ALLSPARES Beko 874960100 Refrigerator Water Filter Instruction Manual

ALLSPARES Beko 874960100 Refrigerator Water Filter Instruction Manual

Installation instructions

Before installation:

• Shut off the cold-water supply to the refrigerator before installation. Turn on the refrigerator water dispenser to release water pressure, letting water drain from the pipe completely.
• It is normal for black carbon fines (particles) to appear on the outside of your filter. This happens when the filter is jarred in shipping. It is safe to simply wipe it off.
• The filter connectors are larger to prevent leaks. You might have to twist the filter hard to make sure the connection is secure.

1. Push button on the filter housing to open it.

2. Gently pull out the old filter from the housing.

3. Remove the package and end-cap of the new filter.

4. Insert the new filter into the housing until it stops and push up on the filter to lock in place.
   Note: If the new filter is hard to rotate, please insert the filter a little bit towards the filter housing.

5. Close the filter housing lid until it locks into place.

6. Dispense water for a few minutes to remove carbon fines and trapped air from the system.
   Note: Initial water flow may be slower than expected. Full water flow will be restored within 24-36 hours.

7. Check filter one more time for any leaks.
   

Storage and maintenance

• Replace your filter every 6 months or 200 gallons to prevent bacteria and fungus growth in your filter, supply lines, and storage tank.
• Keep your unused filters in a cool, dark, and dry place until you need them.
• If you do not use your water dispenser for more than four days, run two gallons of water before using it to prevent bad tasting water.

Frequently asked questions

Q: Why is it difficult to twist the new filter into the filter housing?

A: The connector may expand because of water pressure. Therefore, it is recommended you push the new filter in with a little bit of force, but not too hard. Then turn it clockwise.

Q: Do I need to flush the filter after installation?

A: After installation, it is highly recommended you run water for a few minutes before using. Water filters are made from advanced coconut carbon block, so there are some carbon fines in the filter. Flushing removes the carbon fines to produce clean water.

Q: Must the filter be changed every 6 months?

A: Yes, you must replace the filter every six months or sooner if water flow is reduced or if there is heavy sediment / must present. Over-used filters will degrade the filtration performance.

Warning
To reduce the risk of property damage due to water leakage, this filter MUST be installed in accordance with the manufacturer’s specifications and instructions. This filter unit must be replaced every 750L or 6 months. Failure to follow instructions and operating specifications will void your warranty. Further, manufacturer assumes no responsibility or liability for damages arising out of misuse of the product.
Panasonic® is a registered trademark of Panasonic Corporation.
Panasonic® is used for reference purposes only

***** The service life mentioned above is subject to chlorine reduction. Actual result varies according to the local water quality.

Operating specifications

• Operating Temperature: 33 -100°F/0.6 – 38°C
• Working Pressure: 20 -100 psi/140 – 689 kPa
• Rated Capacity: 200 gallons/757 litres
• Flow Rate: 0.5 gpm/1.9 Ipm

Substance reduction

The system has been tested and certified by the NSF International according to NSF/ANSI Standard 42 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for the water leaving the system, as specified by NSF/ANSI Standard 42. While testing was performed under standard laboratory conditions, actual performance may vary.

Substance| Inf. Average| NSF Specified
Challenge
Concentration| Ave. %
Reduction(%)| Average
Product Water
Concentration| Max Permissible
Product Water
Concentration| NSF Reduction
Requirements| NSF Test
Report
---|---|---|---|---|---|---|---
Chlorine Taste
and Odor| 2.1 mg/L| 2.0mg/L± 1 013/0| 97.0%| 0.063mg/L| WA| 5096| J-00295502

**** Do not use with water that is micro-biologically unsafe or of unknown water quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used with disinfected water that may contain filterable cysts.

A replacement for the following water filters: BEKOs filters
BEKO° 4874960100
Filter life: up to 6 months or 750L, whichever comes first will vary based on water condition.

REPLACEMENT ELEMENT

Tested and Certified by NSF International against NSF/ANSI Standard 42 in model AS-FF220 for the reduction of the claims specified on the Performance Data Sheet, and to NSF/ANSI 372 (50.25% lead).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>