SeeEyes SC-IPH3002DC PoE Extender and Down Converter User Manual

Precaution and Safety Guidelines

The content of this guideline is to protect the safety of users and prevent property damage.
Please be sure to read this user’s manual thoroughly and use the device correctly.

Warning: (If you do not keep any of the below guidelines, you may get seriously injured or cause somebody’s death.)

• Be sure to install the product after unplugging power cord. Also, do not use many power plugs at the same time.

  • It may cause abnormal heat, fire and electric shock.

• Do not leave the device at any place that water falls or splashes. Also, do not put anything full of water such as a flower vase on the device.

  • It may cause malfunction or fire if liquid goes into the device

• Do not open the lid arbitrarily as this device has high voltage part inside. Never disassemble, repair or modify it.

  • By abnormal working, it may cause fire, electric shock and personal injury.

• Do not install this product in places with high humidity, dust, or soot.

  • It may cause electric shock and fire.

• Always keep the location of the appliance clean during or after installation to prevent dust.
  Especially when cleaning the device, wipe it with dry towel and do not use water, thinner or organic solvent.

  • It may cause damage to the surface of the device, malfunction or electric shock.

• Keep the device in a cool place where doesn’t let direct sunlight. Keep it at a proper temperature and avoid heating appliances like candle or heater.
  Also, keep the equipment or tools away from places where people come and go.

  • It may cause fire.

• Pay attention to possible hazards in the workplace, such as wet floor, ungrounded power extension cables, old power cords and a lack of safety earth.
  Consult your place of purchase or professional if problems arise.

  • It may cause fire and electric shock.

• Concerning the input voltage for operating this device, a voltage range must be within 10% of rated voltage.
  Also, do not use a heat source such as a hair dryer, iron and refrigerator to the same power unit.

  • It may cause abnormal heat, fire and electric shock.

• Disconnect the power plug with care during thunder and lightning.

• Do not bend the power cord by excessive force. Make sure the power cord is not crushed by heavy things.

  • It may cause fire.

• Install the cable as “U” shape in order to prevent rain water/dew/fog, etc. from falling through the cable.

Caution: (If you do not keep any of the below guidelines, you may get injured or suffer property loss.

• Avoid installing near strong magnetic fields or radio waves and wireless devices such as radio or TV.

  • Install in a place that is free from magnetic, radio, or excessive vibration.

• Proper ambient temperature and humidity are recommended.

  • Avoid extremely high temperatures(over 50°C) or low(below -10°C), and humid conditions.

• Do not place heavy items on the product or let foreign substances enter inside the device.

  • It may cause failure.

• Install in well ventilated place, and avoid direct sunlight or heat appliance.

• Strong shock or vibration may cause device failure. Be careful when using the device.

  • Install in a place without severe vibration.

• If you notice any unusual noise or smell, unplug the power supply immediately and contact the place of purchase or service center.

  • There may be a risk of fire and electric shock.

• Rotate the air properly in the system operating room and secure the cover of the main body.

  • It may be the cause of failure by environmental factors.

• Refer the device to the service center and get regular checkup to maintain the performance of the system.

  • We are not responsible for any damages caused by user’s carelessness.

• Be sure to plug the power cord with grounded outlet.

  • There is a risk of electrical shock and personal injury.

• Place the power plug in a location that is easy to operate.

  • If a failure of the product occurred, the power plug must be unplugged to power down completely.
    The power button on the main body does not completely disconnect power.

• Do not use this device in close proximity to a device that produces strong waves such as radio set(TRANCEIVER, Walkie-talkie, etc.) or repeater.
  It may affect HD-SDI and EX-SDI signal, or cause disorders such as noise or crack on the screen.

• The transmission medium(CABLE) must be a UTP(CAT.5e) cable.

• Be careful not to change the cable configuration during installation. (Refer to ‘4. CABLE PIN Configuration’ on page 5.)

• This product’s CAMERA PORT has a maximum output power of 30W and the EXTENSION PORT has a maximum output power of 30W.
  Please check the output power of each port when connecting a camera or more than two product in series.

  • The supply power is limited by the camera’s power consumption, transmission distance and cable loop resistance, and may affect other channels.

• UTP(Unshielded Twisted Pair) Cable is for indoor use only. Use a STP(Shield Twisted Pair) Cable which is covered for outdoor use.

• Transmission distance may vary depending on the type of UTP cable.

• Refer to the user’s manual for problems or questions besides the above.
  Contact our service center if you need assistance from a professional technician.

Introduction

Overview
SC-IPH3002DC is an all-in-one product that combines PoE injector/extender/splitter functions and can be used in various network construction environments.
In addition, the Ethernet data transmission distance can be extended by using the Ethernet bandwidth adjustment switch of the product, and it is a suitable product to save construction costs by supplying power to peripheral devices using DC power input using the PoE splitter function.

Features

• Support Ethernet injector function

• Ethernet extender function support

• PoE splitter function supported (DC 12V Max. 1A Output)

• Transmission distance can be extended by changing the bandwidth switch setting value (100Mbps/10Mbps).
  100Mbps switch setting: transmission possible up to 100m (based on CAT.5e)
  10Mbps switch setting: transmission possible up to 250m (based on CAT.5e)

• Power input method: DC 48~56V Adapter or PoE (DC Adapter power supply priority)

• Auto MDI/MDIX function support

• Built-in surge protection circuit

Components

SC-IPH3002DC| User’s Manual| Adapter(DC 48V, 1.0A), (Optional)
---|---|---
| ****|

The accessories included in the package may be changed.

Product Parts & Functions

1. DC12V Output : DC 12V power output terminal (Max. 1.0A)
   • When connecting the power output cable, pay attention to the polarity.
2. Camera Port LED : Camera Port Link LED, PoE Output Status LED
   < LED status indication >
    | LED Color| Status| Description
   ---|---|---|---
   Camera Port| Yellow| On/Off| On for PoE output
   Green| Off/Blink| Camera Port Data Link 시
3. Camera Port: RJ-45 connector for IP Camera connection
   • End span PoE function (Mode A) supported. (IEEE802.3 AF/AT)
4. NVR Port: RJ-45 connector for NVR or PoE Switch HUB connection
   • PoE Mode A, B support. (IEEE802.3 at type-2)
5. NVR Port LED: NVR Port Link LED, PoE Input Status LED
   < LED status indication >
    | LED Color| Status| Description
   ---|---|---|---
   NVR Port| Yellow| On/Off| On for PoE input
   Green| Off/Blink| NVR Port Data Link 시
6. Slide Switch: Slide switch for bandwidth setting
7. DC IN 48V ~ 56V: DC adapter 48V to 56V power input terminal

When the PoE power supplied to the NVR PORT is insufficient, connect an external adapter to use it

CABLE PIN arrangement (TIA / EIA 568B method)

White

|

Orange

| TX+
2|

Orange

|

Orange

| TX-
3| Green + White| White| Green| RX+
4|

Blue

|

Blue

| PWR+
5| Blue + White| White| Blue| PWR+
6|

Green

|

Green

| RX-
7| Brown + White| White| Brown| PWR-
8|

Brown

|

Brown

| PWR-

Connection Diagrams

IPH3002DC application case 1 (when using LED signage to notify CCTV installation)

IPH3002DC application case 2 (when configuring an emergency call system)

IPH3002DC application case 3 (when configuring a wireless bridge system)

• Additional power supply may be required depending on camera power consumption.
• Please design a separate network for general communication (Internet/in-house, etc.) and CCTV network.

IPH3002DC Power available by distance

• PoE camera recommended power consumption table may change depending on camera and cable type
• Power consumption table may change depending on PoE switch hub performance
• When connecting a camera with high consumption current or high inrush current, use a DC 56V adapter or apply PoE+ power to the product.
• When using as a simple switch hub, it can be used after external power is applied.
• If you cross cables between the Camera PORT and NVR PORT terminals, power may not be supplied and video may not be output

Troubleshooting method

• **** Check the power cable connection state.
• Check if the exclusive adapter is used.
• Check the PoE switch hub connection state.
• Check the CABLE PIN configuration state.
• Check if the connection to EXTENSION PORT and NVR PORT are correct.

Video is not displayed.|

• Check the CABLE PIN configuration state.
• Check the cable transmission distance.
• Check the ground state.
• Check if the camera model is able to input PoE.
• Check if the camera is compatible with NVR.
• Check if the connection to EXTENSION PORT and NVR PORT are correct.

Video status is uneven.|

• Check the CABLE PIN configuration state.

• Check the cable transmission distance.

• Check the ground state of the product.

• Check the set value of camera.
  (Transmission video quality, frame rate, resolution, etc.)

• Check if the bandwidth is over 10Mbps after setting Bandwidth Switch as 10M.

Network connection state is abnormal.|

• Check the NETWORK CABLE configuration.
• Check if there is any equipment that generates radio or strong waves in the surrounding environment.
• Check if the Network configuration is installed properly.

Specifications

Power Input

| DC Power| DC 48V 또는 DC 56V Adaptor
PoE Power| PoE IEEE 802.3af / 802.3at, Endspan / Midspan (Mode A / Mode B)
Feature| Power input DC Adaptor and DC Adapter power supply priority

among PoE

PoE Output| CAMERA PORT| Max 30W, Standard PoE Support, IEEE802.3 af/at Mode A
Power Consumption| Max 1W (No-load Condition)
Max. Transmission Distance| When setting 100Mbps: Max. based on CAT.5e. 100m
When setting 10Mbps: Max. 250m
Connection Port| NVR PORT| RJ-45 1Port (TIA/EIA568B Type)
CAMERA PORT| RJ-45 1Port (TIA/EIA568B Type)
POWER| DC JACK
RJ-45 Connector
Pin Assignment(Polarity)| 1Pin: TX(+), PWR(+)       2Pin: TX(-), PWR(+)
3Pin: RX(+), PWR(-)       6Pin: RX(-), PWR(-)

LED Indicator

| Camera Side| Yellow| On for PoE output
Green| Camera Port Data Link 시 Blink
NVR Side| Yellow| On for PoE input
Green| NVR Port Data Link 시 Blink
Slide switch| change the transmission bandwidth (100Mbps , 10Mbps)
Transmission Bandwidth| 10/100Mbps support (Full duplex)
Operating Temperature/Operating Humidity| -10°C ~ +50°C / 0 ~ 80%
Material/Weight| aluminum / 104g
Dimensions| 77(W) x 60(H) x 25(D)mm

• Using a LAN cable extension gender (coupler) causes signal attenuation.
  The use of multiple extended gender connections is not recommended.

• Cable transmission distance may vary depending on camera and NVR specifications.

• When using the camera PoE function, the transmission distance may vary depending on the camera type.

Warranty Certificate

Product No.|
---|---
Model No.|
Date of Purchase|
Place of Purchase|
Purchaser| Name|
Address & Contact No.|
Distributor| Name|
Address & Contact No.|
Warranty Period| Two(2) years from the date of purchase

Any failure that occurs in the normal use for only two years after purchase will be repaired free of charge.
Contact the phone number listed on the user’s manual for repair.
When reporting the failure, please inform the model name and condition of the product accurately.
It is convenient to know the name and department of the person in charge.
Please check this user’s manual again before reporting the failure.
Product shapes and circuits are subject to change without notice to improve performance.

Faults following will be treated as a charge:

• Failure by user’s handling without care
• Not connecting the rated power
• Disassembled or repaired arbitrarily by user
• When replacing consumables
• Failure caused by natural disaster(lightning, fire, flood, tsunami, etc.)

CUSTOMER SUPPORT

SeeEyes Co., Ltd

503~509, 511~512, Sunil Technopia, 555 Dunchon-daero, Jungwon-gu,

Seongnam City, Gyeonggi Province, Korea (Zip Code: 13215)
TEL: +82-(0)31-730-5833
FAX: +82-(0)31-777-3512
EMAIL : overseas@sscctv.com
Web: http://www.sscctv.com/eng

References

• SeeEyes
• SeeEyes

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>