IMG STAGELINE CALDERA-T6 Active Speakers Instruction Manual

June 4, 2024
IMG STAGELINE

IMG STAGELINE CALDERA-T6 Active Speakers

INSTALLATION

IMG STAGELINE CALDERA-T6 Active Speakers-1

Active Speakers
These instructions are intended for users with basic knowledge of PA technology. Please read the instructions carefully prior to operation and keep them for later reference.

Applications
This pair of high-quality active speakers is suitable for HiFi applications, as a monitor system in home recording studios, as high-end PC speakers, for AV presentations and for all other applications in small to medium-sized rooms where it is important to have a sound reproduction rich in detail. Each speaker system has a 16 cm bass-midrange speaker with polypropylene cone and a 2.54 cm soft dome tweeter,each controlled by separate power amplifiers.
The amplifiers are protected against short circuit and overheating.

Safety Notes

The product corresponds to all relevant directives of the EU and is therefore marked with .
The product corresponds to all relevant UK legislations and is therefore marked with UKCA.
WARNING The product uses dangerous mains voltage. Leave servicing to skilled personnel and do not insert anything into the air vents!
Inexpert handling may result in electric shock.

  • The product is suitable for indoor use only.
    Protect it against dripping water, splash water and high air humidity. The admissible ambient temperature range is 0 – 40 °C.

  • Do not place any vessels filled with liquid, e. g. drinking glasses, on the product.

  • The heat produced inside the product must be dissipated by air circulation; never cover the air vents.

  • Do not use the product and immediately disconnect the mains plug from the socket

    1. if the product or the mains cable is visibly damaged,
    2. if a defect might have occurred after the product was dropped or suffered a similar accident,
    3. if malfunctions occur.
      Any repairs must be carried out by specialists.
  • Never pull the mains cable to disconnect the mains plug from the socket, always seize the plug.

  • For cleaning the product, only use a dry, soft cloth; never use water or chemicals.

  • No guarantee claims for the product and no liability for any resulting personal damage or material damage will be accepted if the product is not correctly used or not expertly repaired.

If the product is to be put out of operation definitively, dispose of the product in accordance with local regulations.

Setting up and Connecting

Set up the speakers on a flat surface and align them to the ears of the listener. The tweeters should be at ear level if possible. Do not place the speakers too close to walls or in corners; this will distort the frequency response and impede any heat dissipation of the integrated amplifier.

Connecting an audio source
To connect an audio source with line level (e. g. CD player, mixer output, line output of a computer), a 6.3 mm jack (2) and an XLR connector (3) are available which can be used alternatively.
Both inputs are balanced. To connect audio sources with unbalanced signals, use a 2-pole 6.3 mm plug for the 6.3 mm jack or a corresponding adapter for the XLR connector (bridge between pin 1 and pin 3).
The contacts of both inputs are directly connected to each other so that the second input can also be used to forward the signal, e. g. to another active speaker.

Power supply
For power supply, use the mains cable provided to connect the IEC connector “230 V~/ 50 Hz”(5) to a mains socket (230 V/ 50 Hz).

Operation
  1. To prevent the initial volume from being too high, turn the control VOL (1) to the left stop (position “−∞”) before switching on for the first time.

  2. Use the ON / OFF switch (4) to switch on the speaker system. The power indicator on the front (below the tweeter) lights up.

  3. Use the control VOL (1) to set the desired volume.
    CAUTION
    Never adjust a very high volume. Permanent high volumes may damage your hearing!

  4. Switch off the speaker system after use.
    Note: To avoid switching noise, always switch on the devices connected before switching on the speakers. After use, switch off the speakers first.

Specifications

  • System:  2-way bass reflex, active
  • Amplifier power of each speaker system
    • Power rating: 55 W (30 W + 25 W)
    • Peak power: 100 W
  • Frequency range: 50 – 20 000 Hz
  • Input
    • Sensitivity:  1.5 V
    • Max. input level:  7 V
    • Impedance:  32 kΩ
    • Connection: XLR connector and 6.3 mm jack, balanced

Pin configuration:

Speakers

  • Bass-midrange speaker: . 16 cm, polypropylene
  • Tweeter: 2.54 cm, soft dome tweeter
    • Sensitivity:  89 dB / W/ m
  • Max. SPL:  105 dB
  • Radiation angle
    • horizontal:  120°
    • vertical:  100°
  • Power supply:  230 V/ 50 Hz /110 VA
  • Ambient temperature:  0 – 40 °C
  • Cabinet material:  MDF wood
  • Dimensions
    • Width:  210 mm
    • Height:  320 mm
    • Depth:  255 mm
  • Weight
    (of each speaker system): 7 kg

Subject to technical modification.

All rights reserved by MONACOR ® INTERNATIONAL GmbH & Co. KG.
No part of this instruction manual may be reproduced in any form or by any means for any commercial use.

Copyright© by MONACOR INTERNATIONAL. All rights reserved.
A-2100.99.01.11.2021

UK Importer: Monacor UK Ltd.,
Unit 8, Plover Close,
Newport Pagnell, BEDS., MK16 9PS
MONACOR INTERNATIONAL GmbH & Co. KG, Zum Falsch 36, 28307 Bremen,
Germany

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals