WORX WA4300 Pruning Saw Extension Pole Instruction Manual

: June 4, 2024
: Worx

Table of Contents

WORX WA4300 Pruning Saw Extension Pole Instruction Manual
SAFETY INSTRUCTIONS
COMPONENT LIST
TECHNICAL DATA
OPERATING INSTRUCTIONS
- References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

WORX WA4300 Pruning Saw Extension Pole Instruction Manual

WORX WA4300 Pruning Saw Extension Pole.JPG

FIG 1 Overview.JPG

FIG 2.JPG

FIG 3.JPG

FIG 4.JPG

FIG 5.JPG

FIG 6.JPG

FIG 7.JPG

WARNING: This product can expose you to chemicals including lead and Di(2- ethylhexyl)phthalate (DEHP) which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

SAFETY INSTRUCTIONS

WARNING Read and understand all instructions. Failure to follow all instructions listed below may result in serious personal injury.

When using the extension pole to cut the branches on a tree, make sure to keep a firm footing and balance. Do not stand in a position where the branch may land after being cut.
When using this machine with the extension pole, make sure to insert the battery pack to the pole firstly.

COMPONENT LIST

TECHNICAL DATA

FIG 10 TECHNICAL DATA.JPG

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the instruction book carefully as well as the instruction book of Pruning Saw WG324.

This extension pole is designed for use with Worx Pruning Saw WG324 series.

ASSEMBLY
WARNING: Before attaching the extension pole, make sure that the battery pack has been removed.

(1) ASSEMBLING THE EXTENSION POLE
Align and insert the handle of extension pole into the shaft. Rotate the Locking Knob clockwise to lock. (See Fig. A1, A2)

NOTE: Make sure that the shaft is firmly locked in place.

(2) ASSEMBLING THE EXTENSION POLE TO THE MACHINE (See Fig. B1, B2)

Step 1: Align and insert the extension pole into the saw.
Step 2: Hang the buckle on the hook of the saw. Press the Clamping Lever to tighten the extension pole to the machine.

NOTE: Make sure the extension pole is locked into position securely before operation.

(3) REMOVING THE EXTENSION POLE (See Fig C)
Loosen the Clamping Lever to release the buckle.
Press the Extension Pole Release Button to disconnect the extension pole with the saw.

WARNING! When using this machine with the Extension Pole, make sure that the battery pack has been removed.

WARNING! ELECTROCUTION HAZARD
Never use the pruning saw or extension pole in an area with overhead power lines or where the branch being cut can come into contact with overhead power lines.

CUTTING WITH EXTENSION POLE

Attached the pole as described in “Assembly”.
Install the battery pack into the machine.
NOTE: Your battery pack maybe UNCHARGED and you must charge it before usage. Depress the battery pack release button to remove the battery pack from your tool (See Fig. D1). After recharging, insert the battery pack into the battery port. A simple push and slight pressure will be sufficient until a click is heard (See Fig. D2). Check to see if the battery is fully secured.
NOTE: When removing the battery pack, hold it firmly to avoid dropping and injury.
Before cutting a high branch, consider all the same points detailed in the previous section “Trimming Branches” but pay particular attention to the likely path of the falling branch.
**** WARNING: Do not stand directly below a branch being cut. Keep bystanders far away. Do not stand on a ladder or other type of unstable support while using the tool. Do not use the tool near cable, electrical power or telephone lines. Keep 3m away from all power lines. (See Fig. E1-E4)
Use both hands to grip Pole Saw. Use only designated grip areas when operating Pole Saw (See Fig. E5). Use firm grip. Thumbs and fingers must wrap around Pole Saw handle and pole.
Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet.
When ready to make a cut, press the Lock-out Button, then fully press the On/off Switch (See Fig. E6). This will turn Pole Saw on. Releasing On/ off Switch will turn Pole Saw off. Make sure saw is running at full speed before starting a cut.
When starting a cut, place moving chain against wood. Hold Pole Saw firmly in place to avoid possible bouncing or skating (sideways movement) of saw.
Guide Pole Saw using light pressure. Do not force Pole Saw. The motor will overload and can burn out. It will do the job better and safer at the rate for which it was intended.
Remove Pole Saw from a cut with saw running at full speed. Stop Pole Saw by releasing trigger. Make sure chain has stopped before setting Pole Saw down.