ETERNICO AET-MS150Sx Wireless 2.4 GHz Basic Mouse User Manual
- June 9, 2024
- ETERNICO
Table of Contents
ETERNICO AET-MS150Sx Wireless 2.4 GHz Basic Mouse
THANK YOU FOR CHOOSING US!
We value your trust. We hope that you will be happy with our product, and as excited about it as we are. We try to offer products of the highest quality that satisfy even the most demanding requirements. If you are satisfied, it would make us very happy if you chose us again the next time youmake a purchase. We are environmentally conscious, therefore we use special eco- friendly packaging. Please recycle!
Recycling and Environmental Protection
We try to avoid using plastic packaging and film and only use them when they
are absolutely necessary to protect the product. So how are we different?
Packaging you can eat. •• Well, almost. 🙂
- We use ink made from soybeans as opposed to classic petroleum-based ink.
- The majority of our packaging is made from 100% recyclable paper.
- We limit the use of adhesives. If absolutely necessary, we make sure to choose only water-soluble ones.
We think globally, which means that we actively search for eco-friendly solutions. We keep an eye on trending technology and place findings of the scientific community into practice. We don’tjusttry to meet quotas and mandates, we aim to exceed them.
TECHNICAL PARAMETERS
- Connection: USB receiver
- Power: 5 V direct current 10 mA
- Sensor sensitivity:
- 800 / 1 200 / 1 600 DPI Default setting: 1,600 DPI
- Sensortype: optical
- Interface type: USB(2,4G)
- OS: Windows XPNISfA/7/8/10/11, Linux,Android
- Wireless range: 10m
- Dimensions: 110x70ic42mm
- Weight: BOg±Sg
OVERVIEW
- Left:mousebutton
- Centre wheel
- Skle buttons forward/ backward Right mouse button
- ON/OFFswfkh(atthebottom)
- OPI button (sensor senahfvlty setting)
INSTRUCTIONS
Inserting and replacing the bettery
You must insert a battery to control the mouse. Proceed as follows:
- Tum the mouse upside down, gently push the battery cover, and slide it outward.
- Insert a new 1.5V AA alkaline battery. Observe correct polarity when inserting the battery; it is marked on the bottom of the battery compartment.
- Replace the cover and slide it toward the center of the mouse. The correct placement of the cover is signalled by a snap.
When you replace the battery proceed in the same way, except remove the old battery.
Installation
The USB receiver is located in the space next to the battery. Turn the mouse
upside down, gently push the battery cover, and slide it outward. Remove the
USB receiver from the inside of the mouse and insert it into the USB-A port of
your computer. Switch the main switch to position ON.
The mouse is installed automatically so you can control the mouse quickly and
comfortably. Once the cursor appears on the screen, the mouse is ready to use.
Cleaning
Keep the wireless mouse clean. Switch the main switch to position OFF. Use only a dry, clean doth for cleaning. Do not use harsh cleaners, solvents, gasoline or other similar substances. Never wash the wireless mouse with water and do not immerse it in water. If you will not be using the wireless mouse for an extended period of time, set the power switch to OFF and remove the battery.
SAFETY INFORMATION
- Read the safety and operatinginstructions. Failure to observe the safety and operating instructions can endanger people or damage the device. And it may void your warranty.
- This product is only suitable for household use.
- This product is not a toy. It may contain small components. Please keep away from children.
- Do not use or leave the product in a dusty or otherwise polluted environment.
- Do not leave the product in high or low ambient temperatures. Keep the product in a dry environment.
- Keep this product away from heat sources such as stoves or direct sunlight. No naked flame sources, such as lighted candles, should be placed on the product.
- Do not expose the product to dripping or splashing water or other liquids. Do not place containers filled with water, such as vases, on the product.
- Do not touch the product with wet hands.
- This product is not considered a light fixture. Malce sure that continuous operation does not exceed six hours.
- Never look into the light for a long time. There is a risk of serious eye damage.
- Do not disassemble the product. Attempting to modify the power bank may damage the product andresult in a seriousinjury.
- Do not immerse the product in water or other liquids or throw it into a fire.
- Do not leave the product unattended while it is in operation.
- Avoid turning the product on and off frequently and repeatedly.
- While the product is in operation, it may become hot. This is a normal occurrence. Therefore, malce sure that there are no heat-sensitive objects/ surfaces near the product.
- If you notice an unpleasant odor or smolce while using the product, unplug the product immediately and stop using it. Contact an authorized customer center.
- Avoid overloading the product. Avoid dropping the product.
- Do not place any objects on the product. There is a risk of irreversible damage to the product.
- This product does not contain parts repairable by the user . In the event of a malfunction or defect contact the nearest authorized service center. Check it regularly for damage.
- Use only a soft, clean, dry doth to clean the surface.
- Do not use any chemical cleaners, abrasives, gasoline, thinners or other similar substances. Before cleaning, make sure that the product is disconnected from the power supply.
- Store the product in a dry and well-ventilated place. Do not place any objects on the product when in storage.
DISPOSAL OF USED BATTERIES
Batteries contain materials harmful to the environment. Do not dispose of batteries in ‘QI a regular community waste. Dispose of used batteries properly at collection points.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>