LED WORLD LW-24100-5C-ADJ 24VDC 100W DMX512 Constant Voltage LED Driver User Manual
- June 9, 2024
- LED WORLD
Table of Contents
LED WORLD LW-24100-5C-ADJ 24VDC 100W DMX512 Constant Voltage LED Driver
User Manual
PRECAUTIONS BEFORE INSTALLING
- Read all instructions before installation. To be sold with instructions.
- Only qualified personnel should install the unit.
- Installation must comply with the National Electrical Code (Article 450) and Canadian Electrical Code
- Ensure the unit has the proper input/output voltage and output wattage for your application
- Check the wire markings to ensure they match the wiring diagram on this installation guide.
- Turn off power at breaker before starting.
INSTALLATION GUIDELINES
- The driver must be installed in a well-ventilated area free from explosives gases and vapors. Proper operation requires for free fiow of air. Do not install inside a cabinet smaller than 12 W x 12 H x 15 L inches. If you are installing multiple drivers, keep a minimum space of 5″ (127mm) between each driver. For Indoor or Outdoor use.
- Operate only within specified ambient temperature range of 4°F (-20°C) to 104°F (40°C). Operating at cooler surrounding air temperature will extend driver life.
- Do not overload. Total wattage of all LED fixtures used must not exceed the 100 watt rating of this power supply. Maximum of 80 watt for continuous use.
- All wiring must be in accordance with NEC/CEC, low voltage Class 2 circuit. For wire runs inside of walls, use properly certified CL2 or better cabling and appropriate mounting hardware. If you are unclear as to how to install and wire this product, contact a qualified licensed electrician. Failure to install this device properly may result in electrical shock or fire.
- Route and secure wires so they will not be pinched or damaged.
- Do not install Class 2 low voltage wiring in the same run(s) as AC main power.
MOUNTING
Select a suitable location capable of supporting the weight of the Driver. Use the four keyholes on the transformer case. Screw cover closed. Mount the unit at a height greater than 1ft (30cm) from the ground.
INPUT CONNECTIONS / GROUNDING
-
Remove the wiring cover (2 screws). Remove the wiring compartment
knockout and install strain reliefs (not included). With power turned off at the breaker, route the input wires. Connect one wire to black(L) and one wire to white(N) to the corresponding pigtail wire. -
For all wire connections use only UL/CSA listed wire nuts or wago connectors of suitable size and type.
-
The Driver case MUST be grounded in accordance with the NEC/CEC. Connect the ground wire to the driver green wire
-
Use 3/8” (1/2” KO) cable connectors (not included) to secure wire.
-
If used outdoor, must have knockouts point downwards. Use only outdoor rated
-
UL/CSA listed strain relief (water tight
-
Maximum of 12AWG through branch circuit conductor suitable for 105°C (221°F) permitted in box
OUTPUT CONNECTIONS (LOW VOLTAGE)
- Connect the wires of the light fixture to the driver wires – positive to the black(+) wire and negative to respective (-) wire.
- Measure the output voltage for proper voltage to LED fixture.
- After all wiring completion, screw in wiring cover
Use appropriate UL/CSA listed wire nuts or wago connectors (not included) to
connect wire
CONNECTION DIAGRAM
The following wiring diagram is as an example system connectivity. CAT5 (RJ45
connections) cables are the most effective solution for transmitting DMX-512
signals. XLR-3 cables may also be installed but require an additional adapter
for connecting to DMX Driver.
WARNING
- The LED Driver is not to be repaired. Do not use if it is damaged or defective.
- Installation involves special wiring methods to run wiring through a
- building structure. Consult a qualified licensed electrician.
TROUBLESHOOTING
Do not exceed 80 watts of continuous load! Note the wattage information on the item (strip label) that is being powered. If wattage or amperage information is not available or unknown, do not use. Power supply may be very warm if overloaded and will damage the unit (void limited warranty).
This device complies with FCC 47 CFR Part 15, Part B. Operation is subject to the following two conditions: (1)May not cause harmful interference, 2)Must accept any interference received, including interference that may cause undesired operation.
DOWNLOAD THE APP
Scan the QR code below to download NFC app. Scan the QR code for your phone’s operating system.
iOS
Android
ADDRESS WRITING
Select Write optio
Write screen with default options
Select first Type option as shown above and select DMX option from the men
Set the Address based on your zone. E.g. Set to 1 for Zone 1. 5 for Zone 2. 9 for Zone 3
Select Second Type option as shown above and select CV option from the menu
Set Level to 1. Confirm all the options and select WRITE button to complete
write operation
Ready to Scan notification will pop up when the app is ready to write address on the Driver.
Bring your phone very close to NFC tag, which is located on the other side
driver wiring compartment. Look for NFC sign shown below.
Success notification will pop up after successful DMX address wiring. If
notification displays Error message scan the NFC tag again.
Note: After every address write operation turn OFF the power and wait 5 seconds before turning ON. Also Turn OFF and ON DMX master controller.
ADDRESS READING
Select Read option
Follow the on screen notification. Scan NFC tag on the driver. After
successful scan app will display current DMX address settings of the driver
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.0 03/07/23
Copyright © 2023 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specifications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
References
- LED World Canada - A Commercial LED lighting supplier
- LED World Lighting - A Commercial LED lighting supplier
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>