LILLIPUT PVM210 21.5 Inch Professional Video Monitor User Manual

LILLIPUT PVM210 21.5 Inch Professional Video Monitor

Product Information

The monitor has a wide field of vision matched with excellent color space, reproducing the colorful world with the most authentic elements. It supports multiple video input interfaces such as SDI, HDMI, VGA, and AV. The monitor also features FN user-definable function buttons, markers, and aspect mat (pixel to pixel, zoom, aspect), scan (full scan, underscan, overscan), and marker color (red, green, blue, mono). Additionally, the monitor supports HDR10_300, HDR10_1000, HDR10_10000, and HLG. It has a color temperature of 6500K, 7500K, 9300K, and user-defined options. The monitor has HDMI1.4 supporting 4K 30Hz and 3G-SDI input & loop output. It has a high brightness of 1000cd/ and a high resolution of 1920X1080.

Product Usage Instructions

Safety Disposal For Old Electronic Equipment:
Please do not regard old electronic equipment as municipal waste and do not incinerate it. Instead, follow local regulations and hand it over to the applicable collection stand for safe recycling.
Front Panel: The front panel has a power button, an FN button that can be set by [Menu]-[System]-[FN Configuration], an EXIT button, a button to increase volume when powered on or select options downward in the menu, a button to decrease the volume when power on or select options upward in the menu, a MENU button to display the menu on the screen when powering on or confirm the option selected, an INPUT button to switch among AV, VGA, HDMI, and SDI signals, a brightness sensor, and a power light (red/green).
Rear Panel: The rear panel has a power input of DC 12V, an earphone input (3.5mm), an audio input, a video input, a VGA input, an HDMI 1.4 input, a USB 2.0 (for upgrade), an SDI output, an SDI input, and two speakers.
Supported Mounting Ways: The monitor can be mounted on the table by installing the desktop bracket on the bottom of the monitor or installed and fixed on the standard VESA bracket through VESA 75mm holes on its rear panel.

Important Safety Instructions

The device has been tested for conformance to safety regulations and requirements and has been certified for international use. However, like all electronic equipment, the device should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and minimize the risk of damage to the unit.

• Please do not place the display screen towards the ground to avoid scratching the LCD surface.
• Please avoid heavy impact.
• Please do not use chemical solutions to clean this product. Simply wipe with a soft cloth to keep clean of the surface.
• Please do not place on uneven surfaces.
• Please do not store the monitor with sharp, metallic objects.
• Please follow the instructions and trouble-shooting to adjust the product.
• Internal adjustments or repairs must be performed by a qualified technician.
• Please keep user guide for future reference.
• Please unplug the power and remove the battery if long-term no-use, or thunder weather.

Safety Disposal For Old Electronic Equipment
Please do not regard the old electronic equipment as municipal waste and do not incinerate old electronic equipment. Instead please always follow local regulations and hand it over to the applicable collection stand for safe recycling. Ensure that these waste materials can be effectively disposed of and recycled to prevent our environment and families from negative effects.

Introduction

This monitor is wide field of vision is matched with excellent color space, which reproduced the colorful world with the most authentic elements

Features

• HDMI1.4 supports 4K 30Hz.
• 3G-SDI input & loop output.
• 1000cd/㎡ high brightness.
• 1920X1080 high resolution.
• Support multiple video input interfaces: SDI, HDMI, VGA, AV.
• FN User-definable function button.
• HDR supporting HDR10_300, HDR10_1000, HDR10_10000, HLG.
• Color Temperature (6500K, 7500K, 9300K, User).
• Markers & Aspect Mat (Pixel to pixel, Zoom, Aspect ).
• Scan (Fullscan, Underscan, Overscan).
• Marker color (Red, Green, Blue, Mono).

Production Description

Front Panel

1. Power Button.
2. FN button, can be set by [Menu]-[System]-[FN Configuration]. Default: [Level Meter]
3. EXIT Button.
4. ▷ Button: Press it to increase volume when power on; Select options downward in the menu.
5. ◁ Button: Press it to decrease volume when power on; Select options upward in the menu.
6. MENU Button: Press it to display the menu on the screen when power on. Press it to confirm the option selected.
7. INPUT Button: Switch among of AV, VGA, HDMI and SDI signals.
8. Brightness Sensor
9. Power Light (Red/Green).

Rear Panel

1. Power input: DC 12V.
2. Earphone input(3.5mm).
3. Audio input.
4. Video input.
5. VGA input.
6. HDMI 1.4 input.
7. USB 2.0 (for upgrade).
8. SDI output.
9. SDI input.
10. Speaker*2.

Supported Mounting Ways

• Desktop
  Standing on the table by installing the desktop bracket on the bottom of the monitor.

• Wall mount
  Installed and fixed on the standard VESA bracket through VESA 75mm holes on its rear panel.

Menu Settings

Before setting the functions, please make sure the device is connected correctly.

Shortcut Button

Menu /▷/◁Button

• Press the MENU button, the menu will pop up on the screen. Then select the item as the following sequences by pressing the ▷/◁ button: PICTURE / MARKER / FUNCTION / VGA / AUDIO / SYSTEM. Press the MENU button again to enter the item you select.
• Press the ▷/◁ button to adjust options or values in the selected item. Then press the MENU or EXIT button to apply and save the setting.
• lWhen Menu is inactivated, press ▷/◁ button to adjust volume. Then select the item as the following sequences via pressing the MENU button: Brightness / Contrast / Saturation / Tint / Sharpness and Exit. Press the ▷/◁ button again to adjust the value in the selected item.

FN Button
Press the Menu button, and select [System]-[FN Configuration] to set the FN button function. Users can set the FN button function: Center Marker / Aspect Marker/ Check Field/ Display Scan/ Scan/ Aspect/ Freeze/ HDR/ Level Meter. Default: Level Meter.

Menu Operation
Before setting the functions, please make sure the device is connected correctly.
PICTURE

Marker

| Brightness| 0 – 100
---|---|---
Contrast| 0 – 100
Saturation| 0 – 100
Tint| 0 – 100
Sharpness| 0 – 100
HDR| Off, HDR10_300, HDR10_1000, HDR10_10000, HLG
Color Temp.| 6500K, 7500K, 9300K, USER

• Brightness
  Adjust the general brightness of the LCD from [0]-[100]. For example, if the user is outside in bright conditions, increase the LCD brightness to make it easier to view.

• Contrast
  Increases or decreases the range between the bright and dark areas of the image. High contrast can reveal detail and depth in the image, and low contrast can make the image appear soft and flat. It can be adjusted from [0]-[100].

• Saturation
  Adjust the color intensity from [0]-[100]. Turn the knob right to increase the color intensity and turn left to decrease it.

• Tint
  It can be adjusted from [0]-[100]. Affect the resulting color mixture’s relative lightness.

• Sharpness
  Increase or decrease the sharpness of the image. When the image sharpness is insufficient, increase the
  sharpness to make the image clearer. It can be adjusted from [0]-[100].

• HDR
  Options: [Off], [HDR10_300], [HDR10_1000], [HDR10_10000], [HLG].
  Note: Only available under SDI and HDMI mode.

• Color Temp
  [6500K], [7500K], [9300K], and [User] modes for optional.

Adjust the color temperature to make the image warmer (Yellow) or colder (Blue). Increase the value to make the image be warmer, and decrease the value to make the image be colder. Users can use this function to strengthen, weaken or balance the image color according to requirements. The standard white light color temperature is 6500K. Color Gain/Offset is available only under “User” mode to choose the color value.

MARKER

Marker

| Center Marker| ON, OFF
---|---|---
Aspect Marker| OFF, 1.85:1, 2.35:1, 4:3, 3:2
Safety Marker| OFF, 95%, 93%, 90%, 88%, 85%, 80%
Marker Color| Red, Green, Blue, White, Black
Grid| OFF, ON
Aspect Mat.| OFF, 1, 2, 3, 4, 5, 6, 7
Thickness| 2, 4, 6, 8

• Center Marker
  Select On, it will appear “+” marker on the center of the screen.

• Aspect Marker
  The Aspect Marker provides various aspect ratios, as the following: [OFF], [2.35:1], [1.85:1], [4:3], [3:2]

• Safety Marker
  Used to select and control the size and availability of the safety area. Available type are [OFF], [95%], [93%],
  [90%], [88%], [85%], [80%] preset to choose.

• Marker Color
  Select the color of the marker displayed on the screen: [Red], [Green], [Blue], [White], [Black].

• Grid
  Options: [ON], [OFF].

• Aspect Mat
  When activated, it can be selected from 1-7 (Step value is 1).

• Thickness
  Adjust the thickness of all the marker lines from[2], [4], [6], [8] (Step value is 2).

FUNCTION

Function

| Scan| Aspect, Pixel To Pixel, Zoom
---|---|---
Aspect| Full, 1.85:1, 2.35:1, 4:3, 3:2
Display Scan| Fullscan, Overscan, Underscan
Check Field| OFF, Mono, Red, Green, Blue
Zoom| X1.5, X2, X3, X4
Freeze| OFF, ON

• Scan
  Use this menu option to choose a Scan mode. There are three modes preset:

• Aspect
  Select Aspect under the Scan option, then use Aspect option to switch between several aspect ratio settings. For

• example:
  In 4:3 mode, images are scaled up or down to fill the maximum 4:3 portion of the screen. In Full mode, images are scaled to fill the entire screen.

• Pixel to Pixel
  The pixel-to-pixel is a monitor set to 1:1 pixel mapping with native fixed pixels, which avoids loss of sharpness due to scaling artifacts and normally avoids incorrect aspect ratio due to stretching.

• Zoom
  The image can be enlarged by [X1.5], [X2], [X3], and [X4] ratios. To select the [Zoom] under [Scan], choose the
  times under the [Zoom] option which is underneath the Check Field option.

  • Note! The zoom option can ONLY be activated when the user selects [Zoom] mode under the [Scan] function.

• Aspect
  Select the aspect of the image among [Full],[1.85:1], [2.35:1], [4:3], [3:2 ].

• Display Scan
  If the image shows a size error, use this setting to zoom in/out pictures automatically when receiving signals. The scan mode can be switched among [Fullscan], [Overscan], and [Underscan].

• Check Field
  Use the check field modes to monitor calibration or to analyze individual color components of an image. In [Mono] mode, all color is disabled and only a grayscale image is shown. In [Blue], [Green], and [Red] check field modes, only the selected color will be shown.
  Note! DSLR is available ONLY under HDMI mode.

• Freeze
  Activate the freeze function to freeze the current picture when playing the video.

• VGA

VGA

| Auto| ON, OFF
---|---|---
Phase| 0 – 100
Clock| 0 – 100
H-Position| 0 – 100
V-Position| 0 – 100

• Auto
  Select [On], the monitor can automatically adjust the position of the image. Select [Off], users can manually adjust the position of the image.

• Phase
  Adjust internal phase sequence difference. Adjustable range: 0-100.

• Clock
  Adjust internal oscillation frequency when interference occurs. Adjust this item, the image can be
  compressed or stretched left or right. Adjustable range: 0-100.

• H-Position
  Horizontally adjust the position of the image on the screen. Adjustable range: 0-100.

• V-Position
  Vertically adjust the position of the image on the screen. Adjustable range: 0-100.

AUDIO

• VGA, VIDEO mode
• SDI mode
• HDMI mode

AUDIO

| Volume| 0 – 100
---|---|---
Level Meter| OFF, ON
Audio Channel| CH0&1,  CH2&3,  CH4&5,  CH6&7,  CH8&9,  CH10&11,

CH12&13, CH14&15

• Volume
  Adjust the volume from [0]-[100] for the built-in speaker and earphone jack audio signal.

• Level Meter
  The left side of the on-screen meters displays level meters showing audio levels for channels 1 and 2 of the input source. It features peak hold indicators which stay visible for a short time so the user can clearly see the maximum levels reached. To achieve optimum audio quality, ensure the audio levels do not reach 0. This is the maximum level, meaning that any audio that exceeds this level will be clipped, resulting in distortion. Ideally peak audio levels should fall in the upper end of the green zone. If the peaks enter into the yellow or red zones, the audio is in danger of clipping.

• Audio Channel
  The monitor can receive 16 channels audio from SDI signal. The audio channel can be changed among [CH0&CH1], [CH2&CH3], [CH4&CH5], [CH6&CH7], [CH8&CH9], [CH10&CH11], [CH12&CH13], [CH14&CH15]

System

| Language| English,
---|---|---
OSD Timer| 10s, 20s, 30s
OSD Transparency| Off, low, Middle, High
Image Flip| Off, H, V, H&V
Auto Backlight| Off, ON
Back Light| 0 – 100
FN Configuration| Center Marker / Aspect Marker / Check Field / Display

Scan / Scan / Aspect / Freeze / Level Meter

Reset| OFF, ON

• Language
  Switch between [English] and [Chinese].

• OSD Timer
  Select the displaying time of the OSD. It has [10s], [20s], and [30s] presets to choose from.

• OSD Transparency
  Select the transparency of the OSD from [Off] → [Low] → [Middle] → [High]

• Image Flip
  The monitor support [H], [V], [H/V] three preset Flip modes.

• Auto Backlight
  Select On, the Auto Backlight function can be automatically adjusted according to the ambient brightness.

• Back Light
  Adjusts the level of the backlight level from [0]-[100]. If the backlight value is increased, the screen becomes brighter.

• F1 Configuration
  Select “F1 Configuration” for the setting. Functions: [Level Meter] → [Center Marker] → [Aspect Marker] → [Check Field] → [Display Scan] → [Scan] → [Aspect] → [Freeze]→ [HDR]. Default function: [Level Meter]

• Reset
  If there is any problem unknown, press to confirm after selecting. The monitor will return to default settings.

Parameter

Display

| Display Screen| 21.5″ LCD
---|---|---
Physical Resolution| 1920×1080
Aspect Ratio| 16:9
Brightness| 1000 cd/m²
Contrast| 1000: 1
Viewing Angle| 160°/ 160°(H/V)

Power

| Input Voltage| DC12-24V
Power Consumption| ≤36W
Source| Input| HDMI1.4 x1

Signal Format

|

3G-SDI LevelA/B

| 1080p(60/59.94/50/30/29.97/25/24/23.98/24sF/30sF/29.97sF/25sF/23.98sF)

1080i(60/59.94/50)

HD-SDI

| 1080p(30/29.97/25/24/23.98/30sf/29.97sf/25sf/24sf/23.98sf)

1080i(60/59.94/50)

720p(60/59.94/50/30/29.97/25/24/23.98)

SD-SDI

| 525i(59.94)

625i(50)

HDMI1.4

| 2160p(30/29.97/25/24/23.98)

1080p(60/50/30/29.97/25/24/23.98)

1080i(60/50)

Ear Jack| 3.5mm

Environment

| Operating

Temperature

| 0℃~50℃
Storage Temperature| -10℃~60℃

General

| Dimension (LWD)| 524.8×313.3×44.5mm
Weight| 5.1kg

Accessories

1. 15V DC Adapter 1 piece
2. HDMI A/A cable 1 piece
3. VGA cable 1 piece
4. VIDEO cable 1 piece
5. AUDIO cable 1 piece
6. Base bracket 1 pair

Trouble Shooting

1. Only black-and-white display:
   Check whether the color saturation and check field are properly set up or not.

2. Power on but no pictures:
   Check whether the cables of HDMI and 3G-SDI are correctly connected or not. Please use the standard power adapter coming with the product package. Improper power input may cause damage.

3. Wrong or abnormal colors:
   Check whether the cables are correctly and properly connected or not. Broken or loose pins in the cables may cause a bad connection.

4. When the picture shows a size error:
   Press [MENU] → [Function] →[Aspect] to zoom in/out pictures automatically when receiving HDMI signals

5. Other problems:
   Please press the Menu button and choose [MENU] → [System] → [Reset] → [ON].

6. According to the ISP, the machine can not function properly:
   ISP for program upgrades, non-professionals do not use. Please reboot your device if press accidentally!

7. Image Ghosting:
   If continue to display the same image or words on the screen for a long period of time, part of that image or words may burn into the screen and leave a ghosting image behind. Please understand it’s not a quality issue but the character of some screens, so no warranty/return/exchange for such a situation.

8. Some options can not be selected in the Menu:
   Some options are available only in a certain signal mode, such as HDMI, SDI, or VGA. Some options are available only when a certain feature is turned on. For example, the Zoom function shall be set after the following steps: [Menu] → [Function] → [Scan] → [Zoom] → [Exit] → [FN] → [Zoom].

Note: Due to constant efforts to improve products and product features, specifications may change without priority notice.

References

• All-guides – Innovative Search Service of Online Manuals

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>