PHILIPS BDS/BSS639 CitySwan LED gen3 User Manual
- June 9, 2024
- Philips
Table of Contents
PHILIPS BDS/BSS639 CitySwan LED gen3
Product Information: Cit ySwan LED gen3 BDS/BSS639
- Voltage: 220V outdoor/240V
- Frequency: 50Hz/60Hz
- IP Rating: IP66
- IK Rating: IK08
- Compliance: R&TTE
- LEDs: LED40 40, LED50 40, LED60 40, LED70 40, LED80 64, LED90 64, LED100 64, LED110 64, LED120 64, LED130 64, LED140 64
- Energy Class: 722/E for BDS models and 727/D, 730/D, 740/C, 830/E** for BSS models
- Max Number of Luminaires on MCB 16A Type B: Varies by model and driver (FP/SR)
- Inrush Current: Varies by model and driver (FP/SR)
- Weight: Varies by model
- Light Distribution: Asymmetric and Symmetric
- Dimensions: Varies by model and installation method (suspended/wire)
Product Usage Instructions: Cit ySwan LED gen3 BDS/BSS639
- Before installation or maintenance, disconnect the voltage supply.
- Refer to the product label for specific safety instructions in your language.
- Select the appropriate model based on your lighting needs and installation method (suspended/wire).
- Follow the installation instructions provided with the product, ensuring the luminaire is securely fastened and aligned properly.
- Connect the luminaire to the voltage supply, following local wiring regulations and the instructions provided with the product.
- Test the luminaire to verify proper function before use.
- For maintenance or replacement of the light source, control gear, or external flexible cable, contact the manufacturer or their service agent or a similar qualified person.
Note : Product specifications are subject to change without notice. Keep this user manual for future reference and visit www.philips.com/lighting for updates.
Max number of luminaires on MCB 16A type B with resp FP/SR driver
Energy class of the light source
For products with TAG Label
To get an overview of all spare parts for a luminaire, please refer to detailed instructions in the service manual available via the Signify Service tag apps (Android and iOS). To program a spare driver is supported by Signify Service tag (Android only)
Disconnect before servicing
Luminaire has basic insulation between Low Voltage supply and control
conductors.
The light source and/or control gear and/or the external flexible cable
contained in this luminaire shall only be replaced by the manufacturer or his
service agent or a similar qualified person.
Storage, installation, use, operation and maintenance of the products needs to
be performed exactly according the instructions in this manual and/or other
instructions as may be provided by us to guarantee safe use of the product
over its entire lifetime. Failure to adhere to these instructions will
invalidate your to warranty. Bolts with indication of torque strength on the
drawing need to be tightened using a calibrated torque wrench. Pre-assembled
bolts to be retightened again to the required torque specification to assure
maximum strength over lifetime.
Zhaga-D4i and SR certified compatibility – For Zhaga-D4i/SR-Certified based
luminaires only Zhaga-D4i/SR-Certified components/sensors are to be used (see
also: https://www.zhagastandard.org/products /
https://www.lighting.philips.co.uk/oem-emea/products/driving-connected-
lighting). The functional compatibility of two SR-certified and/or Zhaga-D4i
controllers/sensors to be used in combination, as well as the override
possibility of any line-switch function used in an SR-based/Zhaga-D4i
luminaire, is to be released by the master controller/sensor supplier. If
using a NEMA 7-pin socket on an SR-based luminaire, a full system verification
is required. Not following this advice can/will cause risk of damage and non-
compliance for which Signify cannot take any responsibility.
© 2020 Signify Holding
All rights reserved. This document contains information relating to the
product portfolio of Signify which information may be subject to change. No
representation or warranty as to the accuracy or completeness of the
information included herein is given and any liability for any action in
reliance thereon is disclaimed. The information presented in this document is
not intended as any commercial offer and does not form part of any quotation
or contract. Philips and the Philips Shield Emblem are registered trademarks
of Koninklijke Philips N.V.. All other trademarks are owned by Signify Holding
or their respective owners.
Signify Holding
The Netherlands
References
- Sustainable LED lighting solutions | Philips lighting
- Sustainable LED lighting solutions | Philips lighting
- Sustainable LED lighting solutions | Philips lighting
- Driving connected lighting | Philips lighting
- Products
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>