Neomounts WL55-875WH1 Wall Mount Instruction Manual
- June 9, 2024
- Neomounts
Table of Contents
Neomounts WL55-875WH1 Wall Mount Instruction Manual
IMPORTANT HAZARD & SAFETY NOTES
Please read the safety and installation instructions in this product manual
carefully, before starting the installation
Failure to read, thoroughly understand and follow all instructions may result
in serious personal injury, damage to the equipment or voiding of factory
warranty.
General safety instruction
Use the appropriate tools and equipment when installing the motorised product.
Not using appropriate equipmentmay result in severe risk of injury
Electrical safety
Connect unit to a free accessible 220 – 240V, 50/60 Hz grounded power outlet
only. Make sure the unit can be immediately separated from the power outlet.
Only use unit in dry rooms, protect unit from water and other liquids. Only
wipe unit with dry cloth.
Do not open lift unit. RISK OF ELECTRIC SHOCK. There are no serviceable parts
inside.
In case of disfunction unplug unit from power outlet and call an authorised
technical service person.
Do not overrun or damage cables in any other way.
Replace damaged cables immediately with new one from same type.
Mechanical safety
Do not improperly load unit. Do not mount other than original parts in
conjunction with original mounting parts.
Do not hang on unit.
VERY HEAVY UNIT.
Severe risk of injury when unit falls over due to improper usage. Only use
original mounting parts provided with the
system. Do not exceed the maximum load of 110 kg. Assure installation of unit
by authorized service person only.
Before moving the unit up or down ashure at least a safety distance of 20 cm/8
inch from any part of the unit to any other fitment in order to avoid shear
traps or squeezing points.
In case of any incident, please release operating panel. Movement of unit will
stop immediately
The socket connections of the unit and the wall socket must be easily
accessible. Disconnect the power cable from
the wall socket before moving the product.
Moveable and free standing units
Only operate unit on flat and stable floor surfaces. Move unit on flat floors
only.
Risk of tilting when overrunning unevenness in floors, door sills and similar.
VERY HEAVY UNIT.
Severe risk of injury should the unit fall over. Lock brakes of all wheels
when operating unit. Always relocate the floor stand with screen in the lowest
position.
The device is not drip or splash water proof. Do not place liquids on or
nearby or spray the device. Always unplug
the unit from the wall socket before cleaning to reduce the risk of electric
shock.
Anti-collision protection
The protection system is designed to detect contact between the lift system
and an object. This system is intended for protection of the motorised screen
lift. The system is explicitly not intended as a safety mechanism to prevent
personal injury.
Wall mounting
Use appropriate mounting materials only. Choose douwels and screws according
to the wall type and material.
Using improper mounting material may result in tilting of the unit and severe
risk of injury.
Wall mounting must be done by experienced personnel only.
Instructions for disposal
Do not discard with general waste.
WL55-875WH1
STEP 1
Install the mount to a solid wall
STEP 2
Attach the back plate to the floor stand
STEP 3
Attach the control unit holder
STEP 4
Connect the plug of the control unit and place the remote control
STEP 5
Connect and route the cables
STEP 5
Install the hardware compartment
STEP 7
STEP 8
Install the adapter brackets and use spacers if necessary
STEP 9
Attach the screen onto the bracket and secure it
OPTION
Place the cable cover
STEP 10
Connect the floor stand to power
If the floorstand legs stops moving, a reset and rebalance will be needed.
- Push and hold the DOWN button on your remote until the legs are at the very bottom.
- Keep holding the DOWN button for another 5-10 seconds until the legs eact and move slightly upwards.
- When upwards reaction has been identified the remote control functionhas been restarted and the legs will react as normal to your remote actions
OPTION
Place the self-adhesive pads on the remote control holder and attach the holder where desired
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>