SeeEyes SC-IPT1204P 4-ch IP Transmitter

Precaution and Safety Guidelines

The content of this guideline is intended to protect user safety and prevent property damage. Please read this user guide carefully and use the device properly

Warning
(Failure to adhere to any of the following guidelines could result in serious injury or death for someone.)

• Be sure to install the product after unplugging the power cord. Also, do not use many power plugs at the same time.
  • It may cause abnormal heat, fire, and electric shock.
• Do not leave the device in a place where water will fall or splash. Also, do not place anything with water on it, such as a vase of flowers.
  • It may cause malfunction or fire if liquid goes into the device.
• Do not open the lid arbitrarily as this device has a high voltage part inside. Never disassemble, repair, or modify it.
  • By abnormal working, it may cause fire, electric shock, and personal injury.
• Do not install this product in places with high humidity, dust, or soot.
  • It may cause electric shock and fire.
• Always keep the location of the appliance clean during or after installation to prevent dust. Especially when cleaning the device, wipe it with a dry towel and do not use water, thinner or organic solvent.
  • It may damage the case of this device, and cause malfunction or electric shock.
• Keep the device in a cool place that doesn’t let direct sunlight. Keep it at a proper temperature and avoid heating appliances like candles or heaters. Also, keep the equipment or tools away from places where people come and go.
  • It may cause a fire.
• Pay attention to possible hazards in the workplace, such as wet floors, ungrounded power extension cables, old power cords and a lack of safety earth. Consult your place of purchase or professional if problems arise.
  • It may cause fire and electric shock.
• Concerning the input voltage for operating this device, a voltage range must be within 10% of the rated voltage. Also, do not use a heat source such as a hair dryer, iron and refrigerator to the same power unit.
  • It may cause abnormal heat, fire, and electric shock.
• Disconnect the power plug with care during thunder and lightning.
• Do not bend the power cord with excessive force. Make sure the power cord is not crushed by heavy things.
  • It may cause a fire.
• When connecting cables, install a “U” shape in order to prevent rainwater/dew/fog from getting into the product.

Caution
(If you do not keep any of the below guidelines, you may get injured or suffer property loss.)

• Avoid installing near strong magnetic fields or radio waves and wireless devices such as radio or TV.
  • Install in a place that is free from magnetic, radio, or excessive vibration.
• Proper ambient temperature and humidity are recommended.
  • Avoid extremely high temperatures(over 50°C) or low(below -10°C), and humid conditions.
• Do not place heavy items on the product or let foreign substances enter inside the device.
  • It may cause failure.
• Install in a well-ventilated place, and avoid direct sunlight or heat appliance.
• Strong shock or vibration may cause device failure. Be careful when using the device.
  • Install in a place without severe vibration.
• If you notice any unusual noise or smell, unplug the power supply immediately and contact the place of purchase or service center.
  • There may be a risk of fire and electric shock.
• Ventilate the system operating room and secure the main body cover.
  • It may be the cause of the failure by environmental factors.
• Refer the device to the service center and get regular checkups to maintain the performance of the system.
  • We are not responsible for any damages caused by the user’s carelessness.
• Be sure to plug the power cord into a grounded outlet.
  • There is a risk of electrical shock and personal injury.
• Place the power plug in a location that is easy to operate.
  • If a failure of the product occurred, the power plug must be unplugged to power down completely. The power button on the main body does not completely disconnect power.
• Do not use this device in close proximity to a device that produces strong waves such as a radio set(TRANSCEIVER, Walkie talkie, etc.) or repeater. It may affect video signal, or cause disorders such as noise or crack on the screen.
• The transmission medium( CABLE) must be a UTP(CAT.5e) or coaxial cable.
• Be careful not to change the cable array during installation. (Refer to ‘4. CABLE PIN Configuration ’ on page
• Make sure to check the power output of each port when connecting two or more cameras or this product, since the maximum output power of the CAMERA PORT of the product is 30W. The power output is limited depending on the power consumption of the camera.
• UTP(Unshielded Twisted Pair) Cable is for indoor use only. Use an STP(Shield Twisted Pair) Cable which is covered for outdoor use.
• The transmission distance may vary depending on the UTP cable type.
• Refer to the user’s manual for problems or questions besides the above. Contact our service center if you need assistance from a professional technician.

Introduction

Overview

SC-IPT1204P is a hybrid network data transmitter with built-in 4CH PoE HUB and EoC(Ethernet Over Coax.) function. This transmission device transmits Ethernet data from four IP cameras over only one coaxial cable and receives operating power from receivers such as SC-IPR07P or SC-IPR0708H, therefore, it shortens the construction period and reduces installation cost. Also, this item improves the short distance of typical network systems by extending transmission distance up to 500m and supplies power to 4CH PoE Cameras with DC Jack for external power supply.

Features

• 4CH PoE HUB function
• EoC (Ethernet Over Coax) function
• Supports PoE (Camera Side : Endspan x 4CH, NVR Side : End/Midspan x 1CH)
• Supports EoC (when connecting with SC-IPR07P)
• 4 IP cameras transmission over 1 Coax. cable (Max. 8 cameras transmission over one coaxial cable by adding 1pc of transmitter via extra NVR(RJ-45) port provided)
• Provides extension switch for setting bandwidth of CAMERA side
  • Switch On: 10Mbps / Max. 250m (CAT.5e)
  • Switch OFF: 100Mbps / Max. 100m (CAT.5e)
• Power Input: DC 48~56V Adapter (DC Adapter power priority) Supports PoC (when connecting with SC-IPR07P)

Components

The accessories included in the product are subject to change.

Product Parts and Functions

1. CAMERA SIDE: IP camera connection port. PoE Type A supported. (IEEE802.3 af/at)
2. Port to supply power to the camera with PoE or receive camera Data.
3. RX SIDE: SC-IPR07P connection port. PoC(Power over Coax.) supported (when connecting SC-IPR07P)
4. EoC Status LED: IPR07P PoC Link LED, EoC Data LED
5. NVR SIDE: NVR connection port.
6. Bandwidth Select Switch: 100Mbps, 10Mbps setting supported
   SWITCH| Bandwidth| Transmission Distance
   ---|---|---
   ON| 10Mbps| Max. 250m over CAT.5e
   OFF| 100Mbps| Max. 100m over CAT.5e (Default)
   • Please be noted that if the bandwidth exceeds 10Mbps after setting the switch to 10Mbps, a problem may occur with the video.
   • The factory default of the Bandwidth Switch is 100Mbps.
   • When the distance between camera and the CAMERA SIDE port is over 100m, the bandwidth setting is automatically set to 10Mbps. If the automatic setting is not done depending on the specification of the devices, turn the bandwidth switch on manually.
7. DC 48V~56V INPUT: Port to input DC adapter (48V or 56V) power.
   • Please use exclusive DC56V adapter for stable power supply for each PoE port.

POWER, LINK/ACT Status Display LED

EoC Status

LED

| Operation Power| Yellow| On| Operation power OK
EoC Data| Green| Flashing| EoC Data Transmitting & Receiving OK
Cam Side

1X4 RJ45

| PoE Output| Yellow| On| PoE Output OK
Ethernet Data| Green| Flashing| Ethernet Data Transmitting & Receiving OK
NVR Side

RJ45

| Operation Power| Yellow| On| Operation Power OK
Ethernet Data| Green| Flashing| Ethernet Data Transmitting & Receiving OK

Caution
Supply external power to use this transmitter as a PoE Switch Hub.

CABLE PIN Configuration TIA/EIA 568B Type

Connection Diagrams

In case of using as a 4CH PoE HUB

In case of using with EoC(Ethernet over Coax.) device (SC-IPR07P)

In case of using 8CH transmission configuration

• You may need to change the adapter depending on the camera power consumption.
• Please configure general communication network (Internet/In-company, house) separated to CCTV network.
• Please be noted that if the bandwidth exceeds 10Mbps after setting the switch to 10Mbps, a problem may occur with the video.

Recommended PoE Camera Power Consumption
PoE Camera Power Consumption Table Based on DC Adapter 48V 1.0A / 56V 1.16A

PoE Camera Power Consumption (Max. Power Output)

Adapter| PoE Camera #1| PoE Camera #2| PoE Camera #3| PoE Camera #4
DC 56V| 14W| 14W| 14W| 14W
DC 48V| 10W| 10W| 10W| 10W

• Values in the above table may vary depending on the type of camera and cable.
• Valued in the above table may be changed when using PoE switch HUB.
• When connecting a camera with large power consumption or inrush current, please use a 56V adapter or apply PoE+ to the product.
• When using the PoE function of the transmitter, transmission distance may vary depending on the camera type. Especially for cameras with high power consumption such as IP PTZ cameras or IP cameras with many IR LEDs, please use the additional adapter for camera power.

Troubleshooting Method

•    Check if the exclusive adapter is used.

•    Check the PoE switch hub connection state.

•    Check the CABLE PIN configuration state.

Video is not displayed.| •    Check the CABLE PIN configuration state.

•    Check the cable transmission distance.

•    Check the ground state.

•    Check if the camera model is able to input PoE.

•    Check if the camera is compatible with NVR.

Video status is uneven.| •    Check the CABLE PIN configuration state.

•    Check the cable transmission distance.

•    Check the ground state of the product.

•    Check the setting of camera.

(Transmission video quality, frame rate, resolution, etc.)

•    Check if the bandwidth is over 10Mbps after setting Bandwidth Switch as 10M.

Network connection state is abnormal.| •    Check the NETWORK CABLE configuration.

•    Check if there is any equipment that generates radio or strong waves in the surrounding environment.

•    Check if the Network configuration is installed properly.

Specifications

CAM SIDE

Transmission Distance (Max.)

| In 100Mbps : 100m (CAT.5e)

In 10Mbps : 250m (CAT.5e)

RX SIDE

Transmission Distance (Max.)

| 500m (RG-6)

Connection Port

| NVR PORT| RJ-45 1Port (TIA/EIA568B Type)
CAMERA PORT| 1×4 RJ-45 1Port (TIA/EIA568B Type)
EoC PORT| BNC-F 1Port , 75ohm
POWER| DC JACK 2.0pi
RJ-45 Connector

Pin Assignment(Polarity)

| 1Pin: TX(+), PWR(+)       2Pin: TX(-), PWR(+)
3Pin: RX(+), PWR(-)       6Pin: RX(-), PWR(-)
Bandwidth Switch| Change CAM Side Transmission Speed (100Mbps , 10Mbps)
Transmission Bandwidth| 10/100Mbps (Full duplex)
Temperature / Humidity| -10°C ~ +50°C / 0 ~ 80%
Case Material / Weight| Aluminum / 290g
Dimensions (mm)| 159(W) x 92.5(H) x 34.7(D)mm

• Using the LAN cable extension gender (coupler) causes signal attenuation. The use of multiple gender connections is not recommended.
• Cable transmission distance may vary depending on the specifications of camera and NVR.
• When using the camera PoE function, the transmission distance may vary depending on the type of camera.

Warranty Certificate

This product has passed thorough quality control and test, and if this gets broken during normal use, we provide the two-year warranty service.

Model No.|
---|---
Serial No.|
Distributor|
Date you purchased|
Place you purchased|
Warranty Period| Two (2) year from the date of purchase
Purchaser| Name|
Address|

• Please check this warranty indication first.
• Please contact your distributor after checking out any defects in the products.
• The standard for repair, replacement, or reimbursement follows the Customer.
• Warranty content any defect under normal use within the warranty service period we give you free repair service according to the warranty certificate.
• We charge you the fee for parts and service despite of free warranty service period. Any breakage made without care such as:
  • Breakdown due to natural disasters (lightning, fire, flood, tsunami, etc.)
  • When disassembled or repaired by the user
  • When connecting power other than rated power.
  • When you want to reassemble for a full system or replace parts within the warranty service period.
  • When an unauthorized person modified or made damage the product trying to repair it.
  • Failure due to careless handling of the user
  • When replacing consumables
  • Thunder stroke.
• Please note that we don’t support breakage after the warranty service period expired. If the customer wants to get it repaired, we charge them the fee.
• The specification is subject to change without prior notice for quality improvement.

SeeEyes Co., Ltd

50 3 ~50 9, 511~512, Sunil Technopia, 555 Dunchon daero, Jungwon gu,

Seongnam City, Gyeonggi Province, Korea (Zip Code:
TEL: +82 –(0)31 730 58 33
FAX: +82 –(0)31 777 3512
EMAIL: overseas@sscctv.com.
http://www.sscctv.com/eng.

References

• SeeEyes
• SeeEyes

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>