SeeEyes SC-MAC02 SD or HD Analog to HDMI or CVBS Converter User Manual

June 9, 2024
SeeEyes

SeeEyes SC-MAC02 SD or HD Analog to HDMI or CVBS Converter

SC-MAC02 SD or HD Analog to HDMI or CVBS Converter

Precaution and Safety Guidelines

The content of this guideline is to protect the safety of users and prevent property damage. Be sure to read this user’s manual thoroughly and use the device correctly.

Warning (If you do not keep any of the below guidelines, you may get seriously injured or cause somebody’s death.)

  • Be sure to install the product after unplugging power cord. Also, do not use several power plugs at the same time.
    – It may cause abnormal heat, fire and electric shock.

  • Do not leave the device at any place that water falls or splashes. Also, do not put anything full of water such as a flower vase on the device.
    – It may cause malfunction or fire if liquid goes into the device.

  • Do not bend the power cord by excessive force. Make sure the power cord is not crushed by heavy things.
    – It may cause fire.

  • Do not open the lid arbitrarily as this device has high voltage part inside. Never disassemble, repair or modify it.
    – By abnormal working, it may cause fire, electric shock and personal injury.

  • Do not install this product in places with high humidity, dust, or soot.
    – It may cause electric shock and fire.

  • Do not tug at the power cord section or unplug the power plug with wet hands. If the power cord is loose, do not plug in.
    – There may be a risk of fire and electric shock.

  • Always keep the location of the appliance clean during or after installation to prevent dust. Especially when cleaning the device, wipe it with dry towel and do not use water, thinner or organic solvent.
    – It may damage the case of this device, and cause malfunction or electric shock.

  • Keep the device in a cool place where doesn’t let direct sunlight. Keep it at a proper temperature and avoid heating appliances like candle or heater. Also, keep the equipment or tools away from places where people come and go.
    – It may cause fire.

  • Pay attention to possible hazards in the workplace, such as wet floor, ungrounded power extension cables, old power cords and a lack of safety earth. Consult your place of purchase or professional if problems arise.
    – It may cause fire and electric shock.

  • Keep the back of the product more than 15cm and the sides more than 5cm from the wall. If you install the product too close to the wall, it can cause the cable to be bend, compressed too hard or break, as various external input/output ports such as power cords protrude from the back of the product.
    – It may cause fire, electric shock and personal injury.

  • Concerning the input voltage for operating this device, a voltage range must be within 10% of rated voltage, and the power outlet must be grounded. Also, do not use a heat source such as a hair dryer, iron and refrigerator to the same power unit.
    – It may cause abnormal heat, fire and electric shock.

Caution (If you do not keep any of the below guidelines, you may get injured or suffer property loss.)

  • Avoid installing near strong magnetic fields or radio waves and wireless devices such as radio or TV.
    – Install in places without any magnetics, radio waves or severe vibrations.

  • Proper ambient temperature and humidity are recommended.
    – Avoid extremely high temperatures(over 50°C) or low(below -10°C), and humid conditions.

  • Do not place heavy items on the product or let foreign substances enter inside the device.
    – It may cause failure.

  • Install in well ventilated place, and avoid direct sunlight or heat appliance. Install at a flat and stable place. Do not use an upright or slanted position.
    – It may not operate properly or might be dangerous due to the fall of the device.

  • Strong shock or vibration may cause device failure, so be careful when using the device.
    – Install in a place without severe vibration.

  • If you notice any unusual noise or smell, unplug the power supply immediately and contact the place of purchase or service center.
    – There may be a risk of fire and electric shock.

  • Circulate air properly in the system operating room and fix the cover of the main body of the product firmly.
    – It may cause failure by surrounding environment factors.

  • Refer the device to the service center and get regular checkup to maintain the performance of the system.
    – We are not responsible for any damages caused by user’s carelessness.

  • Be sure to plug the power cord with grounded outlet.
    – There is a risk of electrical shock and personal injury.

  • Place the power plug in a location that is easy to operate.
    – If a failure of the product occurred, the power plug must be unplugged to power down completely.

  • The power button on the main body of the product does not completely cut off the power.

  • The transmission medium(CABLE) must be a coaxial cable. Do not use this device in close proximity to a device that produces strong waves such as radio set(TRANCEIVER, Walkie-talkie, etc.) or repeater. It may affect the video signal, or cause disorders such as noise or crack on the screen.

  • Transmission distance may vary depending on the type of coaxial cable.

  • Disconnect the power plug with care during thunder and lightning. Refer to the user’s manual for problems or questions besides the above. Contact our service center if you need assistance from a professional technician.

  • When you extend or terminate coaxial cable, it should be connected in the following way.
    – BNC-M(Male) – BNC-JJ – BNC-M(Male): BNC Connector

  • Make the joint part of the cables insulated completely not to expose the metal parts.
    Precaution and Safety Guidelines

Introduction

Overview

SC-MAC02 is a converter which converts HD analog video input signals to HDMI & CVBS signals. The available input signals are CVI, TVI and AHD. This product is able to transmit UTC signals to camera side by connecting input video signal through Loop-Output port with DVR, recorder or other devices.

Features
  • Output of HDMI & CVBS images from SD/ HD Analog images
  • Available Loop-Output for SD/ HD Analog signals
  • Supports camera control through Loop-Output port
  • Built-in surge protection circuit

Components

SC-MAC02

| DC 12V Adapter (Optional)|

User’s Manual

---|---|---
SC-MAC02 SD or HD Analog to HDMI or CVBS Converter| |

Product Parts & Peripheral Devices Connection

Product Parts & Peripheral Devices Connection

① SD/ HD Analog Input: SD/ HD Analog signal input port
② Loop Output: Video output & UTC communication port
③ Switch Setting: Terminal Switch

Off Use Loop Output
On Not use Loop Output

④ STATE LED: In case of Power input RED On, In case of Video input GREEN On
⑤ HDMI Output: HDMI video output port
⑥ CVBS Output: CVBS video output port
⑦ DC 12V Input: DC 12V power input port

 Terminal Switch setting
  • Terminal resistance is adjustable resistance when the video out with using Loop Output port for the input video which adjust the output video status.
    In case of DVR, terminal setting status is ON, therefore when connected to DVR with using Loop Output port, you should OFF for the terminal setting.
    – The default setting is ON.

  • If you want to change the terminal setting, please use it after turning it OFF / ON.

  • Please make sure to turn the switch ON when the Loop Output is not used.

  • If Loop Output is not used, do not connect cable to the Loop Output port.

Caution: Be sure to connect only Non-PoC camera (general camera).
If PoC(Power over COAX) camera is connected, it may cause product malfunction.

Specifications

MODEL SC-MAC02
SD/ HD Analog Input 1280720p 25/30Hz, 19201080p 25/30Hz, 2560*1440p

25/30Hz,

2592x1944p 12.5/20Hz, NTSC/PAL

Loop Output Resolution| Same as Input Resolution
HDMI Output Resolution| 1920*1080p 50/60Hz
CVBS Output Resolution| NTSC, PAL
In/Output Recommended Transmission Distance| SD/ HD Analog

Input / Output

| Max. 300m / RG-59 (200m/20Ω)

Max. 600m / RG-6 (300m/12Ω)

HDMI Output| HDMI Cable 3m
CVBS| Max. 100m / RG-59 (200m/20Ω)

Max. 150m / RG-6 (300m/12Ω))

Input Power / Power Consumption| DC 12V: 0.5A, DC 12V: 150mA


Connection Port

| SD/ HD Analog Input| BNC-F 75Ω
Loop Output| BNC-F 75Ω
HDMI Output| A Type
CVBS Output| BNC-F 75Ω
Switch| Off| Use Loop Output
On| Not use Loop Output
LED| RED| In case of Power input
GREEN| In case of Video input
Temperature / Humidity| -10℃ ~ +50℃ / 0 ~ 80%
Case Body / Weight| Aluminum / 120g
Dimensions (mm)| 103(W) x 60(D) x 26.5(H)mm

  • RG-59

Total Distance

| Camera Output ~ HD Analog Input| Loop Output ~ DVR Input
---|---|---
200m| 200m|

1m

300m

| 200m| 100m

150m

|

150m

100m|

200m

200m

| 1m|

200m

  • RG-6

Total Distance| Camera Output ~ HD Analog Input| Loop Output ~ DVR Input
---|---|---

400m

| 400m| 1m
600m| 400m|

200m

300m

| 300m
200m|

400m

400m

| 1m|

400m

  • The Max. transmission distance in CVI signal is 500m (over RG-6 Coax. cable).
    ※ Total Distance
    = (Distance between Camera and HD Analog Input port) + (Distance between Loop Output port and DVR)
    ※ Distance of HD Analog Input and Loop Output are recommended to be within the total distance above.
    ※ The transmission distance may vary depending on the specifications of camera and DVR.
    ※ For AHD, TVI, CVI cameras, signal formats are not standardized, so the video may not be displayed or  UTC may not work properly depending on the manufacturer.

Connection Diagram

HDMI and CVBS Video Output Diagram (Terminal Switch ON)

Connection Diagram

Loop, HDMI and CVBS Video Output Diagram (Terminal Switch OFF)

Connection Diagram

Trouble Shooting

Symptom Identifying Method

There is no power input.

|

  • Please check the connection status of the power adapter.
  • Please check if you connected the exclusive(DC12V) adapter
  • Please check if the RED LED is On.

No HDMI image displayed.|

  • Please check if the GREEN LED is On.
  • Please check the resolution of the input signal.
  • Please check the connection status of the HDMI cable.
  • Please check the resolution of monitor if it’s supported one.
  • Please check HDMI cable’s length and capability.

No CVBS image displayed.|

  • Please check if the GREEN LED is On.
  • Please check the resolution of the input signal.
  • Please check the connection status of the BNC connectors
  • Please check the resolution of monitor if it’s supported one.
  • Please check BNC cable’s length and capability.

Video is not clear|

  • Please check the cable connection status.
  • Please check the cable length & type.
  • Please check if the camera and DVR are compatible mutually.
  • Please check whether the switch setup status is correct or not.
  • In case of Switch On, do not use Loop output
  • In case of Switch Off, use Loop output

Camera control is not available|

  • Please check if the camera and DVR are compatible mutually.

Warranty Certificate

This product has passed thorough quality control and test, and if this gets broken during normal use, we provide the two-year warranty service

Model No.|
---|---
Serial No.|
Distributor|
Date you purchased|
Place you purchased|
Warranty Period| Two (2) year from the date of purchase
Purchaser| Name|
Address|

  • Please check this warranty indication

  • Please contact your distributor after checking out any defect in the

  • The standard for repairing, replacement or reimbursement follows

  • Warranty content any defect under normal use within the warranty service period we give you free repair service according to the warranty

  • We charge you with the fee of parts and service despite of free warranty service period. Any breakage made without care such as:

    • Breakage or trouble made by natural
    • Breakage or trouble made by breaking the product guide or
    • Breakage or trouble made by wrong power voltage or
    • When you want to reassemble for full system or replace parts within warranty service
    • When unauthorized person modified or made damage on the product trying to repair it.
    • Lightening
  • Please note that we don’t support the breakage after warranty service period is
    If the customer wants to get it repaired, we charge them with the fee.

  • The specification is subject to change without prior notice for quality improvement

Customer Support

S eeEyes Co., Ltd
#503~509, 511~512, Sunil Technopia, 555 Dunchon-daero, Jungwon-gu,
Seongnam City, Gyeonggi Province, Korea (Zip Code: 13215)
TEL: +82-(0)31-730-5831/5833
FAX: +82-(0)31-777-3512
EMAIL:overseas@sscctv.com
http://www.sscctv.com/eng

Documents / Resources

| SeeEyes SC-MAC02 SD or HD Analog to HDMI or CVBS Converter [pdf] User Manual
SC-MAC02, SD or HD Analog to HDMI or CVBS Converter, SC-MAC02 SD or HD Analog to HDMI or CVBS Converter, HD Analog to HDMI or CVBS Converter, HDMI or CVBS Converter, CVBS Converter, Converter
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals