D-Link DIS-100G-5W Industrial Unmanaged Switch with 5 10/100/1000Base-T Ports Installation Guide

June 9, 2024
D-Link

DIS-100G-5W Industrial Unmanaged Switch with 5 10/100/1000Base-T
Ports Installation GuideD Link DIS 100G 5W Industrial Unmanaged Switch
with 5 10 100 1000Base T Ports

D-Link
DIS-100G-5W
Industrial Unmanaged Switch with 5 10/100/1000Base-T Ports

Package Contents

Open the shipping carton of the switch and carefully unpack its contents. The carton should contain the following items:

  • DIS-100G-5W switch
  • DC power terminal block
  • Wall mounting kit
  • DIN-Rail mounting kit
  • Quick Installation Guide

Hardware Overview

Interfaces

Interface Description
Ports 1-5 1000Base-T ports

LED Indicators

LED Status Description
ALM On red Power failure alarm occurs.
Off No power failure alarm.
P1 On green P1 power line has power.
Off P1 power line is disconnected or does not have power supply.
P2 On green P2 power line has power.
Off P2 power line is disconnected or does not have power supply.
Link/Act (Ports 1-5) On green Ethernet link is up.
Blinking green Ethernet link is up and there is traffic detected.
Off Ethernet link is down.
Speed      (Ports 1-5) On yellow 1000 Mbps connection is detected.
Off No link or 10/100 Mbps connection is detected.

DIP-switches

Pin № State Description
Pin 1 ON To enable the power alarm.
OFF To disable the power alarm.
Pin 2 ON To enable broadcast storm rate limit.
OFF To disable broadcast storm rate limit.
Pin 3-6 ON Not used.
OFF Not used.

Hardware Installation

DIN-Rail Mounting
Mounting steps:

  1. Screw the DIN-Rail bracket on with the bracket and screws in the accessory kit.
  2. Hook the unit over the DIN-Rail.
  3. Push the bottom of the unit towards the DIN-Rail until it snaps into place.

D Link DIS 100G 5W Industrial Unmanaged Switch with 5 10 100 1000Base T
Ports - Mounting

Wall Mounting
Screw on the wall-mount plate on with the plate and M4 screws in the accessory kit.D Link DIS 100G 5W Industrial Unmanaged Switch with 5 10 100 1000Base T
Ports - switch

Grounding the Switch
Use the following instructions to ground the switch. Please complete these steps before powering on the switch.

  1. Remove the grounding screw from the switch and place the grounding cable lug ring on top of the grounding screw opening.
  2. Insert the grounding screw back into the grounding screw opening and use a screwdriver to tighten the grounding screw, securing the grounding cable to the switch.
  3. Attach the terminal lug ring at the other end of the grounding cable to an appropriate grounding source.
  4. Verify that the connection between the grounding connector on the switch and the grounding source is secure

Connecting to a Power Source
The switch can be powered by two power supplies (input range 12 to 58 V DC). Insert the positive and negative wires (AWG 14-26) into V+ and V- contact on the terminal  block and tighten the wire-clamp screws to prevent the wires from being loosened.

Alarm Relay Connecting
The alarm relay output contacts are in the middle of the DC terminal block connector shown as the figure below. By inserting the wires and set the DIP switch of the  respective Port Alarm to “ON”, the relay output alarm will detect any port failures, and form a short circuit. The alarm relay out is “Normal Open”. ****

Information in this document is subject to change without notice.
© 2018 D-Link Corporation.
All rights reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals