theben SUL 181 Schaltuhr Analogue Time Switch User Manual
- June 9, 2024
- theben
Table of Contents
- theben SUL 181 Schaltuhr Analogue Time Switch
- General information
- Technical data
- Designated Use
- Installation
- Connection
- Description
- Set time
- Set switching times
- Set manual operation / switching pre-selection
- Set 1 – – 0 permanent switching
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
theben SUL 181 Schaltuhr Analogue Time Switch
WARNING
Danger of death through electric shock or ire!
- Installation should only be carried out by professional electrician!
- Disconnect the mains power supply prior to installation and/or disassembly!
General information
- Analogue time switch
- Daily program
- 1 channel
- Shortest switching time 15 min
Technical data
- Operating voltage: 110 – 230 V AC
- Frequency: 50–60 Hz
- Power consumption: 1 VA
- Rated impulse voltage: 4 kV
- Contact: wo way switch
- Opening width: < 3 mm (μ)
- Switching capacity: 16 A, 250 V~, cos ϕ = 1 4 A, 250 V~, cos ϕ = 0,6 Min. switching
- capacity: 24 V / 100 mA AC
- Incandescent lamp load: 1100 W
- Operating temperature: –20 °C … +55 °C
- Protection class: II in accordance with EN 60669-1 subject to designated installation
- Protection rating: IP 20 in accordance with EN 60529
- Time accuracy: ±1s/day (20 °C)
- Power reserve: R 200 h (230 V), R 100 h (110 V)
- Pollution degree: 2
- Type: 1 BSTU
Designated Use
- The time switch can be used for lighting, ventilation, fountains, advertising hoardings etc.
- Only for use in closed, dry rooms
- Installation on DIN top hat rail (in accordance with DIN EN 60715)
- The switching of any external wire is permitted, switching of SELV is not permitted.
Installation
- Install on DIN top hair rails (in accordance with EN 60715)
- Disconnect power source
- Strip cable by 8 mm (max. 9 mm)
- Insert cable at 45° in the open terminal
- cables per terminal is possible
- Only with lexible wires: Press screwdriver downwards to open spring terminal
Disconnecting the cable
Use the screwdriver to push the load line connection opener downwards
Connection
- Note connection diagram
- Quarz movement only starts in a few minutes after power is switched on.
- Full power reserve is achieved after approx. 5 days.
Description
-
Switching pre-selection/switching status indicator
– 0 = off
– 1 = on -
Timing disc for time display (switching time)
-
Switching segments for programming SUL 181 d (1 = 15 min)
-
Morning/afternoon (AM/PM) time display (current time)
-
Hand for setting time (hours and minutes) can be adjusted clockwise; turn minute hand irmly to right
-
Three way switch:
Permanent ON – AUTO – Permanent OFF
Do not turn at the switching disc! Set the times only with the clock hand!
Set time
-
* e.g. 3:00 (morning)
- e.g. 15:00 (afternoon)
Set switching times
-
* e.g. 6:15–10:45; 16:15–21:00 ON
Set manual operation / switching pre-selection
• in advance 3:00 ON (= 1)
→ The time switch operates the set switching
times, i.e. it returns to program.
Set 1 – – 0 permanent switching
- Program is not operated.
- 1 = Permanent ON
- 0 = Permanent OFF
Hotline Theben:
J +49 7474 692-369
Theben AG | Hohenbergstraße 32 | 72401 Haigerloch | GERMANY | Telefon +49 7474 692-369 | info@theben.de | www.theben.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>