WATTS IOM-T-096 Leveling Shim Kit 096 User Manual
- June 9, 2024
- WATTS
Table of Contents
WATTS IOM-T-096 Leveling Shim Kit 096
Introduction
The Leveling Shim Kit 096 supports the installation of the Snow/Ice Sensor
090/094 to sit flush with a slab surface which prevents standing water on top
of the sensor surface.
The 096 is placed over the Snow / Ice Sensor Socket 091, this allows a height
adjustment of up to 1/2″ to eliminate recession between the sensor and slab
surfaces.
Features
- Includes 3 shims: 2×1⁄8″ and 1×1/4″
- 1⁄8″, 1/4″, 3⁄8″, and 1/2″ height adjustments
- Constructed with brass
- 4 stainless steel screw sets
WARNING
Please read carefully before proceeding with installation. Your failure to follow any attached instructions or operating parameters may lead to the product’s failure. Keep this Manual for future reference.
Mounting The Leveling Shim Kit
Mounting in the Socket 091:
- This step requires pulling either 65 feet or 208 feet of cable through the conduit.
- For new installations, before installing the 090/094, measure the recession using the black plastic cover installed to the height of finished slab surface.
- For existing installations, you must remove the 090/094 and fish the cable back through the conduit. Measure the recession from the height of the Snow/Ice Sensor 090 to finished slab surface. Determine which shims to be installed based upon the recession.
- Place the 1⁄8″ shim on top of the socket to raise the sensor by 1⁄8″.
- Place the 1/4″ shim on top of the socket to raise the sensor by 1/4″.
- Place 1×1⁄8″ and 1×1/4″ shims on top o the socket to raise the sensor by 3⁄8″.
- Place 2×1⁄8″ and 1×1/4″shims on top of the socket to raise the sensor by 1/2″.
- Fish back the sensor cable through the conduit.
- Fasten the sensor to the socket using the appropriate stainless steel screw set provided.
- Ensure there isn’t debris on the sensor surface.
Technical Data
Leveling Shim Kit 096
| Literature | IOM-T-096, ES-T-096 |
|---|---|
| Packaged weight | 0.4 kg |
| Dimensions | 315⁄32″ OD x 1/4″ H (88 mm OD x 6.4 mm H) |
315⁄32″ OD x 1⁄8″ H (88 mm OD x 3.1 mm H)
Shim Material| Brass
Ambient conditions| -30 to 170°F (-34 to 77°C)
Included
| 4 #6-32, 1/2″, stainless steel screws
4 #6-32, 5⁄8″, stainless steel screws
4 #6-32, 3/4″, stainless steel screws
4 #6-32, 7⁄8″, stainless steel screws
Limited Warranty
Limited Warranty and Product Return Procedure
Limited Warranty The liability of tekmar® under this warranty is limited. The
Purchaser, by taking receipt of any tekmar product (“Product”), acknowledges
the terms of the Limited Warranty in effect at the time of such Product sale
and acknowledges that it has read and understands same.
The tekmar Limited Warranty to the Purchaser on the Products sold hereunder is
a manufacturer’s pass-through warranty which the Purchaser is authorized to
pass through to its customers. Under the Limited Warranty, each tekmar Product
is warranted against defects in workmanship and materials if the Product is
installed and used in compliance with tekmar’s instructions, ordinary wear and
tear excepted. The pass-through warranty period is for a period of twenty-four
(24) months from the production date if the Product is not installed during
that period, or twelve (12) months from the documented date of installation if
installed within twenty-four (24) months from the production date.
The liability of tekmar under the Limited Warranty shall be limited to, at
tekmar’s sole discretion: the cost of parts and labor provided by tekmar to
repair defects in materials and / or workmanship of the defective product; or
to the exchange of the defective product for a warranty replacement product;
or to the granting of credit limited to the original cost of the defective
product, and such repair, exchange or credit shall be the sole remedy
available from tekmar, and, without limiting the foregoing in any way, tekmar
is not responsible, in contract, tort or strict product liability, for any
other losses, costs, expenses, inconveniences, or damages, whether direct,
indirect, special, secondary, incidental or consequential, arising from
ownership or use of the product, or from defects in workmanship or materials,
including any liability for fundamental breach of contract.
The pass-through Limited Warranty applies only to those defective Products
returned to tekmar during the warranty period. This Limited Warranty does not
cover the cost of the parts or labor to remove or transport the defective
Product, or to reinstall the repaired or replacement Product, all such costs
and expenses being subject to Purchaser’s agreement and warranty with its
customers.
Any representations or warranties about the Products made by Purchaser to its
customers which are different from or in excess of the tekmar Limited Warranty
are the Purchaser’s sole responsibility and obligation. Purchaser shall
indemnify and hold tekmar harmless from and against any and all claims,
liabilities and damages of any kind or nature which arise out of or are
related to any such representations or warranties by Purchaser to its
customers. The pass-through Limited Warranty does not apply if the returned
Product has been damaged by negligence by persons other than tekmar, accident,
fire, Act of God, abuse or misuse; or has been damaged by modifications,
alterations or attachments made subsequent to purchase which have not been
authorized by tekmar; or if the Product was not installed in compliance with
tekmar’s instructions and / or the local codes and ordinances; or if due to
defective installation of the Product; or if the Product was not used in
compliance with tekmar’s instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, WHICH
THE GOVERNING LAW ALLOWS PARTIES TO CONTRACTUALLY EXCLUDE, INCLUDING, WITHOUT
LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, DURABILITY OR DESCRIPTION OF THE PRODUCT, ITS NON-INFRINGEMENT OF ANY
RELEVANT PATENTS OR TRADEMARKS, AND ITS COMPLIANCE WITH OR NON-VIOLATION OF
ANY APPLICABLE ENVIRONMENTAL, HEALTH OR SAFETY LEGISLATION; THE TERM OF ANY
OTHER WARRANTY NOT HEREBY CONTRACTUALLY EXCLUDED IS LIMITED SUCH THAT IT SHALL
NOT EXTEND BEYOND TWENTY-FOUR (24) MONTHS FROM THE PRODUCTION DATE, TO THE
EXTENT THAT SUCH LIMITATION IS ALLOWED BY THE GOVERNING LAW.
Product Warranty Return Procedure All Products that are believed to have
defects in workmanship or materials must be returned, together with a written
description of the defect, to the tekmar Representative assigned to the
territory in which such Product is located. If tekmar receives an inquiry from
someone other than a tekmar Representative, including an inquiry from
Purchaser (if not a tekmar Representative) or Purchaser’s customers, regarding
a potential warranty claim, tekmar’s sole obligation shall be to provide the
address and other contact information regarding the appropriate
Representative.
All specifications are subject to change without notice
Tel: 1-800-438-3903
Fax : 250-984-0815
tekmarControls.com
© 2022 tekmar
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>