LiftMaster PREMIUM Series Garage Door Opener User Guide
- June 9, 2024
- LiftMaster
Table of Contents
LiftMaster PREMIUM Series Garage Door Opener
Product Information
Lift Master PREMIUM Series Garage Door Opener
The Lift Master PREMIUM Series Garage Door Opener is designed for
residential use only. It should be installed and maintained according to the
instructions and warnings provided in the user’s guide to ensure safe
operation. The garage door opener is compatible with MyQTM and Security+ 2.0TM
accessories only. The Timer-to-Close feature should not be enabled if the
garage door opener is being installed on a one-piece door. The warning labels
enclosed with the product should be attached to the location indicated on the
label.
Product Usage
To ensure safe operation of the Lift Master PREMIUM Series Garage Door Opener, it is important to follow the installation, operation, and maintenance instructions provided in the user’s guide. Here are some important steps to keep in mind:
Installation
- Install the garage door opener ONLY on a properly balanced and lubricated garage door. An improperly balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH.
- All repairs to cables, spring assemblies, and other hardware MUST be made by a trained door systems technician BEFORE installing opener.
- Disable ALL locks and remove ALL ropes connected to the garage door BEFORE installing opener to avoid entanglement.
Product Operation
- Periodic checks of the garage door opener are required to ensure safe operation.
- The Timer-to-Close feature should only be used with sectional doors.
Please note that the images throughout the manual are for reference only, and your product may look different. For further information or assistance, please contact Lift Master customer support through the contact information provided in the user’s guide.
User’s Guide
FOR RESIDENTIAL USE ONLY
Write down the following information for future reference:
- Serial Number:
- Date of Purchase:
- Please read this guide and the enclosed safety materials carefully!
- The door WILL NOT CLOSE unless the Protector System® is connected and properly aligned.
- Periodic checks of the garage door opener are required to ensure safe operation.
- This garage door opener is ONLY compatible with MyQ™ and Security+ 2.0™ accessories.
- DO NOT enable the Timer-to-Close feature if you are installing the garage door opener on a one-piece door. The Timer-to-Close is to be used ONLY with sectional doors.
- Attach enclosed warning labels to the location indicated on label.
CONTACT INFORMATION
Leave this Users Guide with the homeowner.
The images throughout this manual are for reference and your product may look different.
- www.liftmaster.com
- The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196
Important Safety Instructions
safety Symbol and Signal Word Review
This garage door opener has been designed and tested to offer safe service
provided it is installed, operated, maintained and tested in strict accordance
with the instructions and warnings contained in this manual.When you see these
Safety Symbols and Signal Words on the following pages, they will alert you to
the possibility of serious injury or death if you do not comply with the
warnings that accompany them. The hazard may come from something mechanical or
from electric shock. Read the warnings carefully.
WARNING
- Mechanical
- Electrical
When you see this Signal Word on the following pages, it will alert you to the possibility of damage to your garage door and/or the garage door opener if you do not comply with the cautionary statements that accompany it. Read them carefully.
IMPORTANT INSTALLATION INSTRUCTIONS
WARNING
To reduce the risk of SEVERE INJURY or DEATH:
- READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.
- Install garage door opener ONLY on properly balanced and lubricated garage door. An improperly balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH.
- ALL repairs to cables, spring assemblies and other hardware MUST be made by a trained door systems technician BEFORE installing opener.
- Disable ALL locks and remove ALL ropes connected to garage door BEFORE installing opener to avoid entanglement.
- Install garage door opener 7 feet (2.13 m) or more above floor.
- Mount the emergency release within reach, but at least 6 feet (1.83 m) above the floor and avoiding contact with vehicles to avoid accidental release.
- NEVER connect garage door opener to power source until instructed to do so.
- NEVER wear watches, rings or loose clothing while installing or servicing opener. They could be caught in garage door or opener mechanisms.
- Install wall-mounted garage door control:
- within sight of the garage door.
- out of reach of children at a minimum height of 5 feet (1.5 m).
- away from ALL moving parts of the door.
- Place an entrapment warning label on wall next to garage door control.
- Place manual release/safety reverse test label in plain view on the inside of the garage door.
- Upon completion of installation, test the safety reversal system. The door MUST reverse on contact with a 1-1/2″ (3.8 cm) high object (or a 2×4 laid flat) on the floor.
- To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution, disconnect ALL electric and battery power BEFORE performing ANY service or maintenance.
- DO NOT enable the Timer-to-Close functionality if operating either one-piece or swinging garage doors. To be enabled ONLY when operating a sectional door.
- SAVE THESE INSTRUCTIONS.
NOTE: For complete installation instructions visit www.liftmaster.com to print the entire owner’s manual.
WARNING
To reduce the risk of SEVERE INJURY or DEATH
- READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.
- ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with garage door control push buttons or remote controls.
- ONLY activate garage door when it can be seen clearly, it is properly adjusted, and there are no obstructions to door travel.
- ALWAYS keep garage door in sight and away from people and objects until completely closed. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.
- NO ONE SHOULD GO UNDER A STOPPED, PARTIALLY OPENED DOOR.
- If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Use caution when using this release with the door open. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly and increasing the risk of SEVERE INJURY or DEATH.
- NEVER use emergency release handle unless garage doorway is clear of persons and obstructions.
- NEVER use handle to pull garage door open or closed. If rope knot becomes untied, you could fall.
- After ANY adjustments are made, the safety reversal system MUST be tested.
- Safety reversal system MUST be tested every month. Garage door MUST reverse on contact with 1-1/2″ high (3.8 cm) object (or a 2×4 laid flat) on the floor. Failure to adjust the garage door opener properly increases the risk of SEVERE INJURY or DEATH.
- ALWAYS KEEP GARAGE DOOR PROPERLY BALANCED. An improperly balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH.
- ALL repairs to cables, spring assemblies and other hardware, ALL of which are under EXTREME tension, MUST be made by a trained door systems technician.
- ALWAYS disconnect electric power to garage door opener BEFORE making ANY repairs or removing covers.
- This operator system is equipped with an unattended operation feature. The door could move unexpectedly. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.
- DO NOT enable the Timer-to-Close functionality if operating either one-piece or swinging garage doors. To be enabled ONLY when operating a sectional door.
- SAVE THESE INSTRUCTIONS.
Operation
Your garage door opener is equipped with features to provide you with greater control over your garage door operation. Accessories provided with your garage door opener will vary depending on the garage door opener model purchased.
ALERT2CLOSE
The Alert2Close feature provides a visual and an audible alert that an
unattended door is closing.
TIMER-TO-CLOSE (ITC)
The Timer-to-Close feature automatically closes the door after a specified
time period that can be adjusted using a TIC enabled door control (Models 881
LM or 880LM). Prior to and during the door closing the garage door opener
lights will flash and the garage door opener will beep.
MyQ™
MyQ™ technology uses a 900MHz signal to provide two-way communication between
the garage door opener and MyQ™ enabled accessories. Your garage door opener
is compatible with up to 16 MyQ™ accessories.
REMOTE CONTROLS AND DOOR CONTROLS (SECURITY+ 2.0™)
Your garage door opener has already been programmed at the factory to operate
with your remote control, which changes with each use, randomly accessing over
100 billion new codes. Compatible with MyQ™ and Security+ 2.0™.
NOTE: Older LiftMaster remote controls, door controls, and third party products are not compatible.
THE PROTECTOR SYSTEM® (SAFETY REVERSING SENSORS)
When properly connected and aligned, the safety reversing sensors will detect
an obstruction in the path of the infrared beam. If an obstruction breaks the
infrared beam while the door is closing, the door will stop and reverse to
full open position, and the opener lights will flash 1 0 times. If the door is
fully open, and the safety reversing sensors are not installed, or are
misaligned, the door will not close from a remote control. However, you can
close the door if you hold the button on the door control or keyless entry
until the door is fully closed. The safety reversing sensors do not affect the
opening cycle.
ENERGY CONSERVATION
For energy efficiency the garage door opener will enter sleep mode when the
door is fully closed. The sleep mode shuts the garage door opener down until
activated. The sleep mode is sequenced with the garage door opener light bulb;
as the light bulb turns off the sensor LEDs will turn off and whenever the
garage door opener lights turn on the sensor LEDs will light.
LIGHTS
The garage door opener light bulbs will turn on when the opener is initially
plugged in; power is restored after interruption, or when the garage door
opener is activated. The lights will turn off automatically after 4-1/2
minutes. An incandescent A19 light bulb (100 watt maximum) or for maximum
energy efficiency a 26W (1 00W equivalent) compact fluorescent light (CFL)
bulb may be used.
Light Feature
The garage door opener is equipped with an added feature; the lights will turn
on when someone enters through the open garage door and the safety reversing
sensor infrared beam is broken. For added control over the light bulbs on your
garage door opener, see page 6.
USING YOUR GARAGE DOOR OPENER
The garage door opener can be activated through a wall-mounted door control,
remote control, wireless keyless entry or MyQ™ accessory. When the door is
closed and the garage door opener is activated the door will open. If the door
senses an obstruction or is interrupted while opening the door will stop. When
the door is in any position other than closed and the garage door opener is
activated the door will close. If the garage door opener senses an obstruction
while closing, the door will reverse. If the obstruction interrupts the sensor
beam the garage door opener lights will blink 1 0 times. However, you can
close the door if you hold the button on the door control or keyless entry
until the door is fully closed. The safety reversing sensors do not affect the
opening cycle. The safety reversing sensor must be connected and aligned
correctly before the garage door opener will move in the down direction.
Using the Door Control
MOTION-DETECTING CONTROL PANEL
PUSH BAR
Press the push bar to open and close the door.
LIGHT BUTTON
Press the LIGHT button to turn the garage door opener lights on or off. When
the lights are turned on they will stay on until the LIGHT button is pressed
again, or until the garage door opener is activated. Once the garage door
opener is activated the lights will turn off after the specified period of
time (the factory setting is 4-1/2 minutes). The LIGHT button will not control
the lights when the door is in motion. The duration of the light timing can be
adjusted using the door control, see page 6.
The following features are accessible by lifting the push bar:
LEARN A DEVICE
Any compatible remote controls, wireless keyless entry, or MyQ™ accessories
can be programmed to the garage door opener by pressing the Learn button on
the
Motion-Detecting Control Panel.
LOCK
The LOCK feature is designed to prevent activation of the garage door opener
from remote controls while still allowing activation from the door control and
keyless entry. This feature is useful for added peace of mind when the home is
empty (i.e. vacation).
AUTOMATIC LIGHT
Motion Sensor
Factory default is set to on. This feature automatically turns on the garage
door opener lights when motion is sensed. The lights will come on for the set
period of time, then shut off. If using the garage door opener light as a work
light disable the motion sensor, otherwise the light will turn off
automatically if you are beyond the range of the sensor.
Light Feature
The lights will turn on when someone enters through the open garage door and
the safety reversing sensor infrared beam is broken.
MAINTENANCE ALERT SYSTEM (MAS)
This feature assists the homeowner in ensuring the garage door opener system
stays in good working condition. When the garage door opener needs to be
serviced (approximately 4500 garage door opener cycles) the command (yellow)
and service (red) LEDs will begin to alternately flash back and forth. The
factory setting for the MAS feature is off and can be activated at time of
installation. Contact your installing dealer for service.
Programming – Motion-Detecting Control Panel
Programming – Remote Controls
Your garage door opener has been programmed at the factory to operate with
your remote control. Older LittMaster remote controls are NOT compatible.
Programming can be done through the door control or the Learn button on the
garage door opener. To program additional remote controls refer to the
instructions provided with the additional remote controls or visit
www.littmaster.com. If your vehicle is equipped with a Homelink®, you may
require an external adapter depending on the make, model, and year of your
vehicle. Visit www.homelink.com for additional
information.
PROGRAM A REMOTE USING THE LEARN BUTTON ON THE GARAGE DOOR OPENER
When replacing the light lens cover, ensure the antenna wires are hanging straight down.
ERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES
- Press and hold the learn button on garage door opener until the learn LED goes out (approximately 6 seconds). All remote control and keyless entry codes are now erased. Reprogram any accessory you wish to use.
ERASE ALL DEVICES (Including MyQ™ enabled accessories)
- Press and hold the learn button on garage door opener until the learn LED goes out (approximately 6 seconds).
- Immediately press and hold the learn button again until the learn LED goes out. All codes are now erased. Reprogram any accessory you wish to use.
To Open the Door Manually
WARNING
To prevent possible SERIOUS INJURY or DEATH from a falling garage door:
- If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly.
- NEVER use emergency release handle unless garage doorway is clear of persons and obstructions.
- NEVER use handle to pull door open or closed. If rope knot becomes untied, you could fall.
DISCONNECT THE TROLLEY
- The door should be fully closed if possible.
- Pull down on the emergency release handle.
RECONNECT THE TROLLEY
The lockout feature prevents the trolley from reconnecting automatically.
- Pull the emergency release handle down and back (toward the opener). The door can then be raised and lowered manually as often as necessary.
- To disengage the lockout feature, pull the handle straight down. The trolley will reconnect on the next UP or DOWN operation, either manually or by using the door control or remote control.
Battery Backup (If applicable)
The battery backup system allows access in and out of your garage, even when
the power is out. When the garage door opener is operating on battery power,
the garage door opener will run slower, the light will not function, the
Battery Status LED will glow solid orange, and a beep will sound approximately
every 2 seconds.
The battery charges when the garage door opener is plugged into a 11 0Vac
electrical outlet that has power and requires 24 hours to fully charge. A
fully charged battery supplies 12Vdc to the garage door opener for one to two
days of normal operation during an electrical power outage. After the
electrical power has been restored, the battery will recharge within 24 hours.
The battery will last approximately 1 to 2 years with normal usage.
Instructions for replacement are provided with the battery. To obtain maximum
battery life and prevent damage, disconnect the battery when the garage door
opener is unplugged for an extended period of time.
NOTE: When the garage door opener is in battery backup mode the garage door opener lights, Timer-to-Close, and Remote Close features are unavailable.
BATTERY STATUS LED
NOTE: The Battery Status LED is most visible with the garage door opener light off. Battery does not have to be fully charged to operate the garage door opener.
GREEN LED:
All systems are normal.
- A solid green LED light indicates the battery is fully charged.
- A flashing green LED indicates the battery is being charged.
ORANGE LED:
The garage door opener has lost power and is in battery backup mode.
- A solid orange LED with beep, sounding approximately every 2 seconds, indicates the garage door opener is operating on battery power.
- A flashing orange LED with beep, sounding every 30 seconds, indicates the battery is low..
RED LED:
The garage door opener’s 12V battery needs to be replaced.
- A solid red LED with beep, sounding every 30 seconds, indicates the garage door opener needs servicing. Please call for replacement battery to allow your system to operate during a power outage.
Adjustment
Introduction
WARNING
Without a properly installed safety reversal system, persons (particularly
small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.
- Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system.
- After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2″ (3.8 cm) high object (or 2×4 laid flat) on floor.
CAUTION
- To prevent damage to vehicles, be sure fully open door provides adequate clearance. Your garage door opener is designed with electronic controls to make setup and adjustments easy. The adjustments allow you to program where the door will stop in the open (UP) and close (DOWN) position. The electronic controls sense the amount of force required to open and close the door.
NOTE: If anything interferes with the door’s upward travel it will stop.
It anything interferes with the door’s downward travel, it will reverse. To
watch a short instructional video on programming your new garage door opener
use your smartphone to read the OR Code below: 
PROGRAMMING BUTTONS
The programming buttons are located on the left side panel of the garage door
opener and are used to program the travel.
Program the Travel
WARNING
Without a properly installed safety reversal system, persons (particularly
small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.
- Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system.
- After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2″ (3.8 cm) high object (or 2×4 laid flat) on floor.
- If the garage door opener lights are flashing 5 times during the steps for Program the Travel, the programming has timed out. If the garage door opener lights are flashing 10 times during the steps for Program the Travel, the safety reversing sensors are misaligned or obstructed. When the sensors are aligned and unobstructed, cycle the door through a complete up and down cycle using the remote control or the UP and DOWN buttons. Programming is complete. If you are unable to operate the door up and down, repeat the steps for Programming the Travel.
Test the Safety Reversal System
WARNING
Without a properly installed safety reversal system, persons (particularly
small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.
- Safety reversal system MUST be tested every month.
- After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2″ high (3.8 cm) object (or 2×4 laid flat) on the floor.
If the door stops and does not reverse on the obstruction, increase the down travel (refer to Adjustment Step 1 ). Repeat the test. When the door reverses upon contact with the 1-1/2 inch board, remove the board and open/close the door 3 or 4 times to test the adjustment. If the test continues to fail, call a trained door systems technician.
Test the Protector System
WARNING
Without a properly installed safety reversing sensor, persons (particularly
small children) could be SERIOUSLY INJURED or KILLED by a closing garage door
.
The garage door opener will not close from a remote control if the LED in either safety reversing sensor is off (alerting you to the fact that the sensor is misaligned or obstructed). If the garage door opener closes the door when the safety reversing sensor is obstructed (and the sensors are no more than 6 inches [15 cm] above the floor), call for a trained door systems technician.
Maintenance
EVERY MONTH
- Manually operate door. If it is unbalanced or binding, call a trained door systems technician.
- Check to be sure door opens and closes fully. Adjust if necessary, see page 10.
- Test the safety reversal system. Adjust if necessary, see page 11.
EVERY YEAR
- Oil door rollers, bearings and hinges. The garage door opener does not require additional lubrication. Do not grease the door tracks.
- (If applicable) Test the battery backup and consider replacing the battery to ensure the garage door opener will operate during an electrical power outage.
Testing the Battery Backup:
-
Unplug the garage door opener. The battery status LED will either glow solid orange indicating opener is operating on battery power or will flash indicating low battery power.
-
Open and close the door using the remote control or door control.
NOTE: The garage door opener may run slower if the battery is not fully charged. The battery will take 24 hours to fully charge . -
Plug in the garage door opener. Verify the battery status LED is flashing green, indicating the battery is charging.
EVERY TWO TO THREE YEARS
- Use a rag to wipe away the existing grease from the garage door opener rail. Reapply a small layer of white lithium grease to the top and underside of the rail surface where the trolley slides.
The Remote Control Battery
WARNING
To prevent possible SER IOUS INJURY or DEATH:
- NEVER allow small children near batteries.
- If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
- Replace ONLY with 3V2032 coin batteries.
- DO NOT recharge, disassemble, heat above 212°F (100°C) or incinerate.
The lithium batteries should produce power for up to 5 years. If the battery is low, the remote control’s LED will not flash when the button is pressed. To replace battery, pry open the case first in the middle (1 ), then at each side (2 and 3) with the visor clip. Insert battery positive side up. Replace the batteries with only 3V2032 coin cell batteries. Dispose of old batteries properly.
NOTICE: To comply with FCC and/or Industry Canada (IC) rules, adjustment or modifications of this transceiver are prohibited. THERE ARE NO USER- SERVICEABLE PARTS. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC rules and IC RSS-21 0. Operation is subject to the following two conditions: (1 ) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian I CES-003.
Troubleshooting
Diagnostic Chart
Your garage door opener is programmed with self-diagnostic capabilities. The
UP and DOWN arrows on the garage door opener will flash the diagnostic codes
.
My garage door opener beeps:
The garage door opener can beep for several reasons:
- Garage door opener has been activated through a device or feature such as Timer-to-Close, garage door monitor or LiftMaster Internet Gateway, see page 4.
- Operating on battery power or the 12Vdc battery needs to be replaced (if applicable), see page 7 and 11.
My remote control will n ot activate the garage door:
- Verify the lock feature is not activated on the door control.
- Reprogram the remote control.
- If the remote control will still not activate the door check the diagnostic codes to ensure the garage door opener is working properly.
My door will not close and the light bulbs blinkon my motor unit:
The safety reversing sensor must be connected and aligned correctly before the
garage door opener will move in the down direction.
- Verify the safety sensors are properly installed, aligned and free of any obstructions.
My garage door opener l i g ht(s) will not turn off when the door is open:
The garage door opener is equipped with a feature that turns the light on when the safety reversing sensors have been obstructed or when the motion sensor on the door control detects movement in the garage. These features can be disabled using the door control, see page 6.
My neig hbor’s remote control opens my garage door:
Erase the memory from your garage door opener and reprogram the remote
control(s).
My vehicle’s Homeli nk® is not progra m m i n g to my garage door opener:
Depending on the make, model, and year of your vehicle an external adapter may
be required. Visit www.homelink.com for additional
information.
Repair Parts
NOTE: For additional parts not shown, visit www. liftmaster. com to
download or print the full owner’s manual.
Warranty
LIFTMASTER® ONE YEAR LIMITED WARRANTY LIFETIME MOTOR AND BELT LIMITED WARRANTY ONE YEAR LIMITED WARRANTY FOR THE BATTERY BACKUP SYSTEM
The Chamberlain Group, Inc. (“Seller”) warrants to the first retail purchaser
of this product, for the residence in which this product is originally
installed, that it is free from defects in materials and/or workmanship for a
period of one year from the date of purchase, except that the motor and belt
are warranted to be free from defects in materials and/or workmanship for the
lifetime of the product while you own your residence, and the Battery Backup
System is warranted to be free from defects in materials and/or workmanship
for a period of one year from the date of purchase. The proper operation of
this product is dependent on your compliance with the instructions regarding
installation, operation, and maintenance and testing. Failure to comply
strictly with those instructions will void this limited warranty in its
entirety. If, during the limited warranty period, this product appears to
contain a defect covered by this limited warranty, call
1-800-528-9131, toll free, before
dismantling this product. You will be advised of disassembly and shipping
instructions when you call. Then send the product or component, pre-paid and
insured, as directed to our service center for warranty repair. Please include
a brief description of the problem and a dated proof-of-purchase receipt with
any product returned for warranty repair. Products returned to Seller for
warranty
repair, which upon receipt by Seller are confirmed to be defective and covered
by this limited warranty, will be repaired or replaced (at Seller’s sole
option) at no cost to you and
returned pre- paid. Defective parts will be repaired or replaced with new or
factory-rebuilt parts at Seller’s sole option. [You are responsible for any
costs incurred in removing and/or reinstalling the product or any component.]
ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE APPLICABLE LIMITED WARRANTY PERIOD SET FORTH ABOVE FOR THE RELATED COMPONENT(S) , AND NO IMPLIED WARRANTIES WILL EXIST OR APPLY AFTER SUCH PERIOD.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
THIS LIMITED WARRANTY DOES NOT COVER NON-DEFECT DAMAGE, DAMAGE CAUSED BY IMPROPER INSTALLATION, OPERATION OR CARE (INCLUDING, BUT NOT LIMITED TO ABUSE , MISUSE, FAILURE TO PROVIDE REASONABLE AND NECESSARY MAINTENANCE, UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT) , LABOR CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT, REPLACEMENT O F CONSUMABLE ITEMS (E.G. , BATTERIES IN REMOTE CONTROL TRANSMITTERS AND LIGHT BULBS) , OR UNITS INSTALLED FOR NON RESIDENTIAL USE. THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH , OR RELATING TO, THE GARAGE DOOR OR GARAGE DOOR HARDWARE, INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS , DOOR ROLLERS, DOOR ALIGNMENT OR HINGES. THIS LIMITED WARRANTY ALSO DOES NOT COVER ANY PROBLEMS CAUSED BY INTERFERENCE. UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL , INCIDENTAL OR SPECIAL DAMAGES ARISING IN CONNECTION WITH USE , OR INABILITY TO USE , THIS PRODUCT. IN NO EVENT SHALL SELLER’S LIABILITY FOR BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY. NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT.
Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
- If applicable.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>