ETERNICO AET-MSB350B Bluetooth Wireless Mouse User Manual

: June 9, 2024
: ETERNICO

Table of Contents

THANK YOU FOR CHOOSING US!
TECHNICAL PARAMETERS
OVERVIEW
INSTRUCTIONS
Operating mode selection
CLEANING
SAFETY INFORMATION
DISPOSAL OF USED BATTERIES
Documents / Resources

AET-MSB350B Bluetooth Wireless Mouse ETERNICO AET-MSB350B
Bluetooth Wireless Mouse User Manual

THANK YOU FOR CHOOSING US!

We value your trust. We hope that you will be happy with our product, and as excited about it as we are. We try to offer products of the highest quality that satisfy even the most demanding requirements. If you are satisfied, it would make us very happy if you chose us again the next time you make a purchase.
We are environmentally conscious, therefore we use special eco-friendly packaging. Please recycle!

Recycling and Environmental Protection
We try to avoid using plastic packaging and film and only use them when they are absolutely necessary to protect the product. So how are we different?

Packaging you can eat… Well, almost. 🙂
We use ink made from soybeans as opposed to classic petroleum-based ink.
The majority of our packaging is made from 100% recyclable paper.
We limit the use of adhesives. If absolutely necessary, we make sure to choose only water-soluble ones.
We think globally, which means that we actively search for eco-friendly solutions. We keep an eye on trending technology and place findings of the scientific community into practice.
We don‘t just try to meet quotas and mandates, we aim to exceed them.

TECHNICAL PARAMETERS

Connection	USB receiver / Bluetooth
Power	1.5 V dir. current 20 mA; lx AA alkaline battery
Sensor resolution	800 / 1 200 / 1 600 DPI (1 200 DPI is the default sensor

OVERVIEW

ETERNICO AET-MSB350B Bluetooth Wireless Mouse - fig 1

Left mouse button
Centre wheel
Side buttons forward / backward
Right mouse button
DPI button (sensor resolution setting)
Optical sensor
Battery compartment cover
Button for switching operating modes
ON/OFF switch

INSTRUCTIONS

Inserting and replacing the battery
You must insert a battery to control the mouse. Proceed as follows:

Turn the mouse upside down, gently push the battery cover, and slide it outward.
Insert a new AA alkaline battery. Observe correct polarity when inserting the battery; it is marked on the bottom of the battery compartment.
Replace the cover and slide it toward the center of the mouse. The correct placement of the cover is signalled by a snap.
When you replace the battery proceed in the same way, except remove the spent battery.

Turning mouse On/Off
Turn the power switch on the bottom of the mouse to the “ON” position to turn on the mouse.
The LED indicator flashes three times. The default operating mode is 2.4 G.
When you are not using the mouse, set the power switch at the bottom of the mouse to the “OFF” position. This will prevent the battery from discharging prematurely.
If you will not be using the mouse for an extended period of time, turn the power switch on the bottom of the mouse to the “OFF” position and remove the battery. This will protect the mouse from damage if the battery electrolyte leaks.

Operating mode selection

The wireless mouse allows you to set the operating modes to 2.4 G, Bluetooth 1 or Bluetooth 2.
To select an operating mode, press the operating mode selection button at the bottom of the mouse repeatedly in the following order: (operating mode 2.4 G)- 1 (Bluetooth 1) – 2 (Bluetooth 2). The default operating mode is 2.4 G.

2.4 G operating mode selection Installation
The USB receiver is located in the space next to the battery. Turn the mouse upside down, gently push the battery cover, and slide it outward. Remove the USB receiver from the inside of the mouse and insert it into the USB-A port of your computer. The mouse is installed automatically so you can control the mouse quickly and comfortably. If the mouse is disconnected from the USB receiver or the mouse is not automatically paired with the USB receiver, the operating mode must be set to 2.4 G manually. Proceed as follows:

Simultaneously press and hold the right, center, and left mouse buttons for about 3 seconds. The 2.4 G pairing process starts and the LED indicator starts flashing.
The pairing time is 20 seconds. Insert the USB receiver into the USB-A port of your computer during this time.
Automatic pairing will take place. The 2.4 G operating mode LED goes out after approx. 2 seconds and the mouse cursor appears on the display.

Bluetooth operating mode selection
If you will be using a wireless mouse in Bluetooth operating mode, you must remove the USB receiver.

Press the operating mode selection button repeatedly to select the 1 (Bluetooth 1) or 2 (Bluetooth 2) mode. The LED indicator of the selected mode lights up.
Press and hold the operating mode selection button for more than 3 seconds to enter the pairing process. The LED indicator of the selected mode will flash. The pairing time is 3 minutes.
On your computer, select Settings – Devices – Bluetooth and switch Bluetooth to the “On” position. This method is valid for Windows 8 and higher. Click “Add Device – Bluetooth” to start the device search.
Wait for the search process to complete, then select the wireless mouse from the list of searched devices.
Regardless of the Bluetooth 1/Bluetooth 2 operating mode selection, the device name will appear as ET MSB350 BT3.0 and ET MSB350 BT5.0, depending on the supported Bluetooth version of the device to which it connects. The pairing process starts.
If the pairing was successful, the LED indicator of the selected operating mode will go out after approx. 2 seconds and the mouse cursor will appear on the display.

CLEANING

Keep the wireless mouse clean. Turn the switch to the “OFF” position before cleaning.
Use only a dry, clean cloth for cleaning. Do not use harsh cleaners, solvents, gasoline or other similar substances. Never wash the wireless mouse with water and do not immerse it in water.
If you will not be using the wireless mouse for an extended period of time, set the power switch to “OFF” and remove the battery.

SAFETY INFORMATION

Read the safety and operatinginstructions. Failure to observe the safety and operating instructions can endanger people or damage the device. And it may void your warranty.
This product is only suitable for household use.
This product is not a toy. It may contain small components. Please keep away from children.
Do not use or leave the product in a dusty or otherwise polluted environment.
Do not leave the product in high or low ambient temperatures. Keep the product in a dry environment.
Keep this product away from heat sources such as stoves or direct sunlight. No naked flame sources, such as lighted candles, should be placed on the product.
Do not expose the product to dripping or splashing water or other liquids. Do not place containers filled with water, such as vases, on the product.
Do not touch the product with wet hands.
This product is not considered a light fixture. Make sure that continuous operation does not exceed six hours.
Never look into the light for a long time. There is a risk of serious eye damage.
Do not disassemble the product. Attempting to modify the power bank may damage the product and result in a serious injury.
Do not immerse the product in water or other liquids or throw it into a fire.
Do not leave the product unattended while it is in operation.
Avoid turning the product on and off frequently and repeatedly.
While the product is in operation, it may become hot. This is a normal occurrence. Therefore, make sure that there are no heat-sensitive objects / surfaces near the product.
If you notice an unpleasant odor or smoke while using the product, unplug the product immediately and stop using it. Contact an authorized customer center.
Avoid overloading the product. Avoid dropping the product.
Do not place any objects on the product. There is a risk of irreversible damage to the product.
This product does not contain parts repairable by the user . In the event of a malfunction or defect contact the nearest authorized service center. Check it regularly for damage.
Use only a soft, clean, dry cloth to clean the surface.
Do not use any chemical cleaners, abrasives, gasoline, thinners or other similar substances. Before cleaning, make sure that the product is disconnected from the power supply.
Store the product in a dry and well-ventilated place. Do not place any objects on the product when in storage.

DISPOSAL OF USED BATTERIES

Batteries contain materials harmful to the environment. Do not dispose of batteries in a regular community waste. Dispose of used batteries properly at collection points.

www.eternico.net
Co. Reg. No. 27082440
Alza.cz a.s., Jankovcova 1522/53, 170 00 Prague 7, Czech Republic
© 2021 Alza.cz a.s. All Rights Reserved.

Documents / Resources

| ETERNICO AET-MSB350B Bluetooth Wireless Mouse [pdf] User Manual
AET-MSB350B, Bluetooth Wireless Mouse, Wireless Mouse, Bluetooth Mouse, Mouse
---|---