REELCRAFT T-1460-0 Safe T Reel Welding Cable Reels Instruction Manual
- June 9, 2024
- REELCRAFT
Table of Contents
REELCRAFT T-1460-0 Safe T Reel Welding Cable Reels
Dimensions
| T-1460-0
---|---
A| 19”
B| 18”
C| 6”
D| 6”
E| 6 1/2”
F| 16 1/4”
Four 1/2” diameter mounting holes
| T-2464-0
---|---
A| 38”
B| 18”
C| 6”
D| 6 1/2”
E| 16 1/4”
Four 1/2” diameter mounting holes
| T-2462-0
---|---
A| 19”
B| 18”
C| 6”
D| 6 1/2”
E| 29”
Four 1/2” diameter mounting holes
IMPORTANT
Read this manual carefully before installing, operating or servicing this
equipment.
SAFETY
Injury and/or equipment damage may result if proper safety precautions are not observed.
- Ensure that only a qualified electrician installs/services this equipment.
- Ensure that power supply voltage does not exceed maximum voltage rating of reel.
- Ensure that reel is properly installed before connecting to power supply.
- Ensure that all electrical power is removed from reel before servicing.
- Check for frayed/broken wires before each use.
- Pull electrical cord from reel by grasping the electrical cord itself, not the work device.
- If an electrical malfunction should occur, remove power from reel immediately.
- Ensure that reel, electrical cable, and equipment being serviced are properly grounded. Use an ohmmeter to check ground continuity.
- If reel ceases to unwind or rewind, remove power immediately. Do not pull or jerk on electrical cable!
- Treat and respect the cable reel as any other piece of machinery, observing all common safety practices.
WARNING: Even low voltage can cause irreparable damage or death! Exercise
extreme caution while operating or servicing this equipment.
Reel craft Industries, Inc.
2842 E Business Hwy 30, Columbia City, IN 46725 Ph:
800-444-3134 /
260-248-8188
Fax: 800-444-4587 /
260-248-2605
Customer Service: 855-634-9109
reelcraft@reelcraft.com
www.reelcraft.com
INSTALLATION INSTRUCTIONS
Inspection
Unpack and inspect reel for damage. Turn the reel by hand to check for smooth
operation. Check for completeness.
Mounting
Note: Ensure that only a qualified electrician installs/services this equipment.
- Four 1/2” diameter mounting holes are located at the base of the reel. Mount reel using four (customer supplied) bolts; tightening them securely to ensure a solid, rigid attachment.
Electrical
Note: Observe any applicable NEC, OSHA, and local electrical codes when
installing this equipment.
- Attach a cable lug (customer supplied) to the end of the outlet cable.
- Mount lug to collector ring assembly using one 1/2-13 UNC bolt.
Item #| Description| # Req| T-1460-0| # Req|
T-2462-0| T-2464-0
---|---|---|---|---|---|---
1| Self Tapping Screw| 12| S285-14| 26| S285-14| S285-14
2| Spool Cover| 1| 261517| 2| 261517| 261517
3| Hex Cap Screw| 5| S2-85| 10| S2-85| S2-85
4| Spool Half| 1| 261546| 2| 261546| 261546
5| Hose Clamp| 1| 261541-1| 2| 261541-1| 261541-1
6| Spool Half| 1| 261547| 2| 261547| 261547
7| Spool Cover| 1| 261518| 2| 261518| 261518
8| Shaft Key| 1| 261516| 2| None| 261516
9| Hex Jam Nut| 1| 261575| 2| None| 261575
10| Set Screw| —| None| 4| S34-184| None
11| Handle Post| 1| 261515| 2| 261515| 261515
12| Handle| 1| 261514| 2| 261514| 261514
13| Hex Jam Nut| 2| S77-108| 4| S77-108| S77-108
14| Collector Ring Assembly| 1| S600791| 2| S600791| S600791
15| Tensioning Nut| 1| 261548| 2| 261548| 261548
16| Hub Assembly| 1| S600752| 2| S600752| S600752
17| Main Shaft| 1| 261545| 2| 261562| 261545
18| Base Assembly| 1| 600746| 1| 600744| 600745
19| Cord Grip Assembly| 1| 261555| 2| 261555| 261555
20| Lock Washer| 1| S115-816| 2| S115-816| S115-816
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>