shadeomatic Roller Skyline 2-in-1 Coupling Shade Instruction Manual
- June 4, 2024
- shadeomatic
Table of Contents
shadeomatic Roller Skyline 2-in-1 Coupling Shade
INSTALLATION INSTRUCTIONS
Important: Be sure to get familiar with the Roller Shades – Skyline
Fascias installation instructions before continuing.
Make sure the mounting surface is level. Brackets must be in line and level
for shade to operate properly. Shim brackets if necessary.
Identify the Shade and Define Shades and Bracket Positions
On Fascia 3 and 4” System, the edges brackets (A and C) are the same. On the Spring Ring and Drop in systems, the “A” bracket should be placed on the edge at the motor side. The “C” brackets should be installed at the idle edge. The Intermediate Brackets (B) should be located between shades.
Install the First Shade
Install the first shade brackets following the same steps as a regular shade
(Please refer to Roller Shades – Skyline Fascias installation instructions).
First, assemble the Intermediate Bracket Disc into the intermediate bracket.
Rotate the disc 1/4 turn to lock into place. Then, place the spring loaded pin
end into the round hole of the intermediate bracket. Keeping the pin end
secure in its bracket, insert the hooks straight into the two slots in the
outer bracket.
Once the two hooks are through the slots, gently pull downward until the two
hooks have locked securely to the bracket’
Install the Second Shade
Install the final regular bracket aligned and leveled with the others. Place
the spring loaded pin end into the round hole of the intermediate bracket.
Keeping the pin end secure in its bracket, insert the hooks on the clutch
straight into the two slots in the bracket. Once the two hooks are through the
slots, gently pull
downward on the side with two hooks until the two hooks have locked securely
to the bracket.
Install the Fascia
See more detail on Roller Shades – Skyline Fascias installation instructions.
Drop In – Install the Motorized Shade
Note: Illustration shown under Open Roll without top treatment, same
concept applies to Fascia & Pocket.
Install the shade with the motor brackets (A and B ) following the
steps in the provided Roller Shades Installation Instructions.
Important: The intermediate bracket foot must point away from the motor
bracket.
Drop In – Install the Second Shade
Note: Illustration shown under Open Roll without top treatment, same concept
applies to Fascia & Pocket.
Install the final bracket (C) level and aligned to the other brackets,
following the steps in the provided Roller Shades Installation Instructions.
Place the spring loaded pin end into the round hole of the bracket (C).
Keeping the pin end secure in its bracket, insert the fork side of the shade
to the bronze bushing. While holding the motor side shade to make sure it does
not come loose, lock the fork from the idler side shade into the tang at the
intermediate bracket (B).
Spring Ring – Install the Motorized Shade
Note : Illustration shown under Open Roll without top treatment, same
concept applies to Fascia & Pocket.
Install the shade with the motor brackets (A and B) following the steps in the
provided Roller Shades Installation Instructions.
Once the brackets are installed, rotate the roll to ensure reset button of the
motor is facing down. Place the spring loaded pin end into the round hole of
then Idler bracket. Then, keeping the pin end secure in its bracket, align and
insert the motor head into the slots in the motor bracket. Lastly, once the
motor is completely secured into the motor bracket, snap the ring retaining
clip in place, locking the motor in position.
Spring Ring – Install the Second Shade
Note: Illustration shown under Open Roll without top treatment, same concept
applies to Fascia & Pocket.
Install the final bracket (C) level and aligned to the other brackets,
following the steps in the provided Roller Shades Installation Instructions.
Place the spring loaded pin end into the round hole of the bracket (C).
Keeping the pin end secure in its bracket, insert the fork side of the shade
to the bronze bushing. While holding the motor side shade to make sure it does
not come loose, lock the fork from the idler side shade into the tang at the
intermediate bracket (B).
Removing the Shade (Only If Necessary) — Removing the Fascia
First, rotate upward to disengage the fascia. Then, gently pull up the control unit (Clutch, Motor or Spring) until the hooks touch the top part of the bracket slot. Pull the shade towards the spring loaded pin end until the hooks are complete out of the bracket slots. Finally, remove the spring loaded pin end from the idler bracket.
Removing the Shade (Only if Necessary — Spring Ring
Note: Illustration shown under Open Roll without top treatment, same
concept applies to Fascia & Pocket.
First, raise the shade. Remove the ring retaining clip in place from the
motor. Then, slide the roll towards the spring loaded pin end until the motor
head are completely out of the motor head slots. Lastly, remove the spring
loaded pin end from the Idler bracket.
Child Safety
Young children can STRANGLE in cord loops and in the loop above the cord stop. They can also wrap cords around their necks and STRANGLE.
-
Always keep cords out of children’s reach.
-
Move cribs, playpens and other furniture away from cords.
Children can climb furniture to get to cords. -
Do not tie cords together.
-
Make sure cords do not twist together and create a loop.
Warranty
STRANGULATION HAZARD –
Young children can be strangled by cords Immediately remove this product if a
cord longer than 22 cm or a loop exceeding 44 cm around becomes accessible.
Rev 7/21 Print 7/21
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>