DRAPER 56177 Twin-Triple Reversible Puller Instruction Manual
- June 10, 2024
- DRAPER
Table of Contents
INSTRUCTIONS FOR
Twin/Triple
Reversible Puller
Stock No.56177 Part No.N136
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE
AND EFFECTIVE USE OF THIS PRODUCT.
GENERAL INFORMATION
This manual has been compiled by Draper Tools and is an integrated part of the
product with which it is enclosed and should be kept with it for future
references.
This manual describes the purpose for which the product has been designed and
contains all the necessary information to ensure its correct and safe use. We
recommend that this manual is read before any operation or, before performing
any kind of adjustment to the product and prior to any maintenance tasks. By
following all the general safety instructions contained in this manual, it
will ensure both product and operator safety, together with longer life of the
product itself.
All photographs and drawings in this manual are supplied by Draper Tools to
help illustrate the operation of the product.
Whilst every effort has been made to ensure accuracy of information contained
in this manual, the Draper Tools policy of continuous improvement determines
the right to make modifications without prior warning.
SPECIFICATION
The Draper Tools policy of continuous improvement determines the right to change specification without notice.
Stock No. ……………………………………………………56177
Part No. ……………………………………………………….N136
Maximum Reach …………………………………………….150mm
Maximum Spread ………………………………………………100mm
Two Leg
Short Leg
Reach ……………………………………………………………… 75mm
Spread ………………………………………………………….. 150mm
Long Leg
Reach ………………………………………………………… 120mm
Spread ……………………………………………………….. 150mm
Three Leg
Short Leg
Reach ……………………………………………………………….75mm
Spread ……………………………………………………………….150mm
Long Leg
Reach ……………………………………………………………… 120mm
Spread ……………………………………………………………… 150mm
GUARANTEE
Draper tools have been carefully tested and inspected before shipment and are
guaranteed to be free from defective materials and workmanship.
Should the tool develop a fault, please return the complete tool to your
nearest distributor or contact Draper Tools Limited, Chandler’s Ford,
Eastleigh, Hampshire, SO53 1YF. England.
Telephone: (023) 8026 6355.
If upon inspection it is found that the fault occurring is due to defective
materials or workmanship, repairs will be carried out free of charge. This
guarantee period covering parts/labour is 12 months from the date of purchase.
The guarantee is extended to 24 months for parts only. This guarantee does not
apply to normal wear and tear, nor does it cover any damage caused by misuse,
careless or unsafe handling, alterations, accidents, or repairs attempted or
made by any personnel other than the authorised Draper warranty repair agent.
This guarantee applies in lieu of any other guarantee expressed or implied and
variations of its terms are not authorised.
Your Draper guarantee is not effective unless you can produce upon request a
dated receipt or invoice to verify your proof of purchase within the guarantee
period.
Please note that this guarantee is an additional benefit and does not affect
your statutory rights.
VERSATILITY
SAFETY
– INFORMATION:
- Application of pressure on the forcing screw increases the grip of the self-locking legs.
- By reversing the legs the amount of reach and spread can be varied to suit the job.
- The link nuts of this puller must not be locked tight, as this will prevent the self- locking action.
- Always clean and lubricate the forcing screw before and after use.
INSTRUCTIONS:
- Withdraw the forcing screw to provide sufficient reach.
- Ensure the puller is located at the centre of the workpiece before applying any pressure on the forcing screw.
- Locate the reversible legs around the workpiece. Hand tighten the forcing screw.
- Check that the puller is centrally located and that the forcing screw is lined up with the axis of the shaft.
- Continue to apply pressure using the correct size of spanner or socket on the hexagon head of the forcing screw.
- Hit the striking head of the forcing screw with a soft faced hammer and then re- tighten with a spanner or socket.
- Continue this operation until the workpiece is removed.
IMPORTANT:
Trying to remove items by using the forcing screw alone will stress the triple
head and screw thread causing damage. For detailed and concise instructions on
the correct use of this tool, refer to the vehicle manufacturer’s handbook.
SAFETY FIRST:
A. Ensure the tool is fitted squarely to workpiece.
B. Do not use excessive pressure.
C. Avoid injury or damage due to sudden release of pressure or resistance.
D. Attempt to cover the puller and item being pulled as a precaution against
flying debris.
E. Take precautions against any sudden loss of balance caused by the release
of pressure.
CONTACTS
DRAPER TOOLS LIMITED,
Hursley Road,
Chandler’s Ford,
Eastleigh,
Hampshire.
SO53 1YF. U.K.
- Helpline: (023) 8049 4344.
- Sales Desk: (023) 8049 4333.
- General Enquiries: (023) 8026 6355.
- Fax: (023) 8026 0784
- Internet: www.draper.co.uk
- E-mail: sales@drapertools.com
YOUR DRAPER STOCKIST
©Published by Draper Tools Limited.
No part of this publication may be reproduced, stored in a retrieval system or
transmitted in any form or by any means, electronic, mechanical photocopying,
recording or otherwise without prior permission in writing from Draper Tools
Ltd.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>