SCANSTRUT ROKK SC-USB-02 Charge+ Waterproof USB Socket Instruction Manual
- June 9, 2024
- SCANSTRUT
Table of Contents
ROKK SC-USB-02 Charge+ Waterproof USB Socket
Instruction Manual
Part List
Tools Required
-
Mark hole centre for drilling
-
Drill mounting holes (see tools required).
Pilot Hole Size
Material| No. 6 Screw
---|---
Soft Material e.g Plywood| 2.5mm (3/32″)
Hard Material e.g Fiberglas| 3mm (1/8″) -
– Feed SC-USB-03 through the gasket and hole.
– Tighten lock ring onto product until securely fixed.
– Screw product into place.
-
Connect to 12/24V supply, ensuring a waterproof connection. Fuse and select cable diameter according to input voltage and current for your specific installation.
Technical information
| Input voltage 12/24V System | 10-32V DC |
|---|---|
| Input current Max | 2.5 A |
| Output Type A | 5V⎓2.1A |
| Output Type A | 5V⎓2.1A |
| Total Output Current | 4.2 A |
| Standby draw | 0.01 W |
| Waterproof rating | IPX6 |
| Certification | CE, ROHS, UKCA |
READ IMPORTANT SAFETY INFORMATION
BEFORE INSTALLING.
WARNING:
This product is to be connected to a 12V DC or 24V DC battery power source
only.
The power supply must be switched off before installation.
An appropriate fuse or circuit breaker must be used between the battery/power
source and this product. Check for correct polarity of all wiring before
switching the power on.
This product may contain high voltages.
Do not tamper with the product.
This product is NOT approved for use in hazardous/flammable atmospheres.
Do NOT install in a hazardous/flammable atmosphere e.g. engine room.
Before drilling any holes, ensure the area behind the mounting location is
clear of wires, fuel and all other hazardous objects.
Ensure any holes cut will not significantly weaken the structure of the
mounting surface.
If the product needs to be mounted outside, it must be mounted in a location
safely above the waterline, where it is not at risk of being submerged.
CAUTION:
This product does not contain any user serviceable parts. DO NOT attempt to
repair or modify the product in any way.
When used in high ambient temperature or in direct sunlight, the product may
turn off temporarily, this is a safety feature of the electronics.
The IP protection rating is only valid if the installation is carried out
correctly according to the instructions and on a perfectly flat, smooth and
non-porous surface.
When choosing a mounting location, avoid areas exposed to heat radiation
devices and areas with poor ventilation
WIRING:
Professional electrician installation recommended, see Technical Information
for power requirements.
To achieve max power output, the specified voltage must be at the charger.
Battery performance and voltage drop needs to be considered for installation.
ENVIRONMENTAL PROTECTION:
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or
retailer for recycling advice.
IMPORTANT:
Scan strut Ltd & Inc. accepts no responsibility for any injuries or other
damages arising from the use of their products in any circumstances.
WARRANTY
A 2 year, non-transferrable warranty covers this Scan strut product only and
not any devices that are charged by it. No warranty is given for users’
devices and users expose their devices to hazards, known or unknown, at their
own risk.
CE Warning
Scans tut Ltd, declares the product ‘ROKK CHARGE+’ SKU: SC-USB-02 is in
compliance with EMC CE Directive (2014/30/EC).
The CE certificate of conformity can be found at
www.scanstrut.com/uk/compliance.
Cutting Template
1:1 Scale
Print document 1:1
Scale for correct cutting template size.
UK & International
+44 (0)1392531280
sales@scanstrut.com
For further installation and warranty information
Please visit: www.scanstrut.com
USA
+1 860 308 1416
usasales@scanstrut.com
23-01-2023 (Issue 2)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>