LILLIPUT 17.3 Inch 1RU Pull out Rack Mount Monitor User Manual

LILLIPUT 17.3 Inch 1RU Pull-out Rack Mount Monitor

Important Safety Instructions

• Please read User Guide before using this product.
• Please keep User Guide for future reference.
• Please read the precaution to prevent possible danger and loss of property.

Precaution

• Please do not place the display screen towards the ground.
• Please avoid heavy impact or drop onto the ground.
• Please do not use chemical solutions to clean this product. Please wipe with a clean soft cloth to maintain the brightness of the surface.
• Please do not block any vent holes.
• Please follow the instructions and trouble-shootings to adjust the product. Other improper adjustments may result in damage. Any further adjustment must be performed or conducted by a qualified technician.
• Please unplug the power and remove the battery if long-term no-use, or thunder weather.

Production Description

Front Panel

1. Earphone Jack
2. POWER: Power ON/OFF.
3. SDI: Signal switch to SDI mode when light on. (Only available on SDI HDMI version）
4. HDMI: Signal switch to HDMI mode when light on. (Only available on SDI HDMI version）
5. MENU
   • Press to enter menu.
   • Press to enter option in the menu. <
6. Select option in the menu.
   • Decrease the option value.
   • Before enter the menu, single press to activate function bar, press again to switch among of volume, brightness, contrast, color, hue, sharpness and backlight.  >
   • Select option in the menu.
   • Increase the option value.
7. Exit Button
8. F1~F3 User definable buttons
   • Assigned function by factory as follow:
   • [F1]: Peaking [F2]: Waveform [F3]: Level Meter （Long press any F1-F2-F3 buttons for 3-5 seconds to custom options.）

Rear Panel

Interfaces

1. 12V DC power port.
2. TALLY connecter.
3. SDI output port. (Only available on SDI HDMI Version)
4. SDI input port. (Only available on SDI HDMI Version)
5. HDMI output port.
6. HDMI input port.
7. USB port.
8. LAN port. (Connected to PC network interface for function adjustment.)

Menu Setting

Before setting the functions, please make sure the device is connected correctly.

Shortcut keys

Function Menu

• Under nonmenu screen, press < or > buttons to activate the function bar, and then press the “MENU” button can activate the shortcut menu bar to select brightness, contrast, saturation, tint, sharpness, volume, and backlight.
• Use the < or > button to adjust the value.
• The default function is [Back Light].

F1-F2-F3 Buttons:

• Long press any F1-F2-F3 buttons for 3-5 seconds to pop up the shortcut menu on the screen. As shown in Figure. Select the option via the < and > key, and set it as default via pressing the Menu button, then press the Exit button to exit the shortcut setting menu.
• Functions of F1-F2-F3 buttons can also be customized: [Center Marker], [Aspect Marker], [Safety Marker], [Overscan], [Scan], [Aspect], [Anamorphic], [Camera Log],[Check Field], [H/V Delay], [Freeze], [Image Flip], [Color Bar], [Peaking], [False Color], [Exposure], [Histogram], [Waveform], [Vector], [TimeCode], [Mute], [ Lever Meter].

(TimeCode is only available in SDI mode.)

• Default function: F1: [Scan]
• F2: [Waveform].
• F3: [Aspect]

MENU Operations

PICTURE

Brightness

• Control the degree of brightness between 0-100.

Contrast

• Control contrast ratio between 0-100.

Saturation

• Adjust the color intensity between 0-100.

Tint

• Adjust tint between 0-100.

Sharpness

• Control the sharpness of the image between 0-100.

Back Light

• Adjust the level of the backlight from 0 to 100.

RGB Range

• Use this item to choose the RGB range of the HDMI input: [Full], [Limited].
• Only available in HDMI mode.

HDMI DID

• Select the HDMI EDID from between [4K] and [2K].
• This item enables PC or other devices to recognize the property of this monitor and makes the images look excellent on the screen.
• Only available in HDMI mode.

Camera Log

• Use this item to choose one of the camera Log modes:
• [Off]: Turn off Camera Log.
• [Def. Log]: Use this item to choose one of the Camera Log modes as the following sequence:
• [SLog2ToLC-709], [SLog2ToLC-709TA], [SLog2ToSLog2-709], [SLog2ToCine+709], [SLog3ToLC-709],[SLog3ToLC-709TA], [SLog3ToSLog2-709], [SLog3ToCine+709],
• [ArriLogCTo709], [ArriLogCToP3DCI],[CLogTo709], [VLogToV709], [JLogTo709], [JLogTo709HLG], [JLogTo709PQ], [Z7 NLogTo709], [D780 NLogTo709]
• [User Log] : Use this item to choose one of the User Log modes (1-6). Please install the User Log as following steps:
• The User Log must be named with. Cube in the suffix. Please note: the device only supports the format of User Log: 17x17x17 / 33x33x33; Data order is BGR; Table order is BGR. If the format does not meet the requirement, please use tool “Lut Tool.exe” to transform it.
• Naming the User Log as User1-User6.cube, then copy the user Log into USB flash disk. Insert the USB flash disk to the device, the User Log is saved to the device automatically at the first time. If the User Log is not loaded for the first time, the device will pop up a prompt message, please choose whether to update or not.

HDR

• Use this item to choose one of the HDR presets: [Off], [ST 2084 300], [ST 2084 1000], [ST 2084 10000],[HLG].

Color Temp.

• Use this item to choose one of the color temperature presets: [5500K], [6500K], [7500K], [9300K],[User].
• Note: Only available under [User] mode to adjust R/G/B Gain and Offset.

R/G/B Gain

• Adjust the R/G/B Gain of the current Color Temperature from 0 to 255. Default value: 128.

R/G/B Offset

• Adjust the R/G/B Offset of the current Color Temperature from 0 to 511. Default value: 256.

MARKER

Center Marker

• Select [On] to display the center marker “+” and [Off] not to display it.

Aspect Marker

• Select the aspect ratio of the marker: [Off], [16:9], [1.85:1], [2.35:1], [2.39:1], [4:3], [3:2], [Grid], [User].
• Note : When [Aspect Marker] is selected as [Grid], the safety marker and Aspect Mat cannot be displayed.

User Marker

• H1/H2: Adjust the position of vertical markers from 1 to 1920 (The step value is 1). V1/V2: Adjust the position of horizontal markers from 1 to 1080 (The step value is 1).
• Note: User maker only in [Aspect Maker], [User] mode available.

Safety Marker

• Select [Off] not to display the safety marker. When this item is used with the Aspect Marker, it is only in Aspect Marker. When [Aspect Marker] is selected as [User], the safety marker does not be changed. Select the size of the safety markers: [95%], [93%], [90%], [88%], [85%], [80%].

Marker Color

• Select the color of the marker displayed on the screen: [Red], [Green], [Blue], [White], and [Black].

Aspect Mat.

• When activated, it can be selected from 1-7 (Step value is 1).

Thickness

• Adjust the thickness of all the marker lines from 1-7 (Step value is 1).

FUNCTION

Scan

• Adjust the scan mode among [Aspect], [Pixel To Pixel], and [Zoom].
• Note: Aspect, Anamorphic and Check Feld functions only can be adjusted only under [Aspect] mode.

Aspect

• Select the aspect of the image among [Full], [4:3].

Anamorphic

• Use this item to activate or deactivate anamorphic: Off、1.3X、1.5X、1.8X、2.0X、2.0X MAG.

Overscan

• Use this item to activate or deactivate overscan.

H/V Delay

• Select one of the H/V modes: [OFF], [H], [V], [H/V]. When H/V Delay on, the blanking portions of the input signal will be displayed horizontally and vertically.

Check Field

• Select one of check field modes: [Off], [Red], [Green], [Blue], [Mono].

Image Flip

• Select one of the Image Flip: [OFF], [H], [V], [H/V].

Zoom

• Select zoom scale from 10% to 90% (Step value is 10%).

Freeze

• Choose [On] to capture one frame of current image on the screen, and choose [Off] to close freeze function.

WAVEFORM

Full Mode

• Use this item to activate or deactivate Full Mode: [Off], [Y], [YCbCr], [RGB] and [Vector].

Waveform

• Use this item to activate or deactivate Waveform. Select the waveform mode from among [Off], [Y],[YCbCr], and [RGB].
• [Y]: Display Y Waveform.
• [YCbCr] : Display YCbCr Waveform.
• [RGB]: Display R/G/B Waveform.

Vector

• Use this item to activate or deactivate Vector.

Transparency

• Adjustment of transparency can support waveform, vector, histogram, level meter.
• Transparency can be selected from among [off], [25%], and [50%].
• [Off]: The background of waveform is shown at black.
• [25%]: The background of waveform is shown at 25% intensity.
• [50%] : The background of waveform is shown at 50% intensity.

Peaking

• Use this item to activate or deactivate the peaking function.

Peaking Color

• Select one of the peaking colors: [Red], [Green], [Blue], [White], and [Black].

Peaking Level

• Use this item to adjust the level of peaking from 1-100. The higher peaking level is, the more obvious peaking effect is.

False Color

• Use this item to activate or deactivate the false color function.
• When activated, [Default], [Spectrum], [ARRI], [RED] are for optional.

False Color Table

• Use this item to activate or deactivate the false color table.

Exposure

• Use this item to activate or deactivate the exposure function.

Exposure Level

• Use this item to adjust the level of exposure between 50-100 IRE.

Histogram

• Use this item to activate or deactivate histogram.

Time Code

• Use this item to activate or deactivate the Time Code. When activated, [LTC], [VITC] are for optional.
• Note: Time code is only available under SDI mode.

AUDIO

Volume

• Adjust the volume among 0-100.

Level Meter

• Select whether to activate or deactivate level meter.

Audio Ch.

• In HDMI mode, select the vector channels from among [Ch1&Ch2], [Ch3&Ch4], [Ch5&Ch6], and [Ch7&Ch8].
• In SDI mode, select the Vector Channels from among [Ch1&Ch2], [Ch3&Ch4], [Ch5&Ch6], [Ch7&Ch8], [Ch9&Ch10], [Ch11&Ch12], [Ch13&Ch14], and [Ch15&Ch16].

Mute

• Select whether to activate or deactivate Mute.

SYSTEM

Language

• Option: [Chinese], [English].

Color Bar

• Turn on/off the color bar. When the color bar is on, it can be selected: [100%], [75%].

OSD Timer

• Option: [10s], [the 20s], [30s].

Serve IP

• Manually configure the IP of the computer which the monitor needs to connect to xxx.xxx.xxx.xxx

DHCP

• [On]: The monitor will automatically get an IP address from a network for remote control via various programs.
• [Off]: Manually configure IP address.

IP Address

• Manually configure IP address: xxx.xxx.xxx.xxx
• Note: When [DHCP] on, IP address cannot be manually set.

Subnet Mask

• Manually configure Sub net Mask: xxx.xxx.xxx.xxx
• Note: When [DHCP] on, Sub net Mask cannot be manually set.

Gateway

• Manually configure Gateway: xxx.xxx.xxx.xxx
• Note: When [DHCP] on, Gateway cannot be manually set.

Reset

• Select the Reset option, press the Menu button to automatically reset.

Product Parameters

Accessories

Standard

1. 1 2 V DC adapter. 1 pc
2. Tally adaptor. 1 pc
3. User Manual. 1 pc

Trouble Shooting

1. Only black and white display:
   • Check whether the color saturation is properly setup or not.
2. Power on but no pictures:
   • Check whether the cables of SDI and HDMI are correctly connected or not.
   • Please use the standard power adapter coming with the product package. Improper power input may cause damage.
3. Wrong or abnormal colors:
   • Check whether the cables are correctly and p roperly connected or not. Broken or loose pins of the cables may cause a bad connection.
4. When on the picture shows size error:
   • Press “MENU → FUNCTION → Overscan” to zoom in/out pictures automatically when receiving HDMI signals.
5. Other problems:
   • Please press “MENU” button and choose “MENU→SYSTEM→ Reset →On”.
   • Note: Due to constant effort to improve products and product features, specifications may change without notice.

Appendix 1: 3D LUT Loading

• 3D LUT supports upload color calibration document and User Log via USB flash disk.

Format Requirement

• LUT format
• Type: .cube
• 3D Size: 17x17x17/33x33x33
• Data Order: BGR
• Table Order: BGR
• USB flash disk version
• USB: 2.0
• System: FAT32
• Size: <16G
• LUT format Color calibration document: Rec709. cube
• User Log: Us er1. cube User6.cube

LUT Format conversion

• Please convert LUT format according to the following steps.
• Note: For Mac users, please copy the “mac OS” file to Mac, then click and follow the steps below.
• Activate Lut converter
• One individual Product ID for one computer. Please send the ID number to Sales to get an Enter Key.
• Then the computer gets the permission of the Lut Tool after input the Enter Key.
• LightSpace CMS software user demo
• Activate LUT Tool.exe.
• Click Output File, and choose the file name.
• Click Generate Lut button to finish.

USB Loading

• Copy the needed files to the root directory of the USB flash disk. Plug the USB flash disk into USB port of the device after power on. Click “Yes” on the p op up prompt window (If the device doesn’t pop up the prompt window, please check the LUT document name or the USB flash disk version), then press Menu button to update automatically. It will pop up a prompt message if the update completed.

Appendix 2: Remote Terminal Instructions

Cross connection network cable

1. Connect LAN Port on the device to PC network interface by using network cable.
2. Manually configure the IP of the computer which the monitor needs to connect to: xxx.xxx.xxx.xxx
3. Install the Net framework The device uses OS Win 8 and above do not need to be installed as it ships with this framework.
   Note: The device uses OS below Win 8 need to be pre installed framework “dotNetFx40_Full_x86_x64.

Home Screen

1. Software Setup Open the software, it displays related IP address on the left of pop up window if the device is connected successfully.

2. Picture: The home screen of the application

3. Software Setup

4. Source Zone: To check and setup the selected Source. The settable parameters will be different for different Sources.

5. Select Zone: The software will read the data from the device which IP address marks as blue. Left click this IP address to select which device to be read. After selection, the user can change the Settings to setup the selected device. (Send to multiple devices is unavailable.)

6. Identify Button: Click to send the Identify to the selected device.
   The display screen will display the IP address. (Send to multiple devices is available.)

7. Copy & Paste Button: Use Copy Button with the Paste Button to read and save data get from the device whose IP address marks as blue. The copied data can be saved until the process is closed. After copying, the data from the display device, click Paste Button to save it. The data can be sent to select multiple devices.

8. Parameter Zone: The Parameter Zone includes Picture, Marker, Function, Waveform, Audio, and System. See the software interface for the details.

9. Current Signal Format: Displays the current signal format. It will refresh if the current signal changes.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>