KLEER EK24FCK 24 inch FHD Computer Monitor User Manual
- June 13, 2024
- KLEER
Table of Contents
User Manual
24 inch: EK24FCK
27 inch: EK27FC65
LED monitor
Part 1 Monitor controls and usage.
Product Contents
The contents of the product are as follows:
- Instruction manual
- Monitor
- Power adapter
- Screw
- Type
- cable
- Monitor base
Base Assembly
Before Assembly and Use
For a comfortable user experience and viewing of the monitor, consider the
following factors when positioning and adjusting the monitor.
Viewing Distance: The recommended viewing distance between the eyes and
the monitor screen is approximately 1.5x of the screen size.
To meet this requirement in a small office, keep your desk away from the wall
or partition. to make room for your display.
Monitor Height: Place your head and neck in a natural and comfortable
[vertical or horizontal] position when placing the monitor. If the monitors
height cannot be adjusted, you can achieve the desired height by placing a
book or other sturdy product under the monitor base. A general rule of thumb
is to make the top of the screen of the monitor match the line of your view
[or slightly lower] from a comfortable seating position. However, in a
situation where the eye muscles are relaxed, it is recommended to optimize the
height of the monitor so that the relative position between the eye and the
central position of the monitor provides an appropriate visual distance and a
comfortable viewing experience for the user.
Inclination: By adjusting the display s inclination position, you can
optimize the contents of your screen content to keep your head and neck in
optimal posture.
General Position: When locating the display, make sure that overhead
lights or nearby windows do not glare or reflect on the screen.
Monitor Image Control
This section describes the controls required to adjust the monitor image.
Using the On
Screen Display OSD, Display controls.
User controls can be viewed through the OSD to adjust settings.
How to use:
- Press the Menu key to open the OSD main menu.
- Use or [arrow keys] to move between icons. Select the icon and press the Menu Key to access the required function. If there is a sub menu, you can use or [arrow keys] to move between options and then press the Menu key to select a function. Adjust with or [arrow keys], then press the Menu key to save.
- Press the Auto key to cycle through the sub menu and exit the OSD.
- Lock the OSD by pressing and holding the Menu key for ten seconds. This will prevent the OSD from being adjusted accidentally. To unlock the OSD, hold the Menu key for 10 seconds.
- DDC/CI is disabled by default. Using the OSD Exit key, press, and hold Auto for ten seconds to disable/enable it.
Use direct access control.
If the On Screen Display OSD is not displayed, you can use the direct access
control.
Item| Icon| Details| Use| Default| Selection
Range| | Note
---|---|---|---|---|---|---|---
Luminance| | brightness| Brightness control| 90| 0-100| |
contrast| Contrast control| 50| 0-100| |
DCR (dynamic contrast ratio)| DCR control| OFF| ON/OFF| |
overdrive| OD on/off| OFF| ON/OFF| | Only applicable models are supported
Color Control| | color temperature| Color temperature control| Warm|
Customizable| |
R(red)| | 0-100| | |
G(green)| | 0-100| | |
B(blue)| | 0-100| | |
Low Blue light| | Off/low/ medium/Strong| Customizable| |
View Mode| | | | ECO mode| Standard| |
Volume| | Mute| Speaker mute| OFF| ON/OFF| | Only Applicable to speaker
supported products
Volume| Speaker Volume control| 50| 0-100|
Image Setup| | horizontal position| horizontal position control| | | | For
this model only
Vertical position| Vertical Position Control| | |
Clock| | | |
Phase| | | |
OSD Setup| | Language| Select language| Korean| Korean/English| |
Vertical position| OSD Vertical Position control| 50| 0-100| |
horizontal position| OSD horizontal position control| 50| 0-100| |
| | duration| OSD display time setting| 5| 5-120| |
Transparency| OSD transparency| 25| 0/25/50/75/100| |
Other Functions| | Input selection| Input signal selection| Input signal
selection| Type-C, HDMI, Audio| |
Aspect Ratio| Aspect Ratio Adjustment| Wide (16:9)| 16:9/4:3| |
Free sync| | OFF| | | Only applicable models are supported
Information| | | | | | |
reset| Factory reset| | | |
Manual image settings.
Manual image settings.
If automatic image setup does not provide the image you want, you can perform
a manual image setup. [Only for VGA Analog ] NOTE: Turn on the monitor and
wait approximately 15 minutes.
Press the Menu key to open the OSD menu.
Access by pressing the Menu key with or [arrow keys].
Use or [arrow keys] to select Manual and press the Menu key to access.
Use or [arrow keys] to Select Clock or Phase adjustment.
Clock: [Pixel Frequency] Adjusts the number of pixels that can be scanned in a
horizontal scan. If the frequency is not correct, vertical bars may appear on
the screen and the picture width is incorrect.
Phase: Adjusts the phase of the pixel clock signal. Incorrect phase adjustment
can cause.
horizontal perturbation in bright images. When the image no longer appears to
be distorted, Press Enter to save the Clock and Phase adjustments.
Press the Auto key to exit the OSD menu.
Supported Screen Modes
Supported Screen Modes
Supported resolutions | Vertical Frequency[Hz] |
---|---|
640×480 | 60Hz |
640×480 | 72Hz |
640×480 | 75Hz |
720×400 | 70Hz |
80 x600 | 60Hz |
80 x600 | 72Hz |
80 x600 | 75Hz |
1024×768 | 60Hz |
1024×768 | 70Hz |
1024×768 | 75Hz |
1152×864 | 75Hz |
1280×1024 | 60Hz |
1280×1024 | 70Hz |
1280×1024 | 75Hz |
140×900 | 60Hz |
1680×1050 | 60Hz |
1920×1080 | 60Hz |
Part 2 Reference Information
Monitor Specifications
24 inch model: EK24FCK
Classification | 60.4cm TFT LCD with WLED Back Light |
---|---|
Maximum resolution | 1920 x 1080 (pixels) |
Pixel pitch | 0.2745mm (horizontal) x 0.2745mm (vertical) |
Viewing angle | 178° / 178° (HN) |
luminance | 300 cd/m2 (Typical) |
Contrast ratio | 1,000:1 (Typical) |
Response speed | 14ms (Typical) |
Input signal | Type-C x 1, HDMI Input x 1, Audio Output x 1, USB-A(2.0)x2 |
Connector | Type-C, HDMI, Audio |
Screen size | 527.04mm (H) x 296.46 (V) |
Power Consumption | 28.5W (Max) |
Size (WxHxD) | 528.8mm x 404.1mm x 134.3mm |
Weight | 2.95kg |
Weight (Including Package) | 4.69kg |
Operating temperature | 0°C – 40°C |
Storage temperature | -20°C – 60°C |
27 inch model: EK27FC65
Classification | 68.5cm TFT LCD with WLED Back Light |
---|---|
Maximum resolution | 1920 x 1080 (pixels) |
Pixel pitch | 0.3114mm (horizontal) x 0.3114mm (vertical) |
Viewing angle | 178° / 178° (HN) |
luminance | 300 cd/m2 (Typical) |
Contrast ratio | 1,000:1 (Typical) |
Response speed | 14ms (Typical) |
Input signal | Type C x 1, HDMI Input x 1, Audio Output x 1, USB A(2.0)x2 |
Connector | Type C, HDMI, Audio |
Screen size | 597.88mm (H) x 336.31 (V) |
Power Consumption | 108W (Max) |
Size (WxHxD) | 538.8mm x 404.1mm x 134.3mm |
Weight | 4.0kg |
Weight (Including Package) | 6.3kg |
Operating temperature | 0°C – 40°C |
Storage temperature | 20°C 60°C |
Connecting the Monitor
Mobile phone laptop connection via Type C port
The device must support Android 10 desktop mode to use it smoothly. Not
compatible with iPhone.
Computer connection via HDMI cable HDMI cable not included in product contents
Connecting an external speaker through the Audio out terminal
External accessory connection via USB port
It is also possible to mount an external monitor arm using the VESA hole.
Monitor arm is not provided separately.
Power Management info.
The power management feature is activated when the computer detects that the
mouse or keyboard has not been used for a user defined interval. There are
several states of power management described in the following table.
Chart 2-3. Power LED
State| Power LED| Screen| Recovery operation|
Consistency
---|---|---|---|---
On (open)| Green| normal| |
Standby/ Pause| Orange| empty| If you move your mouse, there may be a slight
delay before the image is displayed again.
Note: If there is no image output on the monitor, it will go into standby
mode.|
Off (close)| Off (close)| empty| Pressing the power button may cause a slight
delay before the image is displayed again|
Troubleshooting 1
If you have any problems setting up or using your monitor, you can
troubleshoot it yourself.
Before contacting customer service, please try the recommended actions below,
depending on the problem you are experiencing.
Chart 3-2. Troubleshooting
Problem | Possible Cause | Recommended action | Note |
---|---|---|---|
Indicators (The input signal is out of range) Power light blinks green | |||
“Monitor is not supported in system settings.” display mode | If you are |
replacing an old monitor, reconnect it and then the display mode will be
adjusted to the specified range supported by the new monitor.
If you are using a Windows system, restart the system in secure mode and then
select a supported display mode for your computer| Choose a supported display
mode for your page
Troubleshooting 2
If you have any problems setting up or using your monitor, you can
troubleshoot it yourself. Before contacting customer service, please try the
recommended actions below, depending on the problem you are experiencing.
Chart 3-2. Troubleshooting
Problem | Possible Cause | Recommended action | Note |
---|---|---|---|
Image quality is poor | The video signal cable is not well connected to the | ||
monitor or system | Make sure the signal cables are securely connected to the | ||
system and to the monitor. | |||
Color settings may be incorrect | Select a different color setting from the OSD | ||
menu | Refer to page 3 Monitor image control | ||
The automatic image setting function was not performed | Perform automatic | ||
image setup | Refer to page 3 Monitor image control |
The power light does not come on.
Image is not displayed.| The monitors power switch is not turned on. Adapter
connector cable is loose.
There is no power supply from the outlet.| Check that the power cord is
properly connected. Make sure the outlet has power.
Power on the monitor. Disconnect and reconnect the adapter. Replace the power
outlet.|
The screen is blank, and power is applied. The LED is displayed in orange.|
Display is in standby/suspend mode| Press any key on the keyboard or move the
mouse to resume work.
Check your computer’s power options settings.| Refer to page 9 Power
Management info.
Power LED is green but no image available| Video cable is loose or
disconnected from system or monitor.| Make sure the video cable is securely
connected to the system|
The display settings have either the lowest brightness or contrast.| Adjust
the Brightness and Contrast settings in the OSD menu| Refer to page 3 Monitor
image control
Troubleshooting 3
If you have any problems setting up or using your monitor, you can
troubleshoot it yourself. Before contacting customer service, please try the
recommended actions below, depending on the problem you are experiencing.
One or more pixels are discolored.| This is an inherent characteristic of LCD
technology and is not an LCD defect.| If more than 5 pixels are missing,
please contact support| Refer to page 11 Customer Support
---|---|---|---
Lines in text are blurred or images are blurred| The display properties
settings for systems with unoptimized image settings are not optimized.|
Adjust the system resolution setting of 1920×1080, 60Hz.
according to the resolution of this monitor.| Refer to page 3 Monitor image
control
Perform automatic image setup. If automatic image setup does not work, perform
manual image setup| Refer to page 6 Available Display Modes
If you are using your own resolution, the system will adjust Dots Per Inch
(dpi).
(DPI, dots per inch) setting could be improved further.| See the advanced
section of system display properties.
Part 3 Customer Support
Service Center 82 1877 2884
If you have any questions, please contact the service center
Note] Trademarks other than EKLEER Co, Ltd.
are the trademarks of the respective trademark holders.
Business name: EKLEER Co, Ltd.
Product name: LED Monitor
Service center: 82] 1877 2884
Equipment name/model number: LED Monitor/EK24FCK
Equipment name/model number: LED Monitor/EK27FC65
Manufacturer/country of manufacture: EKLEER Co, Ltd, All Rights Reserved/
China Distributor: I3I distribution Co, Ltd.
Date of manufacture: Separately indicated.
Reported application number: R-R-eKL -EK24FCK
Reported application number: R-R-eKL -EK27FC65
Labeling according to the Electrical Appliances and Household Appliances
Safety Management Act