Hanwha Techwin SMT-2212 Security Led Monitor User Manual
- June 9, 2024
- Hanwha Techwin
Table of Contents
SECURITY LED MONITOR
User Manual
Security LED Monitor
Copyright
©2022 Hanwha Vision Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other
trademarks mentioned in this manual are the registered trademark of their
respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document
shall be reproduced, distributed or changed, partially or wholly, without
formal authorization.
Disclaimer
Hanwha Vision makes the best to verify the integrity and correctness of the
contents in this document, but no formal guarantee shall be provided.
Use of this document and the subsequent results shall be entirely on the
user’s own responsibility. Hanwha Vision reserves the right to change the
contents of this document without prior notice.
※ Design and specifications are subject to change without prior notice.
overview
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit.
Follow all the safety instructions listed below.
Keep these operating instructions handy for future reference.
-
Read these instructions.
-
Keep these instructions.
-
Heed all warnings.
-
Follow all instructions.
-
Do not use this apparatus near water.
-
Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.
(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.) -
Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.
-
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
-
Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. if the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
-
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
-
Only use attachments/accessories specified by the manufacturer.
-
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
-
****Unplug this apparatus during lightning storms or when unused for long periods of time.
-
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Standards Approvals
- Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
BEFORE START
You have to keep in mind the following notices :
- Hanwha Vision retains the copyright on this manual.
- This manual cannot be copied without Hanwha Vision’s prior written approval.
- We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of instructions mentioned in this manual.
- Contact the retailer for troubleshooting help.
SAFETY INSTRUCTIONS
Power
Do not use a damaged power cord or plug or a damaged or loose power outlet.
~ Otherwise, this may result in electric shock or fire.| Do not touch the
power plug with wet hands when removing or plugging the plug into the outlet.
~ Otherwise, this may result in electric shock| Make sure to connect the power
cord to a grounded power outlet.
~ Otherwise, it may result in electric shock
or personal injury.
Ensure that the power plug is
plugged into the power outlet firmly
and correctly.
~ Otherwise, this may result in fire.| Do not forcefully bend or pull the
power plug and do not place any
heavy material on it.
~ Otherwise, this may result in fire.| Do not connect multiple appliances to
the same power outlet.
~ Otherwise, this may cause fire due to overheating.
Do not disconnect the power cord
while using the product.
~ Otherwise, this may result in damage to
the product due to electric shock.| To disconnect the apparatus from
the mains, the plug must be pulled
out from the mains socket, therefore
the mains plug shall be readily
operable.
~ Otherwise, this may cause electric shock
or fire.| Use only the power cord provided by our company. Do not use the
provided power cord of another product.
~ Otherwise, this may result in fire or electric shock.
Connect the power plug to a wall
outlet that can be easily reached.
~ When a problem occurs with the product,
you must unplug the power plug to cut the power off completely. You cannot
cut the power off completely using only the power button on the product.| |
Installation
Ensure that at least two persons liftand move the product.
~ Otherwise, it may be dropped and causepersonal injury, and/ or damage the
product.| When installing the product in a cabinet or rack, make sure that
the front end of the bottom of the product does not project out.
~ Otherwise, it may fall or cause personal
injury.
~ Use a cabinet or rack of a size appropriateto the product.| Do not place
candles, mosquito repellant, cigarettes and any heating appliances near the
product.
~ Otherwise, this may result in fire.
Keep heating appliances as far away
from the power cord or the product
as possible.
~ Otherwise, this may result in electric
shock or fire.| Do not install it in a badly ventilated
location such as a bookcase or
closet.
~ Otherwise, this may result in fire due to an
increase in the internal temperature.| When putting the product down, make
sure to put it down softly.
~ Otherwise, this may result in damage to
the screen display.
Do not place the front of the product
on the floor.
~ Otherwise, this may result in damage to
the screen display.| Ensure that an authorized installationcompany installs
the wall mount.
~ Otherwise, it may fall and cause personal
injury.
~ Make sure to install the specified wall
mount.| Install your product in a well
ventilated location. Ensure that there
is a clearance of more than 4 inches
(10 cm) from the wall.
~ Otherwise, it may result in fire due to an
increase in the internal temperature.
Ensure that the packaging vinyl is
kept away from children.
~ Otherwise, it may result in serious harm
(suffocation) if children play with it.| If the height of your monitor is
adjustable, do not place any object
or part of your body on the stand
when lowering it.
~ This may cause damage to the product or
the person carrying it.|
Clean
Do not spray cleaner directly onto the surface of the product.
~ Otherwise, this may result in the discoloration and distortion of the
structure and the screen surface may peel off.| When cleaning the power plug
pins or dusting the power outlet, clean it with a dry cloth.
~ Otherwise, it may result in fire.| When cleaning the product, make sure to
disconnect the power cord.
~ Otherwise, it may result in electric shock or fire.
When cleaning the product, disconnect the power cord and clean it with a soft,
dry cloth.
~ (Do not use chemicals such as wax, benzene, alcohol, thinner, mosquito
repellant, lubricant, or cleaner.) These may change the appearance of the
product surface and peel off the indication labels on the product.| Since the
product housing is easilyscratched, make sure to use the
specified cloth only.| When cleaning the product, do not spray water directly
onto the main body of the product.
~ Ensure that water does not enter the product and that it is not wet.
~ Otherwise, this may result in electric shock, fire or a malfunction.
PACKAGE CONTENTS
Please unwrap the product, and place the product on a flat place or in the
place to be installed.
Please check the following contents are included in addition to the main unit.
Accessory category and quantity may differ depending on sales region.
NAMES AND FUNCTIONS OF EACH PART
Front
| Button | Description of functions |
|---|---|
| Panel key |
screen appears.
Press the [ 2 ] button to exit the screen adjustment menu. | Press the button while the menu screen is displayed to move the menu or adjust the value. If you press the button while the menu screen is not displayed, the
Back
| Name | Description of functions |
|---|---|
| 1 | HDMI |
| 2 | VGA |
| 3 | Power |
| 4 | Anti-theft lock |
Anti-theft Lock
- The locking device shape and locking method depend on the manufacturer. Please refer to the user guide provided with your anti-theft locking device for details.
- The following images are for reference only. Real-life applications may differ.
To lock an anti-theft locking device
- Fix the cable of your anti-theft locking device to a heavy object such as a desk.
- Put one end of the cable through the loop on the other end.
- Insert the locking device into the anti-theft lock slot at the back of the product.
- Lock the locking device.
- An anti-theft locking device can be purchased separately.
- Refer to the instruction manual supplied with the lock for detailed information on how to use it.
- You can purchase a lock at most stores specializing in electronics, or via the Internet.
Installation
Please take note of the followings before using this product.
- Do not use the product outdoor.
- Do not spill water or liquid in the connection part of the product.
- Do not impose the system to excessive shock or force.
- Do not pull out the power plug forcefully.
- Do not disassemble the product on your own.
- Do not exceed the rated input/output range.
- Use a certified power cord only.
- For the product with an input ground, use a grounded power plug.
BEFORE INSTALLING THE PRODUCT
Ventilation requirement
If the product is installed in a poorly ventilated area, it might be damaged
due to the temperature rising inside the product.
Ensure there is enough space around the product before installation.
Vertical wall mount condition
A. Minimum 40 mm
B. Ambient temperature Measuring point <35°C
Installation conditions for standing monitors
ASSEMBLING THE STAND
Before assembling the product, make sure that its screen is facing down when
placing it on a flat and safe surface.
Place the product on a soft cloth or product wrapping paper to protect it
before installation.
-
Assemble the base and neck of the stand.
-
Align the grooves on the neck with the grooves of the monitor, and attach them together.
For detaching the stand,
-
Press the button behind the monitor to detach the stand from the monitor.
-
Push the fixing hook on the stand base to detach the neck from the stand base.
INSTALLING WALL MOUNT PARTS
Installing Wall Mount Kits
The wall mount kit (sold separately) allows you to hang the product on a wall.
For more information on wall mounting, refer to the owner’s manual supplied
with the wall mount parts. When installing the wall mount, seek the help of a
technician.
Hanwha Vision is not responsible for any damage to the product or injury to
the user or others caused by any accident due to a user’s attempt to install
the product.
Wall Mount Kit Specifications (VESA)
-
Install the wall mount kit on a solid wall perpendicular to the floor.
-
Please refer to the nearest store when installing on other materials.
-
Installing on an inclined wall may cause the product to fall, which can result in serious injury.
-
When using a VESA mount, select a product that can hold 4 times the weight of the monitor.
-
When you purchase our wall mount kit, you will find a detailed installation guide and all parts required for assembly.
-
Do not use screws that are longer than the standard dimensions or that do not conform to the VESA standard screw specifications. Using screws that are too long may damage the inside of the product.
-
For wall mount parts that do not conform to the VESA standard screw specifications, the screw length may vary depending on the wall mount specifications.
-
Do not over-tighten the screws. The product may be damaged, or may fall, resulting in injury.
-
Hanwha Vision is not responsible for any damage to the product or injury to the user or others caused by any accident due to a user’s attempt to install the product.
-
Hanwha Vision is not responsible for damage to the product or injury to the user caused by using noncompliant or non-VESA wall mount parts, or by the customer not following the product installation instructions.
-
When hanging on a wall, two people should always lift the product.
-
The standard dimensions of the wall mount kit are shown in the table below. [Unit: mm]
Model name| *VESA dimensions (A B)| Standard screws|
Quantity**
---|---|---|---
SMT-2212| 100 × 100| M4/L8| 4
- Do not install the wall mount kit with the product turned on. This may lead to injury due to electric shock.
Connecting with other device
THINGS TO CHECK BEFORE CONNECTION
Check before connecting
- When connecting, refer to the instruction manual of the product to be connected. The number and position of external devices may differ depending on the product.
- Do not connect the power until all connections are complete. Connecting the power supply during connection may damage the product.
- Check the type of terminal behind the product you want to connect.
CONNECTING WITH EXTERNAL DEVICES
- Connect the power cable after all cables have been connected. Disconnect the power cable before connecting external devices.
- You can connect the product to external devices in various ways. Select the correct connection method for your external devices.
VGA (D-SUB) cable connection method
HDMI cable connection method
Menu settings
The screen adjustment menu can be set.
SCREEN (OSD) MENU SETTINGS
You can adjust menu settings by using the panel keys on the monitor.
- Press the [ 1 ] button to display the main menu.
- Press the < / > buttons to select the main menu, and then press the [ 1 ] button.
- Press the < / > buttons to select the sub-menu, and then press the [ 1 ] button.
- Press the < / > buttons to adjust the adjustment value.
- Press the [ 2 ] button to exit.
To return to the previous screen, press the [ 2 ] button.
- If you do not press any buttons for a certain period of time, the OSD menu screen will disappear.
- You can set the time up to 60 seconds in
; .
User : Red/Green/Blue values can be adjusted manually.
- Auto Adjust : Adjust the screen’s up and down / left and right ratio automatically. (Only available in VGA mode.)
- Color Adjust : Adjust the light and color of the monitor automatically. (Only available in VGA mode.)
VIDEO SETTINGS
Sets the screen brightness, color, etc.
- Press the [ 1 ] button to enter the main menu.
- Press the < / > button to select [ ] icon, and then press the [ 1 ] button.
• Contrast : Adjusts the difference in
brightness between the object and the environment.
• Brightness : Adjusts the brightness of the screen.
• Color Temp. : The color temperature can be adjusted and used depending on the monitor color.
You can select from Cool, Normal, Warm, User.
SCREEN SETTINGS
The screen’s size and position can be adjusted.
(The menu for screen settings is only available in VGA mode.)
- Press the [ 1 ] button to enter the main menu.
- Press the < / > button to select [ ] icon, and then press the [ 1 ] button.
• H.Position: Adjusts the position of the screen to the left or right.
• V.Position: Adjusts the position of the screen up or down.
• Clock: Adjusts the clock when it is too high.
• Phase: Adjusts the focus.
OSD SETTINGS
Sets up OSD values.
- Press the [ 1 ] button to enter the main menu.
- Press the < / > button to select [ ] icon, and then press the [ 1 ] button.
• Language : Select the screen language.
The initial value is set to .
• OSD H.Pos : Moves the screen of the menu to the left or right.
• OSD V.Pos : Moves the screen position of the menu up or down.
• OSD Timer : The menu screen disappears if the screen does not change for a certain period of time.
• Transparency : Sets the transparency of the menu screen.
SYSTEM SETTINGS
Configures the system.
- Press the [ 1 ] button to enter the main menu.
- Press the < / > button to select [ ] icon, and then press the [ 1 ] button.
• Mode : Select a screen mode appropriate
for your viewing environment.
– PC : A screen mode for PCs.
– Game : A screen mode appropriate for games.
– Movie : A screen mode appropriate for movies.
RESET
Resets the monitor settings to default.
Appendix
PRODUCT OVERVIEW
TROUBLESHOOTING
| Problems and Symptoms | Troubleshooting |
|---|---|
| The screen wars and disappears repeatedly. | • Check the cable connection |
between the product and the external deice. and check the locking status of me
connection deice.
The screen will not switch on.| • Confirm that the power cable s properly
connected.
The screen seems to be flowing darn.| • Check the cable connected to the
product
The screen is too bright. The screen is too dark| • Adjust the brightness and
contrast.
The product spontaneously turns itself off.| • Confirm that the power cable is
firmly connected to the product and tome power outlet.
The image on the screen appears strange.| • Video compression in scenes with
fast transitions. such as sports or action movies. can cause screen
distortion.
• Low signal level or poor quality may cause screen distortion. This is not a
product issue.
• Cellular phones within a 1 meter radius may cause interference with analog/
digital products.
The brightness and cola are strange.| • Adjust the screen option from the
brightness settings.
• Reset the screen wit the default screen settings.
I can see a dotted line on the edge of the screen.| • If the screen is the
original size. by changing it to 16:9.
I can see lines (red. green. blue) on the screen.| • This occurs due to a
fault in the DATA SOURCE DRNER IC of the monitor. Contact Hanivha Vision
Service Center to sohe the problem.
The screen is unstable and stops.| • Screen pauses may occur when the
resolution is different from the reanimenced resolution. a when the signal is
unstable. To sohe this problem. charge the resolution of the external deite to
the recommended resolution.
The image is not displayed on the full screen.| • Try adjusting the screen
size option of the product or external de ‘ e
The product smells of plastic.| • This is a normal smell. and will disappear
over time.
The monitor is titted to the We.| • Separate the stand from the axed and
reassemble it.
Hanwha Vision cares for the environment at all product manufacturing stages,
and is taking measures to provide customers with more environmentally friendly
products.
The Eco mark represents Hanwha Vision’s devotion to creating environmentally
friendly products, and indicates that the product satisfies the EU RoHS
Directive.
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment)
(Applicable in the European Union and other European countries with separate
collection systems)
This marking on the product, accessories or literature indicates that the
product and its electronic accessories (e.g. charger, headset, USB cable)
should not be disposed of with other household waste at the end of their
working life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate these items from other types of
waste and recycle them responsibly to promote the sustainable reuse of
material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they
can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product and its electronic
accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate
battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries
in this product should not be disposed of with other household waste at the
end of their working life. Where marked, the chemical symbols Hg, Cd or Pb
indicate that the battery contains mercury, cadmium or lead above the
reference levels in EC Directive 2006/66. If batteries are not properly
disposed of, these substances can cause harm to human health or the
environment.
To protect natural resources and to promote material reuse, please separate
batteries from other types of waste and recycle them through your local, free
battery return system.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>