SeeEyes SC-IPE3001 IP PoE Extender

Precaution and Safety Guidelines

The content of this guideline is to protect the safety of users and prevent property damage. Please be sure to read this user’s manual thoroughly and use the device correctly.
Warning (If you do not keep any of the below guidelines, you may get
seriously injured or cause somebody’s death.)

• Be sure to install the product after unplugging power cord. Also, do not use many power plugs at the same time.

  • It may cause abnormal heat, fire and electric shock.

• Do not leave the device in a place where water will fall or splash. Also, do not place anything with water on it, such as a vase of flowers.

  •  A malfunction or fire may result if liquid gets inside the device

• Do not bend the power cord by excessive force. Make sure the power cord is not crushed by heavy things.

  • It may cause fire.

• Do not open the lid arbitrarily as this device has high voltage part inside. Never disassemble, repair or modify it.

  • Abnormal work could result in fire, electric shock, and injury.

• Do not install this product in places with high humidity, dust, or soot.

  • It may cause electric shock and fire.

• Do not tug at the power cord section or unplug the power plug with wet hands. If the power cord is loose, do not plug in.

  • There may be a risk of fire and electric shock.

• Keep the device in a cool place where doesn’t let direct sunlight. Keep it at a proper temperature and avoid heating appliances like candle or heater. Also, keep the equipment or tools away from places where people come and go.
  It may cause fire.

• Pay attention to possible hazards in the workplace, such as wet floor, ungrounded power extension cables, old power cords and a lack of safety earth. Consult your place of purchase or professional if problems arise.

  • It may cause fire and electric shock.

• Concerning the input voltage for operating this device, a voltage range must be within 10% of rated voltage. Also, do not use a heat source such as a hair dryer, iron and refrigerator to the same power unit.

  • It may cause abnormal heat, fire and electric shock.

Caution (If you do not keep any of the below guidelines, you may get injured or suffer property loss.)

• Avoid installing near strong magnetic fields or radio waves and wireless devices such as radio
  • Install in a place that is free from magnetic, radio, or excessive vibration.
• Proper ambient temperature and humidity are recommended.
  • Avoid extremely high temperatures(over 50°C) or low(below -10°C), and humid conditions.
• Do not place heavy items on the product or let foreign substances enter inside the device.
  • It may cause failure.
• Install in well ventilated place, and avoid direct sunlight or heat appliance.
• Install at a flat and stable place. Do not use an upright or slanted position.
  • It may not operate properly or might be dangerous due to the fall of the device.
• Strong shock or vibration may cause device failure. Be careful when using the device.
  • Install in a place without severe vibration.
• If you notice any unusual noise or smell, unplug the power supply immediately and contact the place of purchase or service center.
  • There may be a risk of fire and electric shock.
• Rotate the air properly in the system operating room and secure the cover of the main body.
  • It may be the cause of failure by environmental factors.
• Refer the device to the service center and get regular checkup to maintain the performance of the system.
  • We are not responsible for any damages caused by user’s carelessness.
• Be sure to plug the power cord with grounded outlet.
  • There is a risk of electrical shock and personal injury.
• Place the power plug in a location that is easy to operate.
  • If a failure of the product occurred, the power plug must be unplugged to power down completely. The power button on the main body does not completely disconnect power.
• Disconnect the power plug with care during thunder and lightning.
• Install the cable as “U” shape in order to prevent rain water/dew/fog, etc. from falling through the cable.
• UTP(Unshielded Twisted Pair) Cable is for indoor use only. Use a STP(Shield Twisted Pair) Cable which is covered for outdoor use.
  • Use standard UTP cable such as CAT.5e or above.
• Do not design and configure general network(Internet/indoor) together with CCTV network.
  • It might be the cause of problem.
• Refer to the user’s manual for problems or questions besides the above. Contact our service center if you need assistance from a professional technician.

Introduction

Overview

SC-IPE3001 is a 1-channel UTP Ethernet Data + PoE Extender. With its built-in power supply function (PoE IEEE802.3at), this product supplies power to camera over UTP 1 cable.
To compensate the short transmission distance of Network equipment (below 100m), SC-IPE3001 extends the transmission distance up to 100~250m by installing this product in the UTP cable section between camera and PoE HUB.
Also, it is able to reduce construction costs by supplying PoE to IP camera.

Features

• Transmit power + IP data over 1 UTP Cable(CAT.5e).
• TCP Rate : 100Mbps Full Duplex
• Extend Ethernet Data transmission up to 100~250m by adding 1 pc of SC-IPE3001.(Add/extend the product after checking the rated capacity of IP camera you use.)
• Auto MDI/MDIX
• Built-in surge protection circuit
• Power input: DC 48~56V Adapter or PoE (DC Adapter power priority)
• Extend transmission distance by setting bandwidth switch (100Mbps/10Mbps). 100Mbps setting : Transmit up to 100m (CAT.5e)
  10Mbps setting : Transmit up to 250m (CAT.5e)

Make sure to turn the power of the product OFF/ON after changing the setting value.

Components

| ** Power Cord, Adapter(Option)|
**

Product Parts & Functions

CAMERA SIDE : IP PoE camera connection port..

• Port to supply PoE and receive data from camera.

Green

| ON| Connected to Camera
Blinking| Successful Data Transmission
OFF| No Data Transmission

NVR SIDE : NVR or PoE Switch HUB connection port.

• Port to receive power from PoE Switch HUB / PoE Injector and supply power and data to camera.

Green

| ON| Successful LINK connection to NVR or network device
Blinking| Successful Data connection to NVR or network device
OFF| No LINK connection to NVR or network device

DC IN 48~56V : DC 48~56V input port (Able to be used as an Injector.)
Bandwidth Select Switch : Switch to select network speed (100Mbps, 10Mbps setting)

• Able to change network speed by setting the switch as 100Mbps<->10Mbps.

• Make sure to turn the power of the product OFF/ON after changing the setting value.
• The initial setting is set to 100Mbps.

Connection Diagrams

Basic Connection with Receiving Power from DC 48/56V Adapter

• Bandwidth Switch 100Mbps Setting : Transmit Max. 100m (CAT.5e)
• Bandwidth Switch 10Mbps Setting : Transmit Max. 250m (CAT.5e)

Basic Connection with Receiving Power from PoE Switching HUB

• Bandwidth Switch 100Mbps Setting : Transmit Max. 100m (CAT.5e)
• Bandwidth Switch 10Mbps Setting : Transmit Max. 250m (CAT.5e)

Multiple Connection with 2 pcs of SC-IPE3001 in 100Mbps

Multiple Connection with 2 pcs of SC-IPE3001 in 10Mbps

• Able to extend as above figure. The max. extension distance may vary depending on the rated capacity of IP camera, characteristics of the cable, and the added SC-IPE3001 quantity.
• Network Link-time may be longer as the number of Extenders is increased.
• Setting Bandwidth Switch as 100Mbps : Transmit Max. 100m (CAT.5e)
• Setting Bandwidth Switch as 10Mbps : Transmit Max. 250m (CAT.5e)
• If the bandwidth exceeds 10Mbps after setting the Bandwidth Switch to 10M, there may be a problem with the video.
• Max. Power Output in SC-IPE3001 100Mbps Setting (Using DC Adapter)

SC-IPE3001

Power Input

| SC-IPE3001

Connection Quantity

| Max. Power Output

100Mbps/100m

---|---|---

DC 48V

| 1| 38W
2| 16W
3| 9W
4| 5W

DC 56V

| 1| 48W
2| 30W
3| 18W
4| 12W

• * When using SC-IPE3001 as a PoE Injector, Max. power output is 35W (using DC 48V Adaptor).

• Max. Power Output in SC-IPE3001 100Mbps Setting (Using PoE)

SC-IPE3001

Power Input

| SC-IPE3001

Connection Quantity

| Max. Power Output

100Mbps/100m

---|---|---

PoE

| 1| 14W
2| 10W
3| 6W
4| 3W

PoE+

| 1| 25W
2| 20W
3| 14W
4| 9W

Max. Power Output in SC-IPE3001 10Mbps Setting

SC-IPE3001

Power Input

| Max. Power Output

10Mbps/250m

---|---
SC-IPE3001 x1| SC-IPE3001 x2
DC 48V| 15W| 6W
DC 56V| 28W| 13W
PoE| 7W| 3W
PoE+| 13W| 8W

• It is not recommended to use 100Mbps and 10Mbps simultaneously when connecting more than 2 SC-IPE3001.
  (In this case, the communication speed of 2 SC-IPE3001 is set to 10Mbps.)

• When connecting a camera with large power consumption or inrush current, please use a 56V adapter or apply PoE+ to the product.

CABLE PIN Configuration

Troubleshooting

• **** Check the power cable connection state.
• Check if the exclusive adapter is used.
• Check the PoE switch hub connection state.
• Check the CABLE PIN configuration state.

**No Video**|

• **** Check the CABLE PIN configuration state.
• Check the cable transmission distance.
• Check the ground state.
• Check if the camera model is able to input PoE.
• Check if the camera is compatible with NVR.

Unstable Video|

• **** Check the CABLE PIN configuration state.
• Check the cable transmission distance.
• Check the ground state of the product.
• Check the set value of camera.

(Transmission video quality, frame rate, resolution, etc.)

• Check if the bandwidth is over 10Mbps after setting Bandwidth Switch as 10M.

**Unstable Network**|

• Check the NETWORK CABLE configuration.
• Check if there is any equipment that generates radio or strong waves in the surrounding environment.
• Check if the Network configuration is installed properly.

7. Specifications

Power Input

| DC| DC 48V or DC 56V Adapter
PoE| PoE IEEE 802.3af / 802.3at, Endspan / Midspan (Mode A / Mode B)
Feature| DC Adapter power supply priority (Between DC Adapter and PoE)
PoE Output| Midspan only (Mode B)
Power Consumption| 0.5W Max.
Max. Transmission Distance| In 100Mbps : Max. 100m (CAT.5e)
In 10Mbps : Max. 250m (CAT.5e)
Transmission Bandwidth| 10/100Mbps (Full duplex)
RJ-45 Connector

Pin Assignment(Polarity)

| 1Pin: TX(+), 2Pin: TX(-), 3Pin: RX(+), 4Pin: PWR(+)
5Pin: PWR(+), 6Pin: RX(-), 7Pin: PWR(-), 8Pin: PWR(-)

LED

Indicator

| ****

CAMERA SIDE

| YELLOW ON : Power Input
YELLOW OFF : No Power Input
Green ON : Connected to Camera
Green Blinking : Normal Data Transmission
Green OFF : No Data Transmission

NVR SIDE

| YELLOW ON : Power Input
YELLOW OFF : No Power Input
Green ON : Connected to NVR
Green Blinking : Normal Data Transmission
Green OFF : No Data Transmission

Max. Power Output

| 25.5W based on IEEE802.3at Power Device

(This may vary depending on the condition of the cable and the number

of connected products.)

Bandwidth Switch| Transmission Bandwidth Settings: 100Mbps or 10Mbps

Connection Port

| CAMERA SIDE| RJ-45 1Port (TIA/EIA568B Type)
NVR SIDE| RJ-45 1Port (TIA/EIA568B Type)
POWER| DC JACK
Temperature / Humidity| -10°C~+50°C / 0 ~ 80%
Case Material / Weight| Aluminum / 64g
Dimensions (mm)| 88(W) x 42(H) x 25(D) mm

• Using the LAN cable extension gender (coupler) causes signal attenuation. The use of multiple gender connections is not recommended.
• Cable transmission distance may vary depending on the specifications of camera and NVR.
• When using the camera PoE function, the transmission distance may vary depending on the type of camera.

Warranty Certificate

This product has passed thorough quality control and test, and if this gets broken during normal use, we provide the two-year warranty service.

Model No.|
---|---
Serial No.|
Distributor|
Date you purchased|
Place you purchased|
Warranty Period| Two (2) year from the date of purchase
Purchaser| Name|
Address|

• Please check this warranty indication first.
• Please contact your distributor after checking out any defect in the products.
• The standard for repairing, replacement or reimbursement follows Customer.
• Warranty content any defect under normal use within the warranty service period we give you free repair service according to the warranty certificate.
• We charge you with the fee of parts and service despite of free warranty service period. Any breakage made without care such as:
  • Breakdown due to natural disasters (lightning, fire, flood, tsunami, etc.)
  • When disassembled or repaired by the user
  • When connecting power other than rated power.
  • When you want to reassemble for full system or replace parts within warranty service period.
  • When unauthorized person modified or made damage on the product trying to repair it.
  • Failure due to careless handling of the user
  • When replacing consumables
  • Lightning strike.
• Please note that we don’t support the breakage after warranty service period expired. If the customer wants to get it repaired, we charge them with the fee.
• The specification is subject to change without prior notice for quality improvement.

SeeEyes Co., Ltd

50 3 ~50 9 , 511~512, Sunil Technopia, 555 Dunchon daero , Jungwon g u,

S eong nam City , Gyeonggi Province , Korea (Zip Code:
TEL: +82 –(0)31 730 58 33
FAX: +82 –(0)31 777 3512
EMAIL: overseas@sscctv.com
http://www.sscctv.com /eng

References

• SeeEyes
• SeeEyes

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>