FS VMS-201C Video Management Server User Guide

: October 30, 2023
: FS

Table of Contents

Introduction
Accessories
Hardware Overview
- Front panel LEDs
- Back Panel Ports
Installation
- Rack Mounting
Configuring the switch
Online Resources
Product Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FS VMS-201C Video Management Server

VMS-201C

Introduction

Thank you for choosing Video Management Server. This guide is designed to familiarize you with the structure of the Server and describes how to deploy the Server in your network.

FS VMS-201C Video Management Server

Accessories

External power cord x1
High-speed signal cable x1
Common electronic cable x1
Mouse x1
Mounting bracket component x1
Sheet metal component x1
Cable connection terminal x6

Hardware Overview

Front panel LEDs

Hardware Overview

LEDs	State	Description
RUN	Steady on	Normal.
Blinking	Starting up.
ALM	Steady on	Device alarm.
NET	Steady on	Connected to network.
HDD	Off	No hard disk, or disk is not connected to power.
Steady on	No data reading or writing.
Blinking	Reading or writing data.

Back Panel Ports

Hardware Overview

Ports	Description
ACT	Network interface, used to connect an Ethernet network switch
RS485	Serial port, used to interoperate with the connected device
RS232	Serial interface, used to debug and maintain the device
USB3.0	Used to connect USB devices such as USB flash drive, USB mouse

and USB keyboard
e-SATA| Used to connect an e-SATA disk
HDMI| HDMI output, used to connect HDMI interface on a display device
VGA| VGA output, used to connect the VGA interface on a display device
ALARM IN| 24-channel alarm input, used to connect alarm devices such as a magnetic door sensor
ALARM OUT| 8-channel alarm output, used to connect alarm devices such as an alarm siren or alarm lamp
GND| The 12V (rightmost pin) is the power output
Power supply| 220AC power input
ON/OFF| Power switch
Grounding point| Grounding terminal

Installation

Please follow the steps if disk installation is necessary. The illustrations are for reference only.

NOTE: Please use the SATA disks recommended by the manufacturer. Disconnect power before installation.

Preparation

Prepare a PH2 Philips screwdriver.
Prepare an antistatic wrist strap or antistatic gloves during the installation.

Disk Installation

Installation

Loosen the screws on the rear panel and side panel and remove the upper cover.
Attach the 4 gaskets on the brackets.
Secure the disk on the brackets by using fixing screws.
Connect one end of the data cable and power cable to the hard disk.
Place the disk in the chassis and secure it with 4 fixing screws (M3*5).
Connect the other end of the data cable and power cable to the motherboard.

Rack Mounting

Installation

Install the device on a well grounded and securely installed rack. First install two mounting brackets on the device, and then secure the device on the rack by threading screws through the holes on the mounting brackets.

Configuring the switch

Start up

Please prepare a monitor and a keyboard. Connect the monitor, mouse, keyboard and then power.
Turn on the power switch on the back panel. The startup takes a while. Please wait patiently.

Login

Configuring the switch

When the device is started, the login page appears. Use the default username admin and default password 123456 to log in to the software client. The software client is mainly used for service operations. Click the help link in the top right corner for help information. When logged in, you can click the Web icon in the top right corner to access the Web client. The Web client is mainly used for management and configuration purpose. Click the toolbar at the bottom to switch between the software client and Web client.

Restart

Right-click on the software client and then choose Restart, or access the Web client and click Restart on S **ystem Configuration

Maintenance>Maintenance.**

Shutdown

Use the power switch on the back panel to shut down the device.

Online Resources

Download https://www.fs.com/products_support.html
Help Center https://www.fs.com/service/fs_support.html
Contact Us https://www.fs.com/contact_us.html

Product Warranty

FS ensures our customers that any damage or faulty items due to our workmanship, we will offer a free return within 30 days from the day you receive your goods. This excludes any custom made items or tailored solutions.

Warranty: The Video Management Server enjoys a 2-year limited warranty against defect in materials or workmanship. For more details about warranty, please check at: https://www.fs.com/policies/warranty.html

Return: If you want to return item(s), information on how to return can be found at: https://www.fs.com/policies/day_return_policy.html

Q.C. PASSED