Hosonsoft HS/D-YF-A0-005 Professional Digital Printing Software Instructions
- June 9, 2024
- Hosonsoft
Table of Contents
HS/D-YF-A0-005 Professional Digital Printing Software
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Printing Software Instruction
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Revision Record
Date
Version
March 15, 2018 First version
Revised sections
April 17, 2018
Revision description
Author
Liu Guangtao, Chenyan
Add button description, operation steps of new version of card, network access method, judgment method of gigabit NIC, firmware import/export and so on.
Liu Guangtao
Table of Contents I.Printing software overview
……………………………………………………………………………………………………………………………………..5 II. Software start and
online ………………………………………………………………………………………………………………………………………5
1.Start print control software
………………………………………………………………………………………………………………………………5 2.Software online
settings…………………………………………………………………………………………………………………………………..5
2.1 Gigabit NIC judgment …………………………………………………………………………………………………………………………..5 2.2
Network settings …………………………………………………………………………………………………………………………………..6
III.Operation steps before the new board card is used
…………………………………………………………………………………………………..9 1Set the IP
address…………………………………………………………………………………………………………………………………………..10 2 Motor gear
ratio calibration……………………………………………………………………………………………………………………………10 3 Clean
print head……………………………………………………………………………………………………………………………………………10 4
Calibration …………………………………………………………………………………………………………………………………………………..10 5
Drawing printing settings ………………………………………………………………………………………………………………………………10
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
IV. Introduction of main interface window of the software
………………………………………………………………………………………….10 1 Main menu
…………………………………………………………………………………………………………………………………………………..11 2
Files…………………………………………………………………………………………………………………………………………………………….12 3
Print…………………………………………………………………………………………………………………………………………………………….14 3.1 Open
the task list ………………………………………………………………………………………………………………………………..16 3.2
Historical task list ……………………………………………………………………………………………………………………………….17 3.3
Task attributes…………………………………………………………………………………………………………………………………….18 4
Settings………………………………………………………………………………………………………………………………………………………..19 5
Calibration …………………………………………………………………………………………………………………………………………………..21 5.1
Introduction tonozzle detection
function………………………………………………………………………………………………..23 5.2 Introduction to level
detection function ………………………………………………………………………………………………………..24 5.3
Introduction to vertical detection function
……………………………………………………………………………………………..25 5.4 Introduction tostepping
calibration function…………………………………………………………………………………………..25 5.5 Introduction to
print head horizontal spacing calibration …………………………………………………………………………26 5.6
Introduction toprint head vertical spacing calibration
……………………………………………………………………………..27 5.7 Introduction to bidirectional
calibration function ……………………………………………………………………………………29 5.8 Introduction to
trapping printing calibration function ……………………………………………………………………………..30
6Voltage window …………………………………………………………………………………………………………………………………………….31
7.Advanced ………………………………………………………………………………………………………… Error! Bookmark not
defined. 7.1 Version information
…………………………………………………………………………………………………………………………….33 7.2
Upgrade……………………………………………………………………………………………………………………………………………..34 7.3
Sharpening over printing ……………………………………………………………………………………………………………………..35 7.4
Broken hole compensation …………………………………………………………………………………………………………………..42
8Logs…………………………………………………………………………………………………………………………………………………………….. 45
9.Shortcut button……………………………………………………………………………………………………………………………………………..46 10
Status bar……………………………………………………………………………………………………………………………………………………47
V.Factory mode ………………………………………………………………………………………………………………………………………………………48
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
2 Boot initialization …………………………………………………………………………………………………………………………………………51
3X motor ………………………………………………………………………………………………………………………………………………………..52 4Y
motor ………………………………………………………………………………………………………………………………………………………..53 5Ink
stack……………………………………………………………………………………………………………………………………………………….55 6 Blade
…………………………………………………………………………………………………………………………………………………………..56 7 Print head
combination………………………………………………………………………………………………………………………………….57 8 Print
mode……………………………………………………………………………………………………………………………………………………57 9Reference
trapping…………………………………………………………………………………………………………………………………………58 10Automatic
cleaning………………………………………………………………………………………………………………………………………59 11Manual
cleaning…………………………………………………………………………………………………………………………………………..60 12.Automatic
flash spray………………………………………………………………………………………………………………………………….61 13Running
machine …………………………………………………………………………………………………………………………………………62 14Paper feeding
………………………………………………………………………………………………………………………………………………63 15 Other
…………………………………………………………………………………………………………………………………………………………65 16Import / export
firmware ………………………………………………………………………………………………………………………………66
16.1 Import firmware configuration……………………………………………………………………………………………………………66
16.4 Exporting firmware parameters…………………………………………………………………………………………………………..69
VI.Button board operation instructions
……………………………………………………………………………………………………………………..69 1. Keyboard board button
layout as shown below ……………………………………………………………………………………………….69 2. Menu item
description ………………………………………………………………………………………………………………………………….71 3. Menu list
…………………………………………………………………………………………………………………………………………………….71
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
I. Printing software Developed by Hosonsoft, PrintExp software is a kind of
control software that works with printer. It features user-friendly interface,
simple operation and meets the needs of end users and manufacturers. It is
mainly used for printer control, printer calibration, program upgrade and
update, import and export of parameters, saving of parameters to the board. In
order to enable users to quickly and comprehensively understand the printing
software, get familiar with the various functional operations, precautions and
possible problems, the following is an introduction to the different kinds of
printing software. II. Software start and online 1. Start print control
software The PrintExp software can be used directly. First find the PrintExp
software folder, open the folder, find the PrintExp.exe application, and
double-click the program to start the PrintExp software. 2. Software online
settings 2.1 Gigabit NIC judgment Before network connection, first ensure that
the computer’s NIC is Gigabit NIC for normal connection. The difference
between a 100M NIC and a Gigabit NIC is:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Gigabit NIC contains these characters: Gigabit, GBE, 10/100/1000M, RTL8169.
100M NIC contains these characters: Fast Ethernet, 10/100, FE. Enter the
computer device manager, check the network adapter to make a judgment. The
picture shown below is the 100M NIC:
2.2 Network settings For the first time, you must set the network connection
parameters to connect to the network and connect TCP/IP network cable for
network setup. Network setting method: Advanced menu Network settings, you can
see the network settings window at this time, as shown below:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
As the server IP and server port settings have been fixed, you only need to
set the local IP.As shown above, enter 192.168.127.111 in the local IP address
(note that the first three digits can be any number within 1-255 except for
10), click “settings” to complete the setting, check if the network is
accessible. If it still cannot connect, you can address with the following
methods: Go to control panel network and internet view network status and
tasks change adapter settings click Ethernet or local area connection
attributes to display the following window:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Double-click the highlight bar in the above image to enter the following
window:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Enter the same address in the red box above and click OK to complete. Go back
to the main interface window, check the first icon at the lower left corner of
the main interface displayed in green to indicate that it is connected. If it
is still red, it means that it is not online. You can unplug the network cable
and try again to see if it is online. If you still cannot conne ct, check if
the network cable is in good condition. III. Operation steps before the new
board card is used For a new set of board cards and software, the steps before
using:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
1Set the IP address The specific setting method can be seen in the “Software
Online Settings” in “Software Online and Start” above. 2 Motor gear ratio
calibration It is described in the following section “Factory Settings” in
detail 3 Clean print head Ensure that all orifices of the print head can be
inked normally 4 Calibration In the following section, “Calibration” is
described in detail 5 Drawing printing settings In the following section,
“sharpen and print” is described in detail. IV. Introduction of main interface
window of the software The main interface of PrintExp software is as follows:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
The main interface of PrintExp software mainly includes main menu function
area, shortcut button function area, print list function area, task preview
image display function area, print task information function area, status bar,
etc., which are introduced in the following parts. 1 Main menu The menu tree
of the main menu is as follows:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
2 Files
Main menu
Files Print
Settings
Calibration Voltage
Advanced Log
File directory
Task preview Task
information Print task list
Historical task list Task attribute Print head Wsheilteecteiodnge
Rseetgtuinlagr Csoelottrinbgar Fseeatttihnegr Tessettptianpger
Wfhuitnectsitorenak Infkunlocatidoinng fUuVnclitgiohnt Priunstahgeead
Stetpepsting Pdriinsttahnecaed Tdriasptapninceg Bic-adliirbercattiioonnal
cRaeligburlaattieodn voltFaagcetoorfyfset Vseetrtsiinogn Binrfookremnahtioolne
compensatio Sharpnening overTipmrien.ting source…
Click the file in the menu bar to enter the file interface. The interface mainly includes the file directory window, the image preview window, and the picture information display bar is shown below:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
No.
Name
Function description
1
File directory function area Select the folder where the print files are stored
2
Print file preview function Display all print files under the specified print file folder
area
3
Print file information Display print information of the selected print file
display function area
If you select the preview image and right click, the menu list will pop up as
shown below:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
No.
Name
1
Re-preview
Function description Regenerate a preview of the currently specified print file
2
Refresh
the Refresh all the print files in the specified print file folder
directory
3
Delete files
Delete print files
Add the current print file to the print task list and print immediately
4
Print now
5
Add to print
Add the selected print file to the print task list
6
Open directory
Open the folder corresponding to the print file
3 Print
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Click Print in the menu bar to enter the print interface, as shown below:
No.
Name
Function description
1
Main menu function area Display the area of the main function buttons of the system
2
Shortcut button function Display the area of frequently used command buttons
area
3
Task list function area
Display the current area of all tasks that are being printed or to be
printed
4
Task preview display Display the area of preview of selected print task function area
5
Print task information Display the area of all print information for the current print task
function area
6
Status bar
Display the area of current working status or connection status of the system
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
The print interface includes a print task list window, a history task list
window, a print task preview window, and a print information window; select a
task in the print task list, right click topop up the drop-down menu as shown
below: 3.1 Open the task list
No.
Name
Function description
1
Start printing
Perform printing
2
Delete task
Delete from print task list
3
Wait for printing Add the current task to the queue to be printed
4
Cancel task
Cancel the printing or cancel the waiting for printing status
5
Move to the top Move the selected task to the top of the task list
6
Move up
Move the print task forward one bit
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
7
Move down
8
Move to the last
9
Clear list
10
Open directory
3.2 Historical task list
Move the print task backward one bit Move the selected task to the end of the task list Clear all tasks in the print task list Open the folder where the print file is located
No.
Name
Function description
1
Add to print
Add a task to the print task list
2
Print now
Add a task to the print task list and print immediately
3
Delete task
Delete task from history print list
4
Clear list
Clear the tasks in the history print list
5
Open directory
Open the folder where the print file is located
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
3.3 Task attributes Double-click a task in the print task list to enter the
task property window of the task, as shown below:
No. Name
Function description
Number of Set the number of times of repeated printing
1
Print settings
copies
Horizontal
Horizontal photocomposing number
photo number Photocomp
2
osing
setting
Vertical photo Vertical photocomposing number
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
number
Horizontal spacing
Vertical spacing
X position
3
Regional printing
Y position Width
Height
Horizontal photocomposing spacing(mm)
Vertical photocomposing spacing(mm)
Loading position in X direction in print files Loading position in Y direction
in print files Print width of selected area in print files Print height of
selected area in print files
4
Task attribute
Include the name of the task, the print precision of the task, the size of the print job, the number of color of print tasks, and the number of pass of task.
4 Settings Click settings in the menu bar to enter the settings interface, as shown below:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
No.
Name
Function description
Nozzle
1
selection
Only specific model can have nozzle selection
2
X white
edge
Set loading position
Print speed Set the print speed to be low, medium and high speed
Print direction
Set the print direction to be leftwards printing, rightwards printing and bi- directional printing
3
General setting
Flash work Set flash work on or off before printing before
printing
Automatic cleaning
Set automatic cleaning on or automatic cleaning off
Color bar Set the color bar position to be left color bar, right color bar and
4
Color bar setting setting
color bars on both sides or color bar off
Color bar Difference between two kinds of color bar modes
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
mode
Color bar Set color bar concentration to be weak, medium and strong concentratio n
Color bar Width of color bar width
Color bar Blank spacing between color bar and print picture distance
Feather
Feather range selection
5
Feather setting
range
Feather type Feather type selection
6
Ink loading
function
Put inking loading function on or off
7
Test paper
function
Click “start test” to test the width of printing paper
Stepping Enable white streak, follow PASS feeding in vertical white
white streak streak
8
White streak function
Continuous Enable white streak, follow continuous feeding in vertical white white streak streak
Close white Close white streak function
streak
5 Calibration
Click Calibration in the menu bar to enter the calibration interface, as shown below:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
No.
Name
Function description
Nozzle detection
Check whether the ink jet of orifice of the print head are in good condition
1
print head Level detection detection
Check whether the entire nozzle plane of the print head is parallel to the horizontal plane.
Vertical detection
Check whether the print head is skewed.
2
Stepping
calibration
Calibrate stepping parameters and fine-tuning stepping parameters for different pass modes
print head
3
horizontal
print head spacing
range
calibration
Calibrate horizontal spacing between print heads
print head Calibrate vertical spacing between print heads vertical
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
spacing calibration
4
Trapping
printing
calibration
Calibrate the vertical and horizontal location of each passage of print head
5
Bi-directio
nal
calibration
Calibrate bi-directional offset under different speed of bi-directional printing
5.1 Introduction to nozzle detection function
Click “nozzle detection”, the system will print the nozzle detection pattern,
such as the print head state diagram of EPSON DX5 printer, as shown below:
Partially enlarge the normal and abnormal conditions of the black state diagram, as shown below:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
The state diagram in the above picture may be blocked and needs to be cleaned
until the nozzle inkjet is optimal. 5.2 Introduction to level detection
function
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Click “level detection”, the system will print out the level detection
pattern, such as the level detection pattern of EPSON DX5 printer, as shown
below:
5.3 Introduction to vertical detection function Click “vertical detection”.
The system will print a vertical detection pattern, such as the vertical
detection pattern of EPSON DX5 printer, as shown below:
The calibration chart on the right side of the figure above needs to be
adjusted vertically until the vertical calibration chart is in the correct
state. 5.4 Introduction to stepping calibration function Click “print
calibration chart” under the reference stepping box. The system will print.
For example, the stepping calibration chart of EPSON DX5 printer is as
follows:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
The above figure shows that the stepping is calibrated and the reference line
and the tick mark are completely coincident at 0. If the stepping is not
calibrated, the following situation will appear:
The above picture needs to be adjusted. Adjustment window is as shown below.
Input the adjustment value, click calculation, and reprint the calibration
chart until the baseline and the print line completely coincide at 0.
5.5 Introduction to print head horizontal spacing calibration Click “Print
left/right calibration chart” under the horizontal spacing calibration box of
the print head. The system will print.
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
The above figure shows that the horizontal distance between the print heads is
normal, and when the horizontal spacing of the print heads is not calibrated,
the following picture will appear:
The above picture needs to be adjusted. The adjustment window is shown below.
After inputting the adjustment value in the position H2 in the figure below,
reprint the calibration chart until the mark of 0 is pointing to 0.
5.6 Introduction to print head vertical spacing calibration
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Click “print calibration chart” under the vertical spacing calibration frame
of print head. The system will print.
The figure above shows that the longitudinal distance between the print heads
is normal. All the lines in the 0-point scale box are parallel, and the left
arrow points to the 0-point scale mark. If the longitudinal distance is not
calibrated, the following picture will appear:
All the lines in the 0-point scale box are not parallel, but all the lines in
the -4 scale box are parallel, so it needs to be adjusted. Subtract 4 from the
original calibration value, and then re-calibrate until all the lines in the
0-point scale box are are parallel. The adjustment window is as follows:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
5.7 Introduction to bidirectional calibration function Click “print
calibration chart” under the bidirectional calibration interface, the system
will print
The figure above shows the calibration. The uncalibrated situation is as
follows:
The calibration value must be filled in and recalibrated, as shown below:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
5.8 Introduction to trapping printing calibration function Click “Print
left/right calibration chart” under the color calibration interface, the
system will print
The figure above shows the calibration. The uncalibrated situation is as
follows:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
The calibration value must be filled in and recalibrated, as shown below:
6Voltage window Click the main menu voltage to enter the voltage window, as
shown below:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
No.
Name
Function description
1
Voltage regulation voltage offset
Set the offset voltage of the specified print head channel
2
Refresh voltage Update current print head channel voltage value
3
Set the voltage
Save the current print head voltage offset value
head Display the specified print head temperature
4
temperature (read
only)
7. Advanced Click Advanced on the main menu to enter the advanced interface, as shown below:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
No.
Name
Function description
1
Manufacturer setting
Enter the entrance of the manufacturer parameter setting interface
Display system board card related version information
2
Version Information
3
Rip over printing Select the precision mode for rip over printing
4
Advanced settings
Broken hole compensation, network configuration, installment authorization settings
7.1 Version information
Click the version information in the advanced interface and enter the following interface:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
7.2 Upgrade The mainboard logic, the sweep logic, the motherboard program, and
the MCU program can be upgraded and updated separately. After the program is
upgraded, the power must be turned off and then powered back on. Click refresh
to check whether the newly upgraded program has been updated. The upgrade
method is as follows: Click the “Upgrade” button above to pop up the following
window:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Select the program to be upgraded, and then click the “Open” button to enter
the upgrade window. Click “OK” to enter the upgrade. The upgrade will prompt
whether the upgrade is successful. After upgrade, power back on again, check
the version information to confirm that it has been upgraded. 7.3 Sharpening
over printing In the advanced interface, click the sharpening over printing
button to enter the following interface:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
No.
Name
Function description
1
Basic setting
Buffer ratio Port number
Indicate that RIP reaches the set value and start printing Default value: 9100
RIP software determines the printing mode in the case of
Determined by RIP RIP over printing
2
Printing mode
software
Determined by RIP Printing control software determines the printing mode in
software
the case of RIP over printing
How does printing software set printing mode
Open the printing software, add the print task to the print list, click the print mode drop-down list of the print task, select different print modes, as shown below:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
No.
Name
1
VSD_L
2
VSD_M
3
VSD_EXT1
4
VSD_L_H
Function description For normal mode large dot printing, the effect is as
shown in Figure 7-3-1 Normal mode midpoint printing
Normal mode extension point printing
For horizontal connected large dot printing, the effect is as shown in Figure
7-3-2
5
VSD_L_V
For longitudinal connected large dot printing, the effect is as shown in Figure 7-3-2
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Normal mode Figure 7-3-1
Horizontal connection Figure 7-3-2
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
How to set the print mode by Maintop Rip software Open Maintop software
maintop-file – create new file – load picture – print, pop up the following
window
Click the “Printer Settings” button in the above figure to set the print mode
and enter the red box as shown below.
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Click the “More Options” button in the above figure to set the printing
precision, and select the printing precision from the precision drop-down
list, as shown below.
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
How to set the print mode by Honson Rip software Open Honson Software
UltraPrint – New Canvas – Place Image – Print Canvas, enter the settings
interface, as shown below:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
The red box in the figure is the setting for the precision and print mode. 7.4
Broken hole compensation In the advanced settings menu, click the broken hole
compensation button to enter the following interface:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
No.
Name
Function description
Broken
hole
treatment method
Broken hole treatment method selection
1
Check the broken hole status of each orifice of the print head
2
Broken
hole
detection
All orifices opening/closing options
3
Enable all orifices
4
Save and exit
Save the current settings and exit the broken hole settings.
5
Cancel and exit
Don’t save the current setting and directly exit the broken hole setting
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
state
Right click the orifice setting interface to pop up a drop-down menu, as shown
below:
No.
Name
Function description
Select the whole row at the same time
1
Select whole row
Unselect the whole row at the same time
2
Unselect the whole row
Select the whole line at the same time
3
Select the whole line
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Unselect the whole line at the same time
4
Unselect the whole line
Select the whole page at the same time
5
Select the whole page
Unselect the whole page at the same time
6
Unselect the whole page
8Logs Click the log button in the lower right corner of the printing software to enter the log window, as shown below:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Through this window, you can see the current operation, especially when there
is an error or a fault, you can know which type of error information is
generated by viewing the debugging information, so that the error is solved in
a targeted manner.
9. Shortcut button
Shortcut button
Function description Printing start button to execute the print command print head check button to execute print head printing state Printing pause/resume button Printing cancel button to execute the end printing command print head cleaning button to execute print head cleaning command Flash spray on/off button White edge positioning button Moisturizing off/on button Reset button XX mmoottoorr lreigfthsthsihfitfbt ubtutottnon Feed button Return button Stepping fine adjustment reduction button
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Stepping fine adjustment increase button Two-way fine adjustment reduction
button Two-way fine adjustment increase button
Entry into height measurement control panel button
10 Status bar
Status bar icon
Description Network cable normal connection
Network cable disconnection
Offline
Turn on the flash spray
Turn off the flash spray
System functions normally
System error System warning Offline Normal print head temperature
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Abnormal print head temperature print head temperature warning Offline
V. Factory mode Click the factory settings in the advanced interface, enter
the password directly, enter the factory mode, as shown below:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
1. Main content of factory mode The main content of factory mode refers to
the following menu tree
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Print mode
Configuration mode list
Feather setting White edge offset
Csoelottrinbgar concentration Rassteerttsinetgting
WavCeofonrtminuseedtting
Other settings
printing after Ink srehsourmtaignegtest
connection Sharpseetntiinngg over
Mopirsitnutrinizging
Peanpaebrlifnegedswmitocdhe
Paper feed setting
befPoarpeearnfdeeadfter distpanricnetibnegfore anPdaapfetrermparrigntining
setting Paper test setting
pass number
Positioning metGhoeadrsrealteicotion Strockaelibpraartaiomneter Sportssepttairnagmeter
paper feed mode X motor setting
setting Raster test
Motor stroke
Ink stack setting
setting Ink stack
parameter setting X motor initial
Motor initialization
setting
paYrammoettoerrisneittitainl g parBalmadeetemr soettotring initial parameter
Motor
Blade motor
Mosteotrtisntgroke parameter setting Blade parameter
Factory mode
setting
Inksescttrianpging
cleaning position
Basic trapping
Automatic cleaning Mapnauraal mcleetaenring
Y motor setting Basic trapping paCrlaemaneitnegr mseottdieng
Flassehttsinpgray setting before andFalafstehrspprrianyting
Gseeatrtirnagtio calibration Stroke parameter
setting Sports speed
setting Positioning method selection
parameter Print head combination
settiPnrginitnhperaindting combination
UV lpigahratmeneatebrling
UV light control
control UV light lighting
parameter Running machine
mode Compensating dAiusttoanmcaetsicetftlainsgh
Automatic flash
spray
Add: Room 1703, Building C6, HengsfepnrgayInpdaursatrmiael tCeirty, XixianMg Santrueeatl, fBlaasoh’an District, Shenzhen
Tel: 86-0755-2894 0020
Fax: 27961549
spray http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
2 Boot initialization Perform the motor’s action parameters during power-on
initialization, as shown below:
The parameters of the X motor, the Y motor, and the blade motor are the same. The X motor is taken as an example for explanation. See the following table:
No. Name
Function description
1
Acceleration and deceleration distance
Acceleration and deceleration distance
2
Origin
reverse
movement distance
The distance the motor moves away from the origin
After the motor moves to the origin direction, the distance of the reverse
Returning to the movement after hitting the limiter
3
zero position after
hitting the limit
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
4
Motor moving speed Motor moving speed
3X motor The settings of the X motor parameters are as follows:
No. Name
Function description
1
Gear ratio calibration
Calibrate the gear ratio of the X motor
2
Stroke parameters
The maximum range of motion of the X-direction trolley
Acceleration
3
and deceleration
Acceleration and deceleration distance
distance
4
Reset speed
The speed of the trolley movement during the reset
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
5
Regular moving speed
The speed of trolley when moving to the left and right in manual mode
Invalid running The back running speed of trolley in one-way printing
6
speed
of
printing
7
Print speed
The ratio of the maximum spray frequency to the speed, the difference of the different speeds
Raster test has two main functions: First, it is confirmed whether the
precision of the grating is accurate by comparing the set offset distance with
the raster value reported in real time; in addition, determining whether the
8
Raster test
direction of the raster is correct
9
Pulse positioning
Locate the current position of the trolley by pulse
Locate the current position of the trolley through the raster
10
Raster positioning
4Y motor
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
No.
Name
Function description
Calibrate the gear ratio of the Y motor
1
Gear
ratio
calibration
2
Stroke parameters
The maximum range of motion of the Y-direction motor
The motor accelerates from the stop state to the constant speed or
Acceleration and decelerates from the constant speed to 0.
3
deceleration
distance
The speed of the Y motor at a constant speed during manual feed/return
4
Conventional feed speed
movement
5
Printing speed
The ratio of the maximum jetting frequency to the speed, the ratio of the different speeds varies.
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
5Ink stack
No. Name
Function description
1
Motor stroke setting Maximum range of motion of the ink stack
2
Acceleration and deceleration distance
Acceleration and deceleration distance
3
Ink stack movement speed
Ink stack movement speed
4
Moisturizing stack height
ink The height of the ink stack in a moisturizing state
5
Flash inkjet height
stack
The height of the ink stack in the flash spray state
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
6
Scrape height
ink
stack
The height of the ink stack when it is moisturized
When entering the limit detection, the height of the ink stack (the height is
7
Limit detection ink as small as possible, but it must be out of the limit position) stack height
6 Blade
No.
Name
Function description
1
Motor parameters
stroke Setting of the maximum stroke parameter of the blade motor
Blade motor acceleration/deceleration distance parameter and
motion speed parameter setting
2
Blade parameter setting
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
The starting position of the trolley when the scraper is
3
Start position of ink scraping the print head scraping
The end position of the trolley when the scraper is scraping the
4
End position of ink print head scraping
7 Print head combination
Show a variety of different arrangements of multiple print heads. 8 Print mode
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
No.
Name
Function description
1
Configuration list
Currently configured all precision list of the print head
2
Mode list
List of print modes for each precision
Feathering amplitude setting and feathering point
3
Feathering setting
mode mode selection
9Reference trapping
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
The trapping color value here is used to fill the internal trapping color
shift of the print head. 10Automatic cleaning
No.
Name
Function description
1
Cleaning mode Automatic cleaning on/off selection
2
head
combination
Selection of combined cleaning between different print heads
3
Cleaning
When the flash spraying printing is on, the flash spray is carried out
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
interval
after each set number of passes.
The number of times the print head ejects per second
4
Flash spray frequency
5
Flash times
spray Stop the flash spray after several flash spray cycles in succession
One flash spray cycle, continuous flash spray time
6
Single flash spray time
Two flash spray intervals
7
Flash spray interval time
11Manual cleaning
No. Name
Function description
1
Number of pumping
ink
Number of ink pumping during manual cleaning
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
2
Ink time
pumping The duration of each ink pumping
After the ink pumping is completed, wait for the set time before proceeding to
3
Static time after the next operation. ink pumping
Waste
Start time to pump waste ink from motor ink
pumping time
Trolley removal In sliding flash spray, the speed of movement when the trolley moves to the
speed
specified position
Trolley removal distance
The flash spray position in sliding flash spray
12. Automatic flash spray
No. Name
Function description
1
Automatic flash spray frequency
The number of inkjet ejections per second during automatic flash spray
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
2
Single spray time
flash
One flash spray cycle, continuous flash spray time
Interval between two flash sprays
3
Flash
spray
interval time
4
Automatic waste ink pumping cycle
During the automatic flash spray process, carry out one waste ink pumping after setting flash spray times
Start time to evacuate the waste ink motor
5
Waste
ink
pumping time
13Running machine
No. Name
Function description
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
The starting
1
position of the The starting position of the trolley when running the machine
trolley
The maximum The end position of the trolley when running the machine
2
position of the
trolley
The distance of paper feeding of one round of trolley movement in the Y
One-way
direction
3
paper-feeding
distance
The total distance of the paper feeding in the Y direction in the machine
Maximum
running
4
paper-feeding
distance
5
Blade removal The distance the blade is removed from the origin of the blade during the
position
running
14Paper feeding
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
No.
Name
Function description
1
Paper feed printing
mode
before
Paper feed mode selection before printing
2
Paper feeding printing
mode
after
Paper feed mode selection after printing
3
Paper feeding before printing
distance Set distance of paper feeding before printing
Paper return distance before printing
Set distance of paper return before printing
4
Paper feeding distance after Stop printing after the printing task is completed and paper
printing
feeding distance is set
Paper return distance after Stop printing after the printing task is completed and paper
printing
return distance is set
8
Fine adjustment of left margin and right margin of paper
Fine adjustment of the distance between the drawing to be printed and paper edge
9
Paper detection
Turn on/turn off paper detection of paper shortage detection
10
Test paper sensor offset
The horizontal distance between the test paper sensor probe and the raster decoder
11
Test paper non-detection area
The distance of the test paper sensor detection probe to the paper start mark
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
15 Others
No.
Name
Function description
The distance from the print head to the printed material
1
X white edge start offset
White edge positioning error setting, its calculation formula:
white edge positioning value – white edge positioning offset=
2
X white edge positioning white edge value + white edge starting offset offset
3
Raster setting
Set the precision of the grating (precision after four-way frequency)
4
Color bar concentration
The color bar concentration of different grades set different
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
proportions
5
Waveform
Waveform selection
6
Timeout in printing
In the print, the dropout time reaches the set time and print pauses
7
Automatic recovery time After the pause, the network cable is detected to be connected
after pause
within the set time, and the printing resumes automatically.
Select the action to be taken when the ink is in shortage
8
Ink shortage detection
9
Moisturizing
Turns on/off moisturizing function
16Import / export firmware
16.1 Import firmware configuration
Click “Firmware Menu” to pop up the drop-down menu list and select “Import
Firmware Configuration” to select the firmware configuration to be imported.
Note the suffix is ..bsf, as shown below:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Click “Open” to enter the import firmware configuration state. At this time,
you should not do anything. You will be prompted to “Import successfully” and
view the debugging information. The message “Loading Flash successfully”
indicates that the import is successful. 16.2 Import firmware parameters Click
“Firmware Menu” to pop up the drop-down menu list and select “Import Firmware
Configuration” to select the firmware configuration to be imported. Note that
the suffix is .xtf, as shown below:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Click “Open” to enter the import firmware configuration state. At this time,
you should not do anything. You will be prompted to “Import successfully” and
check the debugging information. The message “Load parameter is successful”
indicates that the import is successful. 16.3 Exporting firmware configuration
Click “Firmware Menu” to pop up the drop-down menu list, select “Export
Firmware Configuration”, save it in the specified directory, note that the
suffix is .bsf, as shown below:
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Click “Open” to enter the export firmware configuration state. At this time,
you should not do anything. You will be prompted to “export successfully” 16.4
Exporting firmware parameters Click “Firmware Menu” to pop up the drop-down
menu list, select “Export Firmware Parameters”, save it in the specified
directory, note the suffix is.xtf, click “Open” to enter the export firmware
parameter status. No action should be done at this time and you will be
prompted “export successful” later. VI. Button board operation instructions 1.
Keyboard board button layout as shown below
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an
District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549
http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Button function list description
No. Button name Button function description
1
QUALITY
Feathering settings
2
CLEANING Print cleaning
3
CANCEL
Print cancel
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
4
PAUSE
Print pause
5
ORIGIN
Reset to original point
6
NOZZLE TEST
Print head status
7
UP
Return
8
DOWN
Feed
9
LEFT
Left shift
10
RIGHT
Right shift
11
MENU
Menu
12
ENTER
Confirmation
13
POWER
2. Menu item description All the functions of the menu items have been
introduced in the print software setting interface or the manufacturer mode,
and will not be described here.
3. Menu list
Add: Room 1703, Building C6, Hengfeng Industrial City, Xixiang Street, Bao’an District, Shenzhen Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
Shenzhen Hosonsoft Co., Ltd.
No.: HS/D-YF-A0-005
Print head
print head selection
Cleaning mode setting
selection Cleaning method
Close Flash spray
Print head maintenance
Automatic cleaning switch
Ink loading Tessetttpianpger
cleaning Weak cleaning
Medium cleaning
Strong cleaning
Papefrufnecetdiobnefore printing
Printing speed
Low speed Medium speed
High speed Single-direction
Printing direction
Singleleft-wdairredcstion Bir-idgihrtewctairodnsal
Print setting
Color bar width Color bar distance
Color bar position
printing Left side of figure
Right side of Bothfigsuidrees of
figure Close
Color bar mode
Flash spray before printing
Color bar concentration
Mode 1 Mode 2
Weak Medium Strong Main board
seSrpiaral ynuswmebeepr
Msaeinriablonaurmd bloegric
Menu
Version information
Sprayvewreseiopnlogic Mavienrsbioonard procedure
firmMwvaBaeiunrrtesbtiooovannerrdsion procedure
System setting
Restore factory setting
vCearnscioenl Confirm Exit advanced
Advanced mode
Startmcoodpeying
mode Language
Nozzle
Print head inspection
inspection Level inspection
Vertical
Prinintscpaelcibtiroantion
Reference
Caflibgruarteion
stepping
Calibration
calibration
Comvpaluuteing
parameter
Leftwvaalrudes level
Print head
Risgphatvwinagrds
spacing
level spacing
Material selection
calibration
Vertical spacing
Add:
Room
1703,
Building
C6,
Hengfeng
Industrial
City,
XixBiai-ndgirSetcreteiot,nBaal o’an calibration
DistrSicptP,eSreehdceisnseziothteninng
Tel: 86-0755-2894 0020 Fax: 27961549 http://www.hosonsoft.com
setting
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>