REELCRAFT Series 7000 Spring Driven Hose Reels Instruction Manual
- October 30, 2023
- REELCRAFT
Table of Contents
REELCRAFT Series 7000 Spring Driven Hose Reels
Dimensions
| | 1| 2
---|---|---|---
in mm| in mm
A| 20 1/4 514| 20 1/4 514
B| 19 3/4 502| 19 3/4 502
C| 7 13/16 198| 7 13/16 198
D| 3 7/8 98| 3 7/8 98
E| 7 178| 8 1/4 210
IMPORTANT
Read this manual carefully before installing, operating or servicing this equipment.
SAFETY
Personal injury and/or equipment damage may result if proper safety precautions are not observed.
- Ensure that reel is properly installed before connecting input and output hoses.
- Bleed fluid/gas pressure from system before servicing reel.
- Before connecting reel to supply line, ensure that pressure does not exceed maximum working pressure rating of reel.
- Remember, even low pressure is very dangerous and can cause personal injury or death.
- Be aware of machinery and personnel in work area.
- If a leak occurs in the hose or reel, remove system pressure immediately.
- A high tension spring assembly is contained within the reel. Exercise extreme caution.
- Pull hose from reel by grasping the hose itself, not the control valve.
- Ensure that reel, hose, and equipment being serviced are properly grounded. Use an ohmmeter to check ground continuity.
- If reel ceases to unwind or rewind, remove system pressure immediately. Do not pull or jerk on hose!
- Treat and respect the hose reel as any other piece of machinery, observing all common safety practices.
INSTALLATION INSTRUCTIONS
MOUNTING
Caution: Unless reel was specified differently when ordering, maximum installation height is 16 feet. Do not exceed this distance.
- Unpack and inspect reel for damage. Turn by hand to check for smooth operation. Check for completeness.
- Configure reel for top, side or bottom-wind hose dispensing by removing nuts (1) securing guide arm bracket (2). Position guide arm bracket to desired location, and replace nuts. Caution: When changing guide arm positions, the U-bolt must be placed in the proper location as instructed in figure A below. The reel can “latch out” during use if this instruction is not adhered to.
- Position reel on floor, wall, or ceiling. Secure into place using four (customer supplied) bolts (3).
INSTALLING THE INPUT HOSE(S)
Warning : Ensure that supply line pressure does not exceed maximum
working pressure rating of reel. Apply pipe thread sealant to all threads.
Caution : Use flexible hose connection at input. Do not use rigid
plumbing.
- Connect supply line hose (4) to main shaft input (5) as indicated in illustration.
INSTALLING THE OUTPUT HOSE(S)
Warning : Use extreme caution; reel under tension. Avoid releasing latch mechanism. Apply pipe thread sealant to all threads.
- Manually turn sheave (10) until spring is tight, back off 3 turns, then latch.
- Route output hose(s) (11) through guide arm bracket (2), U-bolts (12), then through cutout (13) in spool as indicated in illustration.
- Connect output hose(s) (11) to swivel (14) as indicated in illustration.
- Tighten U-bolts (12).
- Charge hose(s). Momentarily open control valve to purge hose(s) of gases. When fluid appears at control valve, close valve. With hose(s) fully charged, release latch and wind output hose(s) onto reel.
ADJUSTMENTS
Warning : Use extreme caution; reel under tension. Avoid releasing latch mechanism. If necessary, adjust spring tension on reel by adding or removing wraps of hose from spool, one wrap at a time, until desired tension is obtained. Add wraps to increase tension. Remove wraps to decrease tension.
SERVICE INSTRUCTIONS
User servicing of the reel is limited to replacing input/output hoses only.
Refer all other repairs to an authorized service person or directly to
Reelcraft. Failure to do so can result in personal injury and/or equipment
damage and may void the warranty.
Warning : Rewind hose on reel, then bleed pressure from system before
performing the following procedures.
-
Replace hoses in accordance with procedures given in “Installation Instructions” section of this manual.
Caution : When replacing drive spring, hold the center of the spring down as the hub is pulled out. If the center is allowed to raise up, the spring may escape from it’s container with enough force to cause injuries.
When disposing of old or broken spring assemblies, the coils should be welded or wired together to prevent possible injury to scrap handling personnel. -
All mating moving parts are to be lubricated with Perma Bond or Loctite anti-seize compound.
Parts Description
**Prior to August 2016
See online tech bulletin for more information
Item # | # Req. | Description | Part Number |
---|---|---|---|
4 | 1 | Sheave Assembly | S260011 |
6 | 1 | Spring Arbor Assembly | S600621 |
7 | 1 | Gasket | S260069 |
8 | 1 | Spring Case Assembly | S260074 |
12 | 1 | Base Assembly | S600016 |
13 | 1 | 1/2-13 Set Screw | S35-84 |
14 | 1 | Guide arm with Rollers | S600017 |
16 | 4 | 5/16-18 Locknut | 300107 |
17 | 7 | 10-32 x 3/8” Nyloc Nut | S82-15 |
18 | 1 | 1/2-20 x 5/8” Hex Nut | S280-8 |
19 | 1 | Latch Spring | S260067 |
21 | 1 | 10-32 Shoulder Screw | S393-2 |
22 | 1 | Latch Pawl Assembly | S600018 |
23 | 1 | 3/8-24 Jam Nut | S76-106 |
24 | 1 | Spring Case Stud | 260031 |
25 | 1 | U-bolt | 3-117440 |
26 | 2 | 1/4-20 x 3/8” Locknut | S261650-1 |
Item # | Description | # Req. | 7600 OLB |
--- | --- | --- | --- |
1 | Swivel Assembly** | 1 | 600093-1B |
1 | Swivel Assembly | 1 | 602791-1B |
2 | Swivel | 1 | 602681-2 |
3 | 90° Ell | 1 | S160-3 |
5 | Drive Spring Assembly | 1 | S260028 |
10 | Main Shaft** | 1 | 261046-B |
10 | Main Shaft | 1 | S602754-B |
11 | 1 1/4” Snap Ring | 1 | 300007 (x2) |
Max. Operating Pressure | 500 PSI | 500 PSI | |
Max. Operating Temperature | 210 °F | 210 °F | |
Dimension Size Index | 1 | 1 |
Item # | # Req. | Description | Part Number |
---|---|---|---|
2 | 1 | Spool & Hub Assembly | 602704 |
3 | 1 | Arbor Key | 261275 |
4 | 1 | Spring Arbor | 261274 |
7 | 5 | Snap Ring | 300007 |
10 | 1 | Guide Arm & Roller Assembly | 602697 |
11 | 4 | Lock Nut | 300107 |
12 | 1 | Set Screw | S35-84 |
13 | 1 | Base Assembly | 602686 |
14 | 1 | Latch Pawl Assembly | S602694 |
15 | 6 | Nyloc Nut | S82-15 |
16 | 1 | U-Bolt | 3-117440 |
17 | 2 | 1/4-20 Nylon Locknut | 261650-1 |
Item # | Description | # |
Req.
| HD76005 OLB
---|---|---|---
1| Swivel & Ell Assembly| 1| 602791-2
5| Drive Spring Assembly| 1| S6002718-80
6| Main Shaft| 1| 263200
Max. Operating Pressure| 500 PSI
Max. Operating Temperature| 210 °F
Dimension Size Index| 2
Customer Support
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Customer Service: 855-634-9109 •
reelcraft@reelcraft.com •
www.reelcraft.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>