WiZ 348603472 Motion Sensor User Guide
- June 4, 2024
- wiz
Table of Contents
QUICK SETUP
348603472 Motion Sensor
Before starting the setup process. make sure at least 1 W1Z light in the room is turned on and connected to w,-Fi.
-
SELECT A ROOM IN THE APP
Press + on the top right corner and select “Motion Sensor”. -
ADD MOTION SENSOR TO ROOM
Follow the on-screen steps in the app to complete setup. -
ENJOY LIGHTING WITH MOTION DETECTION
Simply walk by to trigger your lights
Notes:
- By setting Rhythms for the room,n the WiZ app, you can make your sensor trigger different light modes at different times of the day.
- The w,z motion sensor,s attached to a single room and only triggers the lights in that room. You can move the sensor in the app if you want it to trigger lights in another room instead
Need help?
Get in touch through our in-app chat support.
What does it do?
WiZ motion sensor triggers automatic responses to turn on and turn off the
lights according to motion detection. You can also select the mode and
brightness of your choice for “motion” and “no motion” states. For example,
you could say “go to Daylight when there is motion, and night light when
there,s none”. Motion detection works without Wi-Fi. The detection range is
approximately 3 meters (10 feet) with a beam angle of 120 degrees.
The motion sensor control range (i.e the distance between the motion sensor
and controlled lights) is approximately 15 m (SO feet) in a normal room
environment with partitions and walls. The range can be longer with a clear
line of sight. The exact distance depends on the surrounding environment as
obstacles may weaken the signal. 
Adjust the sensitivity of the sensor and the battery usage time
RT: Response Time (the default setting) It increases the responsiveness
of the sensor, which will report the absence of motion after S minutes.
LT: LI, Time (of battery). It makes the sensor report the absence of
motion after 12 minutes. thus increasing the battery lifetime.
| Product | WiZ PIR motion sensor |
|---|---|
| Reference | 9.29E+09 |
| Location | For indoor use |
| Ambient temperature | -2o·c – +45 C / -4 . F – +113 . F |
| Battery type | LR6 (AA) 1.5 Vd.c x 2 (not provided) |
Important information
- For indoor use only. Do not try to open or repair it (except for battery replacement).
- Suitable for dry location only.
- Use only with specified batteries; do not use rechargeable batteries; do not use different brands or new/old batteries together; replace the exhausted batteries in time.
- Keep,t away from water and heat sources (e.g heater, air cond1t1oner airflow).
Symbols explanation:
Waste Electrical and Electronic Equipment
This product must be disposed of at a designated collection point for
Electrical and Electronic waste. For more information, contact your local city
office or the shop where you purchased the product.
**** Indoor use only
Caution:
The device complies with Part 15 of the FCC Rules / Industry Canada license-
exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
MPE Reminding
To satisfy FCC/ IC RF exposure requirements, a separation distance of 20 cm or
more should be maintained between the antenna of this device and persons
during device operation.
To ensure compliance, operations closer than that distance are not
recommended.
Wi-Fi, the Wi-Fi logo, and the Wi-Fi CERTIFIED logo are registered trademarks
of Wi-Fi Alliance.
Wt-Fi CERTIFIED'”, WPA2′” are trademarks of Wi-Fi Alliance.
Google, Google Play, and the Google Play logo are trademarks of Google L LC.
The Apple logo and Siri are trademarks of Apple Inc., registered in the U.S.
and other countries and regions. App Store is a service mark of Apple Inc.
All product names, logos, and brands are the property of their respective
owners.
Any use of such marks by Signify is under license.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>