Clarke SHY1 Safety Helmet Instruction Manual
- June 9, 2024
- Clarke
Table of Contents
SHY1 Safety Helmet
Instruction Manual
SAFETY HELMET
MODEL NO: SHY1(YELLOW)
PART NO: 8133824
**USER INSTRUCTIONS
**
INTRODUCTION
Thank you for purchasing this CLARKE Safety Helmet. Before using this product,
please read this manual thoroughly and follow the instructions carefully. In
doing so you will ensure your safety and you can look forward to your purchase
giving you long and satisfactory service.
The SHW1/SHY1 (white/yellow) helmets have been designed to provide head
protection to meet the requirements of PPE Regulation (EU) 2016/425 and
EN397:2012+A1:2012.
The helmet is not suitable as PPE for climbing activities, fire fighting,
sporting activities such as cycling, skiing, equestrian, motorcycling etc. The
helmet is not designed to protect from heat hazards such as molten metal.
This helmet has been tested to withstand the following risks:
- Impact protection – maximum force transmitted up to 5kN, within a temperature range of 50°C and -10°C
- Penetration by objects up to 3kg in weight, within a temperature range of 50°C and -10°C
MATERIALS DECLARATION
No parts of the helmet are made of materials that are known to cause skin
irritation. However, materials that come into contact with the skin can cause
allergic reactions to certain susceptible individuals.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can be
returned to us without prior permission.
This guarantee does not effect your statutory rights.
SAFETY PRECAUTIONS
The helmet should be checked each day before wearing to ensure that there are
no major surface defects such as crazing, cracks, deep scour marks,
discolouration or dents to the shell.
Never place this product on a hot surface.
FITTING AND ADJUSTMENT
For adequate protection the helmet must be adjusted to fit the user’s head
correctly. The helmet is adjustable for comfort and utility.
HEADBAND ADJUSTMENT
Horizontal headband adjustment is achieved by turning the adjuster.
Set the headband diameter with the adjustment knob.
Twist clockwise
to tighten and counterclockwise to loosen
- The head band size is from 5066cm.
CHIN-STRAP ADJUSTMENT
-
Set the buckle on each side to adjust the tension of the elastic chinstrap.
-
Take care to set both side equally.
PRODUCT CARE
CARE & MAINTENANCE
Inspect the helmet regularly to ensure optimum performance. Defects of the
helmet/headgear must result in immediate replacement. If the shell or headgear
show any defects, immediate disposal and replacement of the product is
recommended. Give particular attention to the harness attachment slots.
Significant impact to the helmet will result in reduced future protection,
even if visual physical deformation is not apparent. In any event, if any
cracks are detected, the helmet must be discarded immediately.
Do not apply tape, paint, solvents, adhesives or adhesive labels to the shell
as such application may reduce the effectiveness of the helmet.
CLEANING
The helmet can be wiped with soapy water or a household cleaning product when
dirty. Clean and/or disinfect all components regularly with a mild detergent
or disinfectant in luke warm water. Apply the cleaner with a clean cloth or
paper towel.
Do not use solvents for cleaning and always dry the helmet away from bright
sunlight or direct heat.
STORAGE
The helment should be transported and stored it its bag in cool, dry
conditions out of direct sunlight.
RECYCLING & THE ENVIRONMENT
If disposing of this product or any damaged components, do not dispose of with
general waste. This product contains re-usable raw materials. ABS plastic
products should be taken to your local civic amenity site for recycling into
new products.
COMPONENT PARTS
| 1 | Helmet shell |
|---|---|
| 2 | Central headstrap with attachments |
| 3 | Diagonal headstrap with attachments |
| 4 | Rear adjustable headband |
| 5 | Fixed headband with fabric sweatband |
| 6 | Chin piece |
| 7 | Chin-strap connector |
| 8 | Chin-strap elastic |
| 9 | Rear headband adjuster |
DECLARATION OF CONFORMITY – UKCA
DECLARATION OF
CONFORMITY – CE
A SELECTION FROM THE VAST RANGE OF
| QUALITY
PRODUCTS
AIR COMPRESSORS
From DIY to industrial, Plus air tools, spray guns and accessories.
GENERATORS
Prime duty or emergency standby for business, home and leisure.
POWER WASHERS
Hot and cold, electric and engine driven – we have what you need
WELDERS
Migy Arc,Tig and Spot. From DIY to auto/industrial.
METALWORKING
Drills, grinders and saws for DIY and professional use.
WOODWORKING
Saws, s anders, lathes, mortisers and dust extraction.
HYDRAULICS
Cranes, body repair kits, transmission jacks for all types of workshop use.
WATER PUMPS
Submersible, electric and engine driven for DIY, agriculture and industry.
POWER TOOLS
Angle grinders, cordless drill sets, saws and sanders. STARTERS/CHARGERS
All sizes for car and commercial use.| 
---|---|---
PARTS & SERVICE:
0208 988 7400
Parts Enquiries
Parts@clarkeinternational.com
Servicing & Technical Enquiries
Service@clarkeinternational.com
SALES: UK 01992 565333
Export 00 44 (0)1992 565335
Clarke INTERNATIONAL
Hemnall Street, Epping, Essex CM16 4LG
www.clarkeinternational.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>