ICE iW90 Wet Dry Vacuum Cleaner Instruction Manual

ICE iW90 Wet Dry Vacuum Cleaner

IMPORTANT: To ensure full warranty protection, Please fill out & return your warranty card.

Please fill out at the time of installation for future reference.

• Model No.
• Serial No.
• Machine Options
• Sales Rep.
• Sales Rep. phone no.
• Customer ID Number
• Installation Date

HOW TO ORDER PARTS

Only use ICE Cobotics Company supplied or equivalent parts. Parts and supplies may be ordered online,by phone, by fax or by mail.

1. Identify the machine model.
2. Identify the machine serial number from the data label.
3. Ensure the proper serial number is used from the parts list.
4. Identify the part number and quantity. Do not order by page or reference numbers.
5. Provide your name, company name, customer ID number, billing and shipping address, phone number and purchase order number.

PROTECT THE ENVIRONMENT

Please dispose of packaging materials,old machine components such as batteries, and hazardous fluids, including antifreeze and oil, in an environmentally safe way according to local waste disposal regulations.

IMPORTANT: To ensure full warranty protection, Please fill out & return your warranty card. Always remember to recycle

ICE Cobotics (GuangDong) Company Limited

• XiangShi Road LiaoBu DongGuan GuangDong China
• Tel:0769-8186 9000
• Fax:0769-8186 3000

SAFETY PRECAUTION

Carefully read and understand this manual before operating this machine.

This machine must be grounded! This machine shall be grounded while in use to protect the operator from electric shock. Grounding provides a path of least resistance for electric current. This machine is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not remove the ground pin under any circumstances. This machine is for use on a nominal 120-volt circuit and has a grounding plug that resembles the plug illustrated in Figure. Make sure that the machine is connected to an outlet having the same configuration as the plug. No adapter should be used with this machine. This machine is intended for commercial use. It is constructed for use in an indoor environment and is nor intended for any other use. Use only recommended accessories.

Do not operate the machine:

• Unless trained and authorized.
• Unless you have read and
• Inflammable or explosive areas. understand the operator’s manual.
• With a damaged cord or plug
• With the use of extension cords.
• If not in proper operating condition.
• In outdoor areas and standing water.

Before operating the machine:

• Make sure all safety devices are in place and operating properly.

When using a machine:

• Do not run the machine over the cord.
• Do not pull the machine by cord or plug.
• Do not pull cord around
• Do not unplug by pulling on the cord. sharp edges or corners.
• Do not stretch the cord.
• Do not handle plug with wet hands.
• Keep the cord away from heated surfaces.
• Report machine damage or faulty operation immediately.

Before leaving or servicing the machine:

• Turn off the machine.
• Unplug the cord from the outlet.

When servicing machine:

• Unplug the cord from the outlet.
• Use manufacturer-supplied or approved replacement parts

To avoid electrical shock,please replace the power cord immediately if any damage is being detected. The replacement must be performed only by an authorized person or by our customer service center.

Handle Assembly Instructions

Attaching Handle

1. Remove the handle from ship position (Figure 1).
2. Realign handle as shown and screw knobs (Adjustable handle has three height](Figure 2).
3. Attach Drain hose (Figure 3).
4. Attach front mount squeegee (Figure 4).

Operation of Wet & Dry Vacuum

Read operators manual thoroughly prior to operating or servicing this machine. Be sure that the handle is properly assembled on machine body prior to operating.

Wet Operation

1. Remove clear window and remove the cloth or paper filter form the vacuum.
2. While clear window is removed, check to make sure that the float shut-off is unobstructed and fully functional.
3. Replace clear window on the top of the recovery tank.
4. Connect the vacuum hose to inlet on the machine body.
5. Attach appropriate accessory tool for the job to be completed.
6. Make sure the Main Power Switch is in the OFF position, then plug power cord into a grounded outlet. Do not use an extension cord in conjunction with the standard power cord.
7. If using the front-mounted squeegee assembly, be sure that the squeegee is attached to front of the machine.
8. If using the front-mounted squeegee assembly, lower squeegee to the floor by depressing the left half of the pedal [rear of the machine] forward with your foot.
9. Turn power switch to “on” position.
10. During wet pickup, the float shut-off will automatically prevent water from entering the recovery tank once the recovery tank is full. If foam develops in the recovery tank during wet vacuuming, use defoamer chemical to help eliminate the foam. Foam will not activate the float shut-off, and therefore, may cause vacuum motor damage.
11. To raise the squeegee assembly back to the transport position, depress the right half of the pedal (rear of the machine) downward with your foot.

Dry Operation

1. If the machine has been used for wet pick-up, empty the Recovery Tank, rinse it out and dry it completely and install the Dry Container System. DO NOT use the machine for dry pick-up without the Dry Container System in place.
2. Remove clear window, and be sure the cloth or paper filter is properly installed. Do not operate machine without bag or filter properly installed.
3. Replace clear window on the top of the recovery tank.
4. Connect vacuum hose to inlet on the machine body.
5. Attach appropriate accessory tool for the job to be completed.
6. Make sure the Main Power Switch is in the OFF position, then plug power cord into a grounded outlet. Do not use an extension cord in conjunction with the standard power cord.
7. Turn power switch to “on” position.
8. Check the filter bag periodically to see if it is full. For optimal performance, replace bag when it is 3/4 full.

DRAINING THE RECOVERY TANK

1. Unplug machine from power outlet.
2. Transport machine to nearest floor drain of bucket.
3. Remove drain hose form rear of machine. Remove ball plug from drain hose, and drain the contents of the tank.
4. After the contents have drained, remove the clear window and rinse recovery tank with clean water.
5. Replace the ball plug on the drain hose and hang hose back on the rear of the machine.

To prevent odors in the recovery tank, remover the vacuum head when machine is not in operation to allow air to circulate.

MAINTENANCE

To keep the machine performing well for many years, please follow the following maintenance procedures. Always confirm that the machine is unplugged prior to performing any maintenance or repairs.

1. Unplug machine as soon as you are done using it.
2. Check power cord for any damage. If any damage is detected, replace the cord immediately.
3. Lubricate casters with a water resistant lubricant every month
4. Check machine for loose or missing nuts and bolts, and replace as necessary.
5. Check the filter, and clean it after each use
6. Remove the vacuum hose and check it for any holes and clogs
7. Clean the outside of the machine with a mild cleaner

STORAGE

1. Unplug machine from power source and wrap cord on handle.
2. Store in upright position in a dry area.
3. Store with squeegee assembly off the ground.
4. Store with clear window off unit so that tank may breathe.

MACHINE COMPONENTS

1. Handle
2. Crevice Tool
3. Knob
4. 10″ Wheel
5. 3.5″ Caster
6. Front mount squeegee
7. Hose Assy
8. Tank
9. Clear Window
10. On/off switch
11. Drain Hose 1
12. Pedal
13. Wire Hook

PARTS LIST

36

| 2310121A| Vac Motor,3-Stg,120V,With Terminal| 000101-000150;000153-000592;105360-| 1
8011025A| Vac Motor,2-Stg,120V,With Terminal| 000593-003583;103584-105359| 1
37| 2310122| Stud,Vac Motor 3-Stg| Match the serial number of Vac Motor 3-Stg| 3
8112006| Stud,Vac Motor 2-Stg| Match the serial number of Vac Motor 2-Stg| 3
38| 1121605| Nut, M6|  | 3
39| 2310116| Gasket,Vac Motor|  | 1
40| 2310120| Screen|  | 1
41| 2320308A| 2″ Wheel Assy|  | 2

NOTES:

• Use part number 8011025A for all the 2-stage serial numbers
• Use part number 2310121A for all the 3-stage serial numbers.

ACCESSORIES

PARTS LIST

23

| 2330130| Cloth Bag|  | 1
2330132| Paper Bag(optional)|  | 1
24| 2330131| Clip, Cloth Bag(optional)|  | 1
25| 2330134| Catridge Filter|  | 1
26| 1962052| Clamp|  | 1

TECHNICAL DATA

TECHNICAL DATA

Model| iW90
Voltage| 120V
Power| 1000W
Current| 9A
Frequency| 50-60Hz
Capacitor| 90L
Vacuum| 2319mmH2O(91″)
Flow rate| 2910L/Min(104CFM)
Sound pressure level

at workstation

| 70 dB(A)
Weight| 40kg
Length of Power cord| 15m
Dimensions| 117.6cm(L)X45.3cm(W)X110cm(H)

Wiring Diagram

iW90

WEAR &TEAR PARTS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>