptions below.
The Yellow LED will flash 5 times after the lock is operated to signify the battery level is low and should be replaced.

MULTIPLE LEVELS OF ACCESS

Master code
Supervisor code
User code
Note: This unit is pre-programmed with a factory master code
The factory master code is : 135243

OPERATION

Unlock with a code by entering a valid code. The green LED will illuminate. Turn the knob to unlock. To lock, turn the knob to align the knob pointer with the lock icon on the keypad.

SWITCHING MODES:

Unlock the unit and turn the knob to the unlocked position
Remove the battery for 10 seconds
While holding the program button, , reinsert the battery and wait until all 3 LED’s fade in and fade out simultaneously.
Release the program button
Enter the 6 digit master code. When the master code is entered correctly, the yellow LED will illuminate.
Press the button number 1 for station mode, press button number 2 for locker mode.
Once the lock switches modes, the LED’s will flash in a certain order according to the mode selected
a. Locker Mode:
b. Station Mode:
Proceed to operate the lock in the selected mode

STATION MODE PROGRAMMING INSTRUCTIONS

MASTER CODE:

Turn knob to locked position
Press program button 5 times, (Green light illuminates)
Enter temporary code that came with the lock, (531423) or (135243)
If correct, both red and green lights will illuminate, (If not, only red light will flash)
Once both lights are on, enter temporary code again, (Yellow light will then illuminate)
Enter new master code twice, (If correct, all 3 lights will flash for 3 seconds; otherwise, only red light will flash)
New master code is set

SUPERVISOR CODE:

Press program button once, (Green light illuminates)
Enter master code, (Red light will flash)
Enter supervisor code, (3-6 digits)
Press program button again, (Green light will flash 6 times)
New supervisor code is set

USER CODE

Press program button twice, (Red light illuminates)
Enter supervisor code, (Yellow light will flash indicating correct supervisor code was entered)
Enter user code, (3-6 digits)
Press program button again, (Green light will flash 6 times)
User code is set

CHANGE THE MASTER CODE:

Press program button 5 times, (Green light illuminates)
Enter old master code, (If correct, both red and green lights illuminate)
Enter old master code again (All 3 lights illuminate)
Enter new master code twice (All lights will flash 6 times)
Master code is changed

CHANGE THE SUPERVISOR CODE:

Press program button once, (Green light illuminates)
Enter master code (Red light illuminate)
Enter new supervisor code
Press program button once (Green light will flash 6 times)
Supervisor code is changed

REMOVE A USER CODE:

Press program button twice, (Red light illuminates)
Enter supervisor code, (Yellow light illuminates for 10 seconds)
Enter 1-1-1-1-1
Press program button once, (Green light will flash 6 times)
User code is now removed

Note: Can have only one master, one supervisor and one user per lock.

LOCKER MODE PROGRAMMING INSTRUCTIONS

Note: The lock must be unlocked to program in locker mode. User codes are one time use.

MASTER CODE:

Turn knob to unlocked position
Press program button once, (Green light illuminates)
Enter temporary code that came with lock, (531423) or (135243), (Green light illuminates again)
Enter new master code, (Green light will flash 6 times)
New master code is set

LOCK USING A SINGLE USE CODE (4 DIGITS):

Enter new user code, (Green light illuminates)
Turn knob to lock, (Green light will flash 3 times)
Single use code is now set (NOTE: Red light will flash every 3 seconds to show lock is in use)

UNLOCK USING A SINGLE USE CODE:

Enter user code, (Green light illuminates)
Turn knob to unlock
The single use code is now erased

UNLOCK USING MASTER CODE:

Press program button once, (Green light will flash)
Enter master code, (Green light illuminates)
Turn knob to unlock

CHANGE THE MASTER CODE:

Press program button once, (Green light illuminates)
Enter old master code, (Green light will illuminates again)
Enter new master code, (Green light will flash 6 times)
New master code is set

Outwater Industries, Inc. assumes no liability for improper installation.

Documents / Resources

| OUTWATER INDUSTRIES DGL-KY-CAM Horizontal Left Keypad Function Digital Cam Lock [pdf] Instruction Manual
DGL-KY-CAM Horizontal Left Keypad Function Digital Cam Lock, DGL-KY-CAM, Horizontal Left Keypad Function Digital Cam Lock, Keypad Function Digital Cam Lock, Function Digital Cam Lock, Digital Cam Lock, Cam Lock, Lock
---|---