OUTWATER LED INLINE RF Impact Protection for Furniture User Manual
- June 10, 2024
- OUTWATER
Table of Contents
OUTWATER LED INLINE RF Impact Protection for Furniture
Product Information: LED-INLINE-RF
The LED-INLINE-RF is an LED light controller that can be controlled by a remote control. It has various features like lighting mode, dynamic mode, dimmer adjust shortcuts, speed adjust, and brightness adjust. The device accepts DC5V to 24V power supply and has a peak output current of 6A. The remote control is an RF wireless type with a frequency of 433.92 MHz, and it can operate from a distance of more than 30m in open areas. The device has 8 dynamic modes, 10 levels of dynamic speed adjustment, and 256 grades of lighting brightness adjustment. The PWM grade smooth dimmer effect ensures uniform dimming of the LEDs.
Product Usage Instructions
Step 1: Power Supply Connection
- Connect the device to a DC5V to 24V power supply.
- Connect the red cable to positive, and the black cable to negative.
Step 2: LED Output Connection
- Connect the red cable to the LED positive, and the black cable to negative.
- The peak output current is 6A. Please reduce the load if the main unit is overheating.
- CAUTION: DO NOT SHORT CIRCUIT THE LED OUTPUT.
THIS MAY LEAD TO PERMANENT DAMAGE!
Step 3: Remote Control Usage
- Pull out the insulated part before using the remote control.
- The RF wireless remote signal can pass through barriers, so it’s not necessary to aim at the main unit when operating.
- For proper reception of the remote signal, do not install the main unit in closed metal parts.
- The remote battery is a 3V CR2025 type. Please only replace it with the same type of battery.
Step 4: Device Operation
- Press the ON/Standby key to turn on the device or switch to standby mode.
- The unit will turn on and restore to the previous status at the power-on moment.
- Press the Lighting Mode key to switch to lighting mode from dynamic mode.
- Press Dimmer Adjust Shortcuts keys 3, 8, or 9 to switch to 100%, 50%, or 25% brightness lighting mode.
- Press Dynamic Mode Adjust keys 4 or 6 to switch to dynamic mode from lighting mode or switch between different dynamic modes.
- Press Speed Adjust keys 5 or 7 to adjust the playing speed of dynamic modes.
- Press SPEED+ to increase speed and press SPEED- to decrease speed.
- Press Brightness Adjust keys 10 or 11 to adjust lighting mode brightness.
- Press BRIGHT+ to increase brightness, and press BRIGHT- to decrease brightness.
Note: Please follow the product specifications and usage instructions carefully to ensure proper functioning of the LED-INLINE-RF device.
Contact Information:
- Web: www.outwater.com
- Phone: 1-800-631-8375
FEATURES:
- • Dimmer & Dynamic
- 10-Level Dimmer
- Speed Adjustable
- Ultra Slim Design
- 8 Dynamic Effects
- 256-Grade PWM
- Card Type Remote
- Smooth Dimmer Effect
- Auto Save Function
Remote Controls
-
1. Turn ON/Standby Mode
Press this key to turn on unit or switch to standby mode. Unit will turn ON and restore to previous status at powering on moment. -
2. Lighting Mode
Switch to lighting mode from dynamic mode -
3 | 8 | 9. Dimmer Adjust Shortcuts
Switch to 100%, 50%, or 25% brightness lighting mode -
4 | 6. Dynamic Mode Adjust
Switch to dynamic mode from lighting mode, or switch between different dynamic modes. -
5 | 7. Speed Adjust
Adjust playing speed of dynamic modes. Press SPEED+ to increase speed and press SPEED- to decrease. -
10 | 11. Brightness Adjust [Dimmer]
Adjust lighting mode brightness. Press BRIGHT+ and press BRIGHT- to decrease.
SPECIFICATIONS:
Dynamic Mode | 8 Modes |
---|---|
Dynamic Speed Level | 10 Levels |
Lighting Brightness Level | 10 Levels |
PWM Grade | 256 Grades |
Smooth Dimmer Effect | Yes |
Working Voltage | DC:5V~24V |
Output Current | Peak 6A |
Remote Control Mode | RF Wireless |
Remote Frequency | 433.92 MHz |
Remote Distance | > 30m In Open Areas |
INSTALLATION:
-
Power Supply
This unit accepts a DC5V to 24V power supply. The red cable should be connected to positive and the black cable to negative. Please select the proper power supply according to the LED application. -
LED Output
The red cable should be connected to the LED positive and the black cable to negative. The peak output current is 6A. Please reduce the load if the main unit is overheating.
CAUTION: DO NOT SHORT CIRCUIT THE LED OUTPUT. THIS MAY LEAD TO PERMANENT DAMAGE! -
Remote Control
Please pull out the insulated part before using. The RF wireless remote signal can pass through barriers, so it’s not necessary to aim at the main unit when operating. For proper reception of the remote signal, do not install the main unit in closed metal parts. The remote battery is a 3V CR2025 type. Please only replace with the same type of battery.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>