TECH CONTROLLERS EU-C-2N Sensor Instruction Manual
- June 9, 2024
- TECH CONTROLLERS
Table of Contents
USER’S MANUAL
EU-C-2N
WARRANTY CARD
TECH company ensures to the Buyer proper operation of the device for the
period of 24 months from the date of sale. The Guarantor undertakes to repair
the device free of charge if the defects occurred through the manufacturer’s
fault. The device should be delivered to its manufacturer. Principles of
conduct in the case of a complaint are determined by the Act on specifi c
terms and conditions of consumer sale and amendments of the Civil Code
(Journal of Laws of 5 September 2002).
CAUTION! THE TEMPERATURE SENSOR CANNOT BE IMMERSED IN ANY LIQUID (OIL ETC).
THIS MAY RESULT IN DAMAGING THE CONTROLLER AND LOSS OF WARRANTY! THE
ACCEPTABLE RELATIVE HUMIDITY OF THE CONTROLLER’S ENVIRONMENT IS 5÷85% REL.H.
WITHOUT THE STEAM CONDENSATION EFFECT. THE DEVICE IS NOT INTENDED TO BE
OPERATED BY CHILDREN.
Activities related to setting and regulation of the controller parameters
described in the Instruction Manual and parts wearing out during normal
operation, such as fuses, are not covered by warranty repairs. The warranty
does not cover damages arising as a result of improper operationor through the
user’s fault, mechanical damage or damage created as a result of fire, flood,
atmospheric discharges, overvoltage or short-circuit. The interference of an
unauthorized service, wilful repairs, modifications and construction changes
cause the loss of Warranty. TECH controllers have protective seals. Removing a
seal results in the loss of Warranty.
The costs of unjustifiable service call to a defect will be borne exclusively
by the buyer. The unjustifiable service call is defined as a call to remove
damages not resulting from the Guarantor’s fault as well as a call considered
unjustifiable by the service
after diagnosing the device (e.g. damage of the equipment through the fault of
the client or not subject to Warranty), or if the device defect occurred for
reasons lying beyond the device.
In order to execute the rights arising from this Warranty, the user is
obliged, at his own cost and risk, deliver the device to the Guarantor along
with a correctly filled-in warranty card (containing in particular the sale
date, the seller’s signature and a description of the defect) and sales proof
(receipt, VAT invoice, etc.). The Warranty Card is the only basis for repair
free of charge. The complaint repair time is 14 days.
When the Warranty Card is lost or damaged, the manufacturer does not issue a
duplicate.
…………..seller’s stamp …………… ………………..date of sale………………
Safety
Before using the device for the fi rst time the user should read the following
regulations carefully. Not obeying the instructions included in this manual
may lead to personal injuries or controller damage. The user’s manual should
be stored in a safe place for further reference. In order to avoid accidents
and errors it should be ensured that every person using the device has
familiarized themselves with the principle of operation as well as security
functions of the controller. If the device is to be sold or put in a diff
erent place, make sure that the user’s manual is there with the device so that
any potential user has access to essential information about the device.
The manufacturer does not accept responsibility for any injuries or damage
resulting from negligence; therefore, users are obliged to take the necessary
safety measures listed in this manual to protect their lives and property.
We are committed to protecting the environment.
Manufacturing electronic devices imposes an obligation of providing for
environmentally safe disposal of used electronic components and devices.
Hence, we have been entered into a register kept by the Inspection For
Environmental Protection. The crossedout bin symbol on a product means that
the product may not be disposed of to household waste containers. Recycling of
wastes helps to protect the environment.The user is obliged to transfer their
used equipment to a collection point where all electric and electronic
components will be recycled.
Description
EU-C-2N sensor is intended to be installed on the windows of particular heating zones. When the window is opened, the sensor sends the information to the main controller which deactivates heating in the zone after a pre-set delay time.
Technical data
Power supply…………………………………………………..batterie ER14250
Operation temperature…………………………………………………..5-50°C
Operation frequency…………………………………………………….868 MHz
Ambient humidity………………………………………………………….5-85%
Installation
In order to install EU-C-2 sensor, place double-sided tape on the upper part of the window frame (not where the hinges are located) and stick the back of the sensor to the tape. Next, put the front part of the sensor in its place. The installation method is illustrated in the picture below.
NOTE
The magnet should be placed on the window casement!
Maximum distance between the sensor and magnet up to 15 mm.
Sensor registration
Once ‘Registration’ function in the main controller has been activated, press
quickly the communication button on a given EU-C-2N sensor.
If the registration attempt has been successful, the main controller will
display an appropriate message and the control light on EU-C-2N sensor will fl
ash twice.
If the control light goes on permanently, there is no communication with the
main controller.
- casing
- antenna
- battery
- montage axle, position of the sensor relative to the magnet
- registration button
- casing
- magnet
EU Declaration of Conformity
Hereby, we declare under our sole responsibility that EU-C-2N manufactured by
TECH STEROWNIKI, head-quartered in Wieprz Biała Droga 31, 34-122 Wieprz, is
compliant with Directive 2014/53/EU of the European parliament and of the
Council of 16 April 2014 on the harmonisation of the laws of the Member States
relating to the making available on the market of radio equipment, Directive
2009/125/EC establishing a framework for the setting of ecodesign requirements
for energy-related products as well as the regulation by the MINISTRY OF
ENTREPRENEURSHIP AND TECHNOLOGY of 24 June 2019 amending the regulation
concerning the essential requirements as regards the restriction of the use of
certain hazardous substances in electrical and electronic equipment,
implementing provisions of Directive (EU) 2017/2102 of the European Parliament
and of the Council of 15 November 2017 amending Directive 2011/65/EU on the
restriction of the use of certain hazardous substances in electrical and
electronic equipment (OJ L 305, 21.11.2017, p. 8).
For compliance assessment, harmonized standards were used: PN-EN IEC 60730-2-9
:2019-06 art. 3.1a Safety of use
PN-EN 62479:2011 art. 3.1 a Safety of use
ETSI EN 301 489-1 V2.2.3 (2019-11) art.3.1b Electromagnetic compatibility
ETSI EN 301 489-3 V2.1.1:2019-03 art.3.1 b Electromagnetic compatibility
ETSI EN 300 220-2 V3.2.1 (2018-06) art.3.2 Effective and coherent use of radio
spectrum
ETSI EN 300 220-1 V3.1.1 (2017-02) art.3.2 Effective and coherent use of radio
spectrum
Wieprz, 20.11.2020
Central headquarters:
ul. Biafa Droga 31, 34-122 Wieprz
Service:
ul. Skotnica 120, 32-652 Bulowice
phone: +48 33 875 93 80
e-mail: serwis@techsterowniki.pl
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>