ROPOX TF-200.01.0054 Upper Cabinets User Guide
- June 9, 2024
- ROPOX
Table of Contents
ROPOX TF-200.01.0054 Upper Cabinets
Introduction
The Ropox Connect App is an application which allows you to remotely control your Ropox products. By connecting your iOS device to a Bluetooth adapter inserted into a Ropox product, you gain the ability to adjust your product upwards or downwards.
After pairing of an iOS device and a Ropox product has been completed, you’re able to remotely control the product from great distance. In practice, this oftentimes is greater than 10 meters. Additionally, the application allows you to save height settings, to enable you to easily change between pre-set heights.
How to download the App
For iOS
1. Scan the QR code or open the app: App Store.
2. In the App Store, press ‘Search’.
3. Search for ”Ropox Connect”.
4. Find the Ropox Connect App, and press ‘Get’.
Compatible products and functions
Setup
To connect to a Ropox product is quick and easy. Before your Ropox product can be remotely controlled, the Bluetooth adapter must be inserted into the product. To insert the Bluetooth adapter into your Ropox product, follow the instructions below.
When finding the correct Bluetooth device in the app, look for a device named LogicLink. Note, the Bluetooth adapter has two buttons on the front, allowing you to adjust the product in height, other than with the button that came with your Ropox product.
- Determine the placement of the adapter, then grab the Bluetooth adapter and the split-cable
-
- Insert the split-cable in the plug ”HS” in the control box. Then, insert the adapter in one end of the split-cable, and the button that came with the product, in the other
- If the adapter is to be fixed, it should be done now*. Use the drilling-template for this, as seen on the next page
- Put the adapter into ”Pairing-mode”. This is done by pressing twice on the small button in the back
Note! It is recommended, when multiple products need to be connected, that 1 adapter is inserted at a time, and then saved
Drilling-template
For screw-mounting the Bluetooth adapter on a hardened surface, it’s
recommended to use the adapter as a drilling template. Mark out the three
points, pre-drill, then mount the adapter. Screws are not included. For
mounting, cable ties or double-adhesive tape can also be used. Measurements of
the adapter can be seen below.
*Write down the pairing code from the back of the adapter before mounting!
Instructions for use
Saving a product
- Open the app Ropox Connect.
- From the main menu, press the red button.
- The app will locate all nearby Bluetooth devices in range. Choose the product you wish to save.
- Name your product and press save. The product has now been saved.
Note! When first connecting to the product, the adapter will request a pairing code. This is listed on the back of the adapter. Usually, this code is: 000000
Drive a saved product
- From the main menu, press on a saved product.
- The first time a product is connected to, you’re asked to measure and set a bottom height of the product. This is optional.
- Whether or not the bottom height has been set, the product can be driven with the ▲/▼ button, either upwards or downwards.
Note! When using the Ropox Connect app with certain products, including Vision and VertiInside, the height-display and saved settings-display will be disabled. Tilt on Vision is also disabled.
Saving a height setting
- From the main menu, press on a saved product.
- Drive the product to the desired height.
- Press save setting. Name the height setting and press save once again.
Drive with a saved height setting
- From the tab ’Saved settings’, press a saved setting.
- A press button is shown. Hold down the button until you’ve reached your saved setting.
- When the product has reached its saved setting, it’ll stop driving.
Settings
Remove a product or setting
- Press and hold and drag the product or setting to the left.
- Press the red icon and hit ‘Delete’. This will remove the product or saved setting.
Accessibility settings
Adjust the text size
- To adjust the text size, go to your device’s settings.
- From settings, scroll down and go to ‘Display & Brightness’.
- Scroll down and go to ’Text Size’.
- Adjust, with the slider, your device’s text size.
Haptic feedback
The Ropox Connect App will, as standard, provide haptic feedback in the form
of vibration, when it drives a Ropox product. This can be disabled or enabled
from the device’s settings.
Screen reader
Ropox Connect App is compatible with the screen reader, which can be enabled
from the device’s settings.
- Go to your device’s settings and scroll down to ‘Accessibility’.
- From ’Accessibility’, press ’VoiceOver’.
- From ’VoiceOver’, press the topmost slider to enable the screen reader.
Note! Adjusting your device’s accessibility settings will change the settings on the entire device, not just the app!
Troubleshooting
Can’t find the product in the App
- After pressing the red button from the main menu, look for LogicLink.
- If there is no LogicLink on the list, the Bluetooth adapter must reinitiate pairing-mode. This is done by pressing the small button on the back of the adapter twice.
- The product needs a reset. Read the user manual that came with the Ropox product, to learn of this procedure. Use the button that came with the product. Usually, a reset procedure is driving the product to its highest or lowest height, and then hold down the button in that direction for a few seconds.
Can’t connect to the product
Double click the button on the back, to put the adapter into pairing mode,
then attempt to reconnect.
Languages
The Ropox Connect app supports English and Danish, as described in this
manual, but can also support several other languages. A list of supported
languages is:
- English (GB/US)
- Danish (Danmark)
- Norwegian (Norge)
- Finnish (Suomi)
- German (Deutschland)
- Dutch (Nederland)
- Spanish (España)
- Italian (Italia)
- French (France)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>