FS M6200 Series Multi Service WDM Optical Transport Platform User Guide

: June 10, 2024
: FS

FS M6200 Series Multi-Service WDM Optical Transport Platform

FS-M6200-Series-Multi-Service-WDM-Optical-Transport-Platform-
PRODUCT

Product Information

M6200 Series WDM Network

The FS M6200 Series Platform is a managed, flexible, and scalable architecture for fiber networks. It can support EDFA, OEO, OLP, DCM, and other M6200 Series Infrastructure Modules to construct a multi-service optical transmission network platform.

The M6200 Series Infrastructure Modules are designed as 1-slot card type or 2-slot card type to match the managed chassis. The 1-slot module includes OEO, DWDM EDFA, OLP, DWDM Red/Blue Filter, DCM(40km), OSC, NMU, etc. The 2-slot module includes MUX, DEMUX, and DCM(80km).
The M6200 Series Managed Chassis is available in two types: M6200-CH2U and M6200-CH5U. The M6200-CH2U has seven chassis slots, and the M6200-CH5U has 15 chassis slots.
The product comes with accessories including power cords, console cables, Ethernet cables, mounting brackets, cable managers, ESD wrist straps, grounding cables, and M6 screw sets.

Product Usage Instructions

Before powering on the M6200 Series WDM Network, ensure that all cables are properly connected and the modules are installed correctly in the chassis.
Connect the power cords to the M6200 Series Managed Chassis and plug them into a power outlet.
Connect a console cable and an Ethernet cable to the M6200 Series Managed Chassis to configure the device.
Use the NMU (Network Management Unit) to manage and monitor the M6200 Series WDM Network.
The M6200 Series Infrastructure Modules can be used to construct a multi-service optical transmission network platform. Refer to the product manual for specific usage instructions on each module.
If any alarm appears on the device, consult the product manual to troubleshoot the issue.
If the fan unit needs to be replaced, follow the instructions in the product manual and finish the operation within two minutes to avoid overheating.

For more detailed information on the installation, configuration, and usage of the M6200 Series WDM Network, refer to the product user manual.

Introduction

FS M6200 Series Platform provides a managed, flexible and scalable architecture for fiber networks. It can support EDFA, OEO, OLP, DCM and other M6200 Series
Infrastructure Modules to construct a multi-service optical transmission network platform.

M6200 Series Platform Overview

M6200 Series Infrastructure Modules

Slot Card Type

NOTE:

M6200 series modules are designed as 1-slot card type or 2-slot card type to match the managed chassis.
1-slot module: OEO, DWDM EDFA, OLP, DWDM Red/Blue Filter, DCM(40km), OSC, NMU, etc.
2-slot module: MUX, DEMUX, DCM(80km).

M6200 Series Managed Chassis

Chassis Type	Chassis Slot
M6200-CH2U	7pcs
M6200-CH5U	15pcs

Accessories

FS-M6200-Series-Multi-Service-WDM-Optical-Transport-
Platform-FIG-5 FS-M6200
-Series-Multi-Service-WDM-Optical-Transport-Platform-
FIG-6

DWDM Mux Demux Module

FS-M6200-Series-Multi-Service-WDM-Optical-
Transport-Platform-FIG-7

Front Panel Port

Port	Port Type	Description
C21-C60	LC/UPC	Mux/Demux Channel Port
OUT	Optical Singal Output Port
IN	Optical Singal Input Port
MON	Input/Output Optical Power Monitoring Port

DWDM EDFA (Erbium Doped Fiber Ampliﬁer)

Front Panel Port

Port	Port Type	Description
VOA Port	SFP	Optical Power Attenuation Adjusting Port for SFP VOA
OUT	LC/UPC	Optical Signal Output Port
IN	Optical Signal Input Port
OSCO	Optical Supervisory Channel Output Port
OSCI	Optical Supervisory Channel Input Port
MON	Optical Signal Monitoring Port
CONSOLE	Micro USB	Debugging & Upgrading Port

Front Panel LED

LED	Alarm State	Normal State	Description

ALM

| Always-ON:

There is an alarm of the power supply, the fan, or the NMU module.

| Light OFF| Module State Alarm
Quick Flash:

The module type does not match.

RUN| Always OFF:

The module is not normally enabled.

| Slow Flash| Module Run
IN| Always Red:

There is a LOS alarm at the port.

| Always Green| Input Optical Power Alarm
OUT| Always OFF:

The port is not enabled.

10G OEO Transponder

Front Panel Port

Port	Port Type	Description
Port 1~10	SFP/SFP+	Optical Transceiver Signal Transmitting Port

Front Panel LED

LED	Status	Description
SYS	Slow Flash of Green Light	There is no alarm of the module.
Quick Flash of Red Light	The module type does not match.
Slow Flash of Red Light	There is alarm of the module.
Always Red	The module is enabling.
1~10	Always Green	There is no LOS alarm of the port.
Always Red	There is LOS alarm of the port.
Always OFF	The port is disabled.

Signal Protocol

Service	Type	Rate
STM-1

SDH Service

SAN Service

Ethernet Service

100G OEO Transponder

Front Panel Port

Port	Port Type	Description
Port 1~6	QSFP+/QSFP28	40/100Gbps Optical Transceiver Signal

Transmitting Port

Front Panel Port

LED	Status	Description

ALM

1~6

DCM (Dispersion Compensation Module)

Front Panel Port

OSC Module (Optical Supervisory Channel Module)

Front Panel Port

Port	Port Type	Description
IN1/2

LC/UPC

| Transmission Line Side Optical Singal Input Port
OUT1/2| Transmission Line Side Optical Singal Output Port
OSCI1/OSCI2| Optical Supervisory Channel Input Port
OSCO1/OSCO2| Optical Supervisory Channel Output Port
TX1/2| WDM Demultiplexing Optical Singal Input Port
RX1/2| WDM Multiplexing Optical Singal Output Port

1+1 OLP (Optical Line Protection)

Front Panel Port

Port	Port Type	Description
TX/RX

LC/UPC

| Input/Output Port Connected to the Transmission Equipment
T1/R1| Main Optical Signal Transmitting Port/Receiving Port
T2/R2| Backup Optical Signal Transmitting Port/Receiving Port
CONSOLE| Micro USB| Debugging & Upgrading Port

Panel Key Instruction

Key	Function	Description
AUTO/FORCE	Press for switching auto mode or manual mode	Switching

Working Mode
PRI/SEC| Press for switching work channel of primary/second state| Switching Working Channel

Front Panel LED

LED	Status	Description

ALM

Managed Chassis

FS-M6200-Series-Multi-Service-WDM-Optical-Transport-
Platform-FIG-13

Front Panel Port

Slots	Description
NMU Module	Network Management Unit(NMU), the main control module of

chassis
Blank Plate 1| Used for 1+1 NMU module backup or M6200 series business module
Blank Plate 2~7| Used for 1-slot/2-slot M6200 series business module
Fan| Support field-replacedable and hot-swappable
AC Power| AC power supply, 90VAC~264VAC, 45Hz~65Hz, supports 1+1 backup

FS-M6200-Series-Multi-Service-WDM-Optical-Transport-Platform-
FIG-14

Front Panel Port

Slots	Description
NMU Module	Network Management Unit(NMU), the main control module of

chassis
Blank Plate 1| Only used for 1+1 NMU module backup
Blank Plate 2~15| Used for 1-slot/2-slot M6200 series business module
Fan| Support field-replacedable and hot-swappable
AC Power| AC power supply, 110VAC~260VAC, 45Hz~65Hz, supports 1+1 backup

Networking Management Unit

FS-M6200-Series-Multi-Service-WDM-Optical-
Transport-Platform-FIG-15

Front Panel Port

Port	Port Type	Rate	Description

MGMT 1~4

|

RJ45 ETH

|

10/100M

Auto-negotiate

| 1 Connect to the local network management computer

2 Interface for NMS concatenation equipment

MGMT5~6| SFP| 100M| Out of band OSC management
CONSOLE| RJ45 ETH| /| Debugging & Upgrading port

Front Panel LED

LED	Status	Description

ALM

ACT

| Always ON| The module is the primary module.
Always OFF| The module is the secondary module.

Site Environment

Keep the equipments indoors. If it is in rainy season or in humid environment, dehumidiﬁcation measures must be taken.
Ensure there is no water on the storage ﬂoor and no leakage to the packing box of the equipment.
Avoid automatic ﬁre ﬁghting facilities, heating system and other places where leakage may occur.

Installing

Wearing ESD Wrist Strap

Before touching any device or module, wear an ESD wrist strap or ESD gloves to protect sensitive components against electrostatic discharge from the human body.
Connect other end of the ESD wrist strap to the PGND point on the chassis.

Installing Business Module

FS-M6200-Series-Multi-Service-WDM-Optical-
Transport-Platform-FIG-18

Hold the ejector levers on the front panel of the module and raise them.
Push the module gently along the guide rail until the module cannot go any further. Then lower the two ejector levers of the module.

Installing Mounting Brackets

Secure the mounting brackets to the two sides of the M6200 series managed chassis with 8x M4 screws.

Rack Mounting

Put the M6200 series managed chassis on the shelf in the cabinet.
Install and tighten the panel with 4 sets of M6 screws.
Cable manager can be installed together with mounting brackets to the cabinet.

Grounding the M6200 Series Managed Chassis

Secure the grounding lug to the grounding point on the chassis front panel with the washers and screws.
Connect the other end of the cable to a proper earth ground, such as the rack in which M6200 series is mounted.

CAUTION: The earth connection must not be removed unless all supply connections have been disconnectsd.

Connecting Power Cord

Plug AC power cord into the power port on the front panel of AC power module.
Connect the other end of the power cord to an AC power source.

WARNING: Do not install power cables while the power is on.

Connecting to the Management Ports

SFP Management Port

Plug the compatible SFP transceiver into the SFP port on the front of NMU module.
Connect a fiber optic cable to the transceiver. Then connect the other end of the cable to another fiber device, such as a switch.

RJ45 Management port

Connect one end of the standard RJ45 Ethernet cable to the MGMT1&2 port on the front of NMU module.
Connect the other end of cable to a computer.

NOTE:

SFP management port is designed for long-haul management more than 100m.
RJ45 management port is designed for short-haul management less than 100m.
You can start your management by selecting one cf the above six management ports.

Configuring the M Series Platform

Configuring the M Series Platform Using the Web-based lnterface

Step 1: Connect your computer with the network cable to any Ethernet MGMT port of the NMU module.
Step 2: Get the NMS software from the CD of chassis accessories or download the file “NMS software” online, and then install it.
Step 3: Double Click “NMS Server” icon on the desktop and the dialogue box of license validation will pop up. Enter the license key (included in the CD) to finish validation. (If you can’t find the license key, please contact FS sales manager for help.)
Step 4 : Then the NMS server interface pops up. Double click “Start NMS Server” to run the server, when it prompts “Please connect your client to the web server on port: 9090”, it means that you have successfully started the NMS server. And then you can close the NMS Server window, the server is still running in the background.
Step 5: Open a browser window. (Recommend IE11.0 and above version or Google Chrome browser).
If you log in from local NMS host, enter localhost:9090 in the address bar to open the login interface.
If you log in from other remote host, enter the server IP address XXX.XXX.XXX.XXX:9090 (IP address of NMS server) to open the login interface.
Step 6: Enter correct user name and password (For the administrator, the default login user name is “root”, and the default password is “public”), as shown in the ﬁgure below:
Step 7 : Click login, you are now ready to conﬁgure M series platform

NOTE: Refer to the M SERIES NETWORK MANAGEMENT USER MANUAL online for further information

Troubleshooting

Module LEDs Working Abnormally

Check the power cable connections at the M6200 series managed chassis and the power source.
Make sure that all cables are used correctly and comply with the power speciﬁcations.
Make sure that business modules are in the right position in the M6200 series managed chassis.

Accessing the Web-based Configuration Page Unsuccessfully

Check MGMT ports LED on the NMU module and make sure the Ethernet cable is connected properly.
Try another port on the NMU module and make sure the Ethernet cable is suitable and works normally..
Pow M6200 series managed chassis. After a while, power it on again.
Make sure the IP address of your NMS server is correctly configured.
usiness Module Cannot Be Added

Enter through CMD.

Ping business module IP to check whether it can communicate.
Check whether normal communication can be made between business module and NMU module.
Change another business module.

Online Resources

Download https://www.fs.com/download.html
Help Center https://www.fs.com/service/help_center.html
Contact Us https://www.fs.com/contact_us.html

Product Warranty

FS ensures our customers that any damage or faulty items due to our workmanship, we will o er a free return within 30 Days from the day you receive your goods. This excludes any custom made items or tailored solutions.
Warranty: M6200 series enjoy 2 years limited warranty against defect in materials or workmanship. For more details about warranty, please check at : https://www.fs.com/policies/warranty.html
Return: If you want to return item(s), information on how to return can be found at: h ttps://www.fs.com/policies/day_return_policy.html

FCC

Compliance Information

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
Responsible party (only for FCC matters)
FS.COM Inc.
380 Centerpoint Blvd, New Castle, DE 19720, United States https://www.fs.com
FS.COM GmbH hereby declares that this device complies with Directive 2014/30/EU. A copy of the EU Declaration of Conformity is available at
www.fs.com/company/quality_control.html
FS.COM LIMITED
24F, Infore Center, No.19, Haitian 2nd Rd, Binhai Community, Yuehai Street, Nanshan District, Shenzhen City
FS.COM GmbH
NOVA Gewerbepark Building 7, Am
Gfild 7, 85375 Neufahrn bei Munich, Germany
Copyright © 2021 FS.COM All Rights Reserved.