SeeEyes SC-IPU601 High Power IP Over UTP Transmission Solution User Manual

June 9, 2024
SeeEyes

SeeEyes SC-IPU601 High Power IP Over UTP Transmission Solution

SeeEyes-SC-IPU601-High-Power-IP-Over-UTP-Transmission-Solution-
product

Precaution and Safety Guidelines

The content of this guideline is to protect the safety of users and prevent property damage.
Be sure to read this user’s manual thoroughly and use the device correctly.

Warning (If you do not keep any of the below guidelines, you may get seriously injured or cause somebody’s death.)

  • Be sure to install the product after unplugging power cord. Also, do not use several power plugs at the same time.
    • It may cause abnormal heat, fire and electric shock.
  • Do not leave the device at any place that water falls or splashes. Also, do not put anything full of water such as a flower vase on the device.
    • It may cause malfunction or fire if liquid goes into the device.
  • Do not bend the power cord by excessive f orc e. Make sure the power cord is not crushed by heavy things.
    • It may cause fire.
  • Do not open the lid arbitrarily as this device has high voltage part inside. Never disassemble, repair or modify it.
    • By abnormal working, it may cause fire, electric shock and personal injury.
  • Do not install this product in places with high humidity, dust, or soot.
    • It may cause electric shock and fire.
  • Do not tug at the power cord section or unplug the power plug with wet hands. If the power cord is l oose, do not plug in.
    • There may be a risk of fire and electric shock.
  • Always keep the location of the appliance clean during or after installation to prevent dust.
  • Especially when cleaning the device, wipe it with dry towel and do not use water, thinn er or organic solvent.
    • It may damage the case of this device, and cause malfunction or electric shock.
  • Keep the device in a cool place where doesn’t let direct sunlight. Keep it at a proper temperature and avoid h eating appliances like candle or heater Also, keep the equipment or tools away from places where people come and go.
    • It may cause fire.
  • Pay attention to possible hazards in the workplace, such as wet floor, ungrounded power extension cables, old power cords and a lack of safety ear th. Consult your place of purchase or professional if problems arise.
    • It may cause fire and electric shock.
  • Concerning the input voltage for operating this device, a voltage range must be within 10% of rated voltage, and the power outlet must be groun ded. Also, do not use a heat source such as a hair dryer, iron and refrigerator to the same power unit.
    • It may cause abnormal heat, fire and electric shock

Caution (If you do not keep any of the below guidelines, you may get injured or suffer property loss.)

  • Proper ambient temperature and humidity are recommended.
    • Avoid extremely high temperatures(over 50°C) or low(below -10°C), and humid conditions.
  • Install in well ventilated place, and avoid direct sunlight or heat appliance.
  • Be sure to plug the power cord with grounded outlet.
    • There is a risk of electrical shock and personal injury.
  • Do not use this device in close proximity to a device that produces strong waves such as radio set (TRANCEIVER, Walkie talkie, etc.) or repeater. It may affect the video signal, or cause disorders such as noise or crack on the screen.
  • Disconnect the power plug with care during thunder and lightning.
  • When connecting cables, install as “U” shape in order to preve nt rainwater/dew/fog from getting into the product.
  • Refer to the user’s manual for problems or questions besides the above. Contact our service center if you need assistance from a professional technician.
  • UTP(Unshielded Twisted Pair) Cable is for in door use only. For outdoor use, it is recommended to use STP(Shield Twisted Pair) Cable which is covered with shield.
    • Use standard CAT.5e or higher UTP cable.
  • Since this product has a Po E (Power Over Ethernet .) function, it may cause malfunction to the connected device which doesn’t support Po E function. Make sure to read the user’s manual carefully before using this product.
  • Make sure to separate general communication network (internet / in house use, etc. etc.) from CCTV network.
    • It may cause malfunction.
  • Be careful not to change the network cable configuration.
    • Refer to the cable wiring way below

OVERVIEW

SeeEyes-SC-IPU601-High-Power-IP-Over-UTP-Transmission-Solution-
fig \(1\)

Network Cable Diagram

Pin No. Color Function
1 White Orange
2 Orange TX-
3 White Green
4 Blue PWR+
5 White Blue
6 Green RX-
7 White Brown
8 Brown PWR-

Introduction

Overview

The 1 channel High Power IP Over UTP Transmission Solution consists of the transmitter SC IPU601T and the receiver SC IPU601R Among SeeEyes’ IP transmission device series, this product was developed as a High Power supporting product of SC IP C 07PU, and the PoE output of the transmitter ( SC IPU601T ) supports up to 70Watt, enabling high performance an d high capacity IP cameras over long distances with PoE technology. PoE technology enables power supply to theVtransmitter and camera, so no separate power supply is required.
Existing analog UTP cameras can be replaced with IP cameras, and the existing UTP cable (CAT.5e /6 ) can be used , which shortens the construction period and reduces construction

Features

  • IEEE 802.3af/at/bt support
  • Possible to supply power for IP camera (PoE Type B supported / max. 70W)
  • Transmission bandwidth: up to 100Mbps
  • Ethernet data can be transmitted up to 800m via UTP cable (CAT.5e /6 ) (
  • Auto MDI/MDIX function support
  • Safe power transmission wit h automatic line diagnosis function
  • Camera side transmitter PoE function ON/OFF setting switch
  • Surge protection circuit

Components

SeeEyes-SC-IPU601-High-Power-IP-Over-UTP-Transmission-
Solution-fig \(3\)

Accessories included in the product are subject to change

Product Parts and Functions

SC IPU601T TransmitterSeeEyes-SC-IPU601-High-Power-IP-Over-UTP-
Transmission-Solution-fig \(4\)

  1. CAMERA PoE: Switch to set power supply to PoE IP camera.
  2. In case of connecting PoE I P camera, set CAMERA PoE switch as ON
  3. The factory setting for the PoE switch is ON.
  4. In case of connecting non PoE IP camera, set CAMERA PoE switch as OFF.
  5. LED Indicator
    Name| Color| Status
    ---|---|---
    PWR| Red| On: Power input

Off: No power input

ETH| Green| Blinking: Ethernet connected

Off: Ethernet Not connected

LINK| Green| On: Connected to Receiver

Off: Not connected to Receiver


PoE

| ****

Red

| ON: PoE Input to IP camera Off: No Poe input to IP camera

Blinking: IP camera side power supply error (short circuit,

disconnection, overcurrent)

When turning the product on, the LED turns on sequentially first and the product is operated

  1. RECEIVER SIDE : Port to connect Receiver and output video
  2. CAMERA S IDE : Port to connect IP camera

SC IPU601R ReceiverSeeEyes-SC-IPU601-High-Power-IP-Over-UTP-Transmission-
Solution-fig \(5\)

  1. NVR SIDE : Port to connect NVR or PoE Hub
  2. DC 48 5 6 V IN : Port to input DC adapter (48V or 56V) power
  3. TRANSMITTER SIDE : Port to connect Transmitter and input video
  4. LED Indicator
    Name| Color| Status
    ---|---|---
    PWR| Red| On: Power input

Off: No power input

ETH| Green| Blinking: Ethernet connected

Off: Ethernet Not connected

LINK| Green| On: Connected to Transmitter

Off: Not connected to Transmitter


PoE

| ****

Red

| On: PoE output to Transmitter

Blinking: IP camera side power supply error (short circuit,

disconnection, overcurrent)

  1. Bandwidth Select Switch 1 00Mbps, 10Mbps s etting
  2. 10M: Transmit by 10Mbps (10Mbps over CAT.5e :
  3. 100 M: Transmit by 10 0 Mbps (100Mbps over CAT.5e : 500m).
  4. When turning the product on, the LED turns on sequentially first and the product is operated

Connection Diagram

In case of connecting PoE IP Camera TX’s PoE Switch ON)SeeEyes-SC-IPU601
-High-Power-IP-Over-UTP-Transmission-Solution-fig \(6\)

Installation

  • Set SC IPU601T ’s CAMERA PoE switch to ON. (PoE LED On)

    In case of connecting non PoE camera, set transmitter’s CAMERA PoE switch to OFF.

  • Connect the IP PoE CAMERA to the transmitter and connect the UTP cable to the terminal connected to the SC IPU601R (

  • Connect UTP cable from Transmitter to Receiver C onnect Receiver to NV R or P oE Hub

  • Check the transmission distance and set t he Bandwidth switch of Receiver to the corresponding transmission bandwidth.

    • 10M: Transmit by 10Mbps 10 Mbps over CAT.5e: 800 m).
    • 100 M: Transmit by 10 0 Mbps 10 0Mbps over CAT.5e: 500 m).
  • Supply power by connecting DC Adapter (48V or 56V) to the DC Jack of the receiver. (Option)

  • Check the camera’s video from the monitor connected to NVR

    • If connected properly, LINK LED on Tx and Rx is ON and ETH LED is blinking.

Precautions for product installation

  • Use a dedicated adapter individually for each product. It is not recommended to input power to multiple products with one adapter.
  • It is not recommended if the products are in contact with each other or tied together.
  • W hen supplying PoE to the receiver it is not recommended to connect the DC adapter
  • When installing the product with PoE supply it is recommended to ground the camera after checking the video.
  • When an installing a surge protector the distance between the camera and the transmitters is recommended to be within 50m
  • Using a LAN cable extension gender (coupler) causes signal attenuation. The use of multiple extension gender connections is not recommended.

Specifications

MODEL SC-IPU601T
Power Input PoE from SC-IPU601R
Power Output Midspan PoE (Type B Only, PoE SW On/Off)
Transmission Bandwidth 10/100Mbps
Connection Port RECEIVER SIDE
CAMERA SIDE RJ-45 (TIA/EIA568B Type)

LED Indicator

| PWR| RED LED
ETH| GREEN LED
LINK| GREEN LED
PoE| RED LED
CAMERA PoE SW| Slide switch: PoE On/Off selection
Operating Temperature / Humidity| -10℃ ~ 50℃ / 0 ~ 80%
Case Body / Weight| Aluminum / 96g
Dimensions| 103(W) x 60(D) x 25(H) mm
MODEL| SC-IPU601R
---|---
Power Input| AC Adaptor(DC 48-56V) or PoE Hub (IEEE 802.3af/at/bt)
Power Output| PoE
Max. Transmission Distance

(CAT.5e)

| 100Mbps: 500m

10Mbps: 800m

Transmission Bandwidth| 10/100Mbps
Connection Port| TRANSMITTER SIDE| RJ-45 (TIA/EIA568B Type)
NVR SIDE| RJ-45 (TIA/EIA568B Type)
DC 48V-56V IN| DC-JACK


LED

Indicator

| PWR| RED LED
ETH| GREEN LED
LINK| GREEN LED
PoE| RED LED
Bandwidth Select Switch| 10M / 100M
Operating Temperature / Humidity| -10℃ ~ 50℃ / 0 ~ 80%
Case Body / Weight| Aluminum / 98g
Dimensions| 103(W) x 60(D) x 25(H) mm

Maximum supplyable power

Distance

CAT.5e

| Bandwidth| DC 56V 2A| PoE(802.3bt,

DC 54V)

| DC 48V 1A
---|---|---|---|---
50m(164ft)| 100Mbps| 70W| 52W| 41W
100m(328ft)| 100Mbps| 65W| 49W| 38W
200m(656ft)| 100Mbps| 55W| 42W| 31W
300m(984ft)| 100Mbps| 41W| 34W| 22.5W
400m(1312ft)| 100Mbps| 31W| 25.5W| 17.5W
500m(1640ft)| 100Mbps| 24.5W| 20.5W| 14W
600m(1968ft)| 10Mbps| 20.5W| 17W| 11.5W
700m(2296ft)| 10Mbps| 17.5W| 15W| 10W
800m(2624ft)| 10Mbps| 15.5W| 13W| 8.5W

  • Depending on the power specifications of the camera, a difference of about 20 to 30% may occur compared to the power supply value in the table, and the cable transmission distance may vary depending on the specifications of the camera, NVR, cable etc.
  • When using the PoE function of the transmitter, the transmission distance may vary depending on the camera type.
  • In particular, for IP PTZ cameras and cameras with many IR LEDs that consume a lot of power, use a dedicated camera power adapter. I t is recommended that the cable distance between the camera and the transmitter be less than 1 m.
  • When inputting power to the receiver through a PoE hub, it is recommended that the network cable distance be less than 1m.
  • When transmitting over a cable distance of 500m, camera input voltage may be low and may malfunction. Please , connect a DC 56V adapter to the receiver

Trouble Shooting

Symptom Checking Method


No Power

|

•    Check if PoE LED on Receiver and PWR LED on Transmitter is ON.

•    Check the connection status of UTP cable.

•    Check if the PWR LED is working properly.

•    Check the input status of power adapter or PoE Hub.

•    Check if the exclusive adapter(56V) is used.



No Video

| •    Please check if LINK LED is ON and ETH LED is flashing.

•    Check if the transmission distance is within the recommended value or not.

•    Check if the Network cable’s wire arrangement is correct.

•    In case of using PoE function on Transmitter, check if the PoE LED is On. If LED is Off, set the PoE switch as ON.



No PoE

| ****

•    Check the PoE switch status on Transmitter.

•    Check if PoE LED on Transmitter is ON.

•    Check if the Network Cable arrangement is correct.

•    Check if the IP CAMERA supports PoE function.



Unstable Network

| ****

•    Check if the Network cable’s wire arrangement is correct.

•    Check if there is Walkie-Talkie or any device which has strong waves near the product.

•    Check if the Network configuration is installed properly.



Unstable Video

| ****

•    Check the connection status of UTP and Network cable.

•    Check if the NVR is compatible with camera.

•    Check the performance status of camera.

Warranty Certificate

Product No.|
---|---
Model No.|
Date of Purchase|
Place of Purchase|


Purchaser

| Name|
Address &

Contact No.

|


Distributor

| Name|
Address &

Contact No.

|
Warranty Period| Two(2) years from the date of purchase

  • Any failure that occurs in the normal use for only two years after purchase will be repaired free of charge.
  • Contact the phone number listed on the users manual for repair.
  • When reporting the failure, please inform the model name and condition of the product accurately. It is convenient to know the name and department of the person in charge.
  • Please check this users manual again before reporting the failure.
  • Product shapes and circuits are subject to change without notice to improve performance.

Fau
lts following will be treated as a charge:

  • Failure by user s handling without care
  • Not connecting the rated power
  • Disassembled or repaired arbitrarily by user
  • Replacing consumables
  • Failure caused by natural disaster (lightning, fire, flood, tsunami, etc.)

SeeEyes Co., Ltd
5F , Sunil Technopia, 555 Dunchon daero, Jungwon gu, Seongnam City, Gyeonggi Province, Korea (Zip Code: 13215)
TEL : +82(0)31 730 5833
FAX : +82 (0)31 777 3512
EMAIL: global@sscctv.com
http://www.sscctv.com/eng

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals