JBL Bar 1000 Powered 7.1.4 Channel Sound Bar System Owner’s Manual

BAR 1000

OWNER’S MANUAL

IMPORTANT SAFETY INSTRUCTIONS

Verify Line Voltage Before Use
The JBL Bar 1000 (soundbar, detachable speakers and subwoofer) has been designed for use with 100-240 volt, 50/60 Hz AC current. Connection to a line voltage other than that for which your product is intended can create a safety and fire hazard and may damage the unit. If you have any questions about the voltage requirements for your specific model or about the line voltage in your area, contact your retailer or customer service representative before plugging the unit into a wall outlet.
Do Not Use Extension Cords
To avoid safety hazards, use only the power cord supplied with your unit. We do not recommend that extension cords be used with this product. As with all electrical devices, do not run power cords under rugs or carpets, or place heavy objects on them. Damaged power cords should be replaced immediately by an authorized service center with a cord that meets factory specifications.
Handle the AC Power Cord Gently
When disconnecting the power cord from an AC outlet, always pull the plug; never pull the cord. If you do not intend to use this speaker for any considerable length of time, disconnect the plug from the AC outlet.
Do Not Open the Cabinet
There are no user-serviceable components inside this product. Opening the cabinet may present a shock hazard, and any modification to the product will void your warranty. If water accidentally falls inside the unit, disconnect it from the AC power source immediately, and consult an authorized service center.

INTRODUCTION

Thank you for purchasing the JBL Bar 1000 (soundbar, detachable speakers and subwoofer) which is designed to bring an extraordinary 3D sound experience to your home
entertainment system. We encourage you to take a few minutes to read through this manual, which describes the product and includes step-by-step instructions for setting up and getting started.
To make the most of product features and support, you may need to update the product software through the Internet or the USB connector in the future. Refer to the  oftware update section in this manual to ensure that your product has the latest software.
Designs and specifications are subject to change without notice.
If you have any questions about the soundbar, installation or operation, please contact your retailer or customer service representative, or visit our website: www.jbl.com.

JBL One app
With the JBL One app, you can

• easily complete product setup;
• connect *music streaming services;
• discover new music with integrated music services;
• use one button to access your preset playlist and speaker settings;
• access software updates when they are available.

For more information, see “5.3 Connection with your home network” and “7.5 Play through the JBL One app”.
NOTES:
– *Subscription may be needed and not provided by the JBL One app.

WHAT’S IN THE BOX

Unpack the box carefully and ensure that the following parts are included. If any part is damaged or missing, do not use it and contact your retailer or customer service representative.

PRODUCT OVERVIEW

3.1 Soundbar
3.1.1 Controls

1) (Source)

• Switch on
• Select a sound source: TV (default, for audio input from TV connection where the HDMI OUT (TV ARC/ TV eARC) connector is prioritized over the OPTICAL connector), Bluetooth or HDMI IN

2) (Volume)

• Switch on
• Decrease or increase the volume
• Press and hold to decrease or increase the volume continuously
• Press the two buttons together to mute or unmute

3) Status indicator

System:

| Regular flashing (white)| System startup
| Fast flashing (white)| Software updating in progress
| Solid (amber)| Restoring factory settings
Network connection:
| Slow breathing (white)| Entering Wi-Fi setup mode, or network disconnected
| Solid (green)| Soundbar discovered by the JBL One app
| Solid (white)| Network connected
| Solid (yellow)| Weak Wi-Fi connection

4) Microphone
• For sound calibration
5) Status display
3.1.2 Rear connectors

1. POWER
   • Connect to power (with the supplied power cord)

2. USB
   • USB connector for software update
   • Connect to a USB storage device for MP3 file playback (for US version only)

3. ETHERNET
   • Connect to your home network through an Ethernet cable

4. HDMI IN (1/ 2/ 3)
   • Connect to the HDMI output on your digital device

5. TV connectors

HDMI OUT (TV ARC/ TV eARC)

• Connect to the HDMI ARC / HDMI eARC input on your TV OPTICAL
• Connect to the optical output on your TV or digital device

3.2 Detachable speakers 1) Type C USB connector

• For battery charging

2) (Power)

• Press to switch on
•  Press and hold for more than 3 seconds to switch off

3) Status indicator

• For battery power

| Flashing (red)| Low battery
---|---|---
| Solid (red)| Battery charging in progress

For wireless connection status

| Slow flashing (white)| Disconnected from the soundbar
---|---|---
| Fast flashing (white)| Connecting to the soundbar

0

| Solid (white)| Connected to the soundbar

3.3 Subwoofer Connection status indicator

0

| Solid (white)| Connected to the soundbar
---|---|---
| Fast flashing (white)| Pairing mode
| Slow flashing (white)| Reconnecting or exiting the pairing mode
| Solid (amber)| Standby mode

2) Power connector
• Connect to power (with the supplied power cord)
3.4 Remote control

1. ---

   • Switch on or to standby

2.  Source selectors
   TV
   • Select the TV source (default, for audio input from TV connection where the HDMI OUT (TV ARC/ TV eARC) connector is prioritized over the OPTICAL connector)
   (Bluetooth)
   • Select the Bluetooth source
   • Press and hold to connect a Bluetooth device
   HDMI
   • Repeatedly press to switch between the HDMI IN sources: HDMI 1 (default)/ 2/ 3

3.  Sound effect buttons

• Select the level of Dolby Atmos/DTS:X effect: middle (default), high or low

• Select the bass level for subwoofer: 1/2/3 (default)/4/5
(available when both of the detachable rear speakersare undocked from the soundbar)
• Select the surround sound level for rear speakers: middle(default), high, muted or low

4. CALIBR
   • Press to start sound calibration

5. (Moment)
   • Press to directly access the playlist or speaker settings
   that you have personalized in the JBL One app

6. (Playback controls during the music streaming over JBL One app, Chromecast built-in™, AirPlay, Alexa or Bluetooth)
   • Single press: Pause or resume playback
   • Double press: Next track
   • Triple press: Previous track

7. +/-
   • Increase or decrease the volume
   • Press and hold to increase or decrease the volume continuously

8. (Mute)
   • Mute/unmute

3.4.1 App-enabled control
With the JBL One app on your Android and iOS device, you can do the following:

• Wi-Fi setup;
• Audio calibration & demo;
• Personalize audio settings;
• Manage and control device;
• Music service integration;
• Additional features.

PLACE

4.1 Desktop placement
Place the soundbar, detachable speakers and subwoofer on a flat and stable surface. Refer to the recommended distance in the following diagram. NOTES:
– The power cord shall be properly connected to power.
– Do not place any objects on the top of the soundbar, detachable speakers or subwoofer.
– Charge the detachable speakers in time to ensure sufficient battery power (See “6.2 Charge the detachable speakers”).
– Use the supplied side caps to cover the two ends of the soundbar after you detach the rear surround speakers (See Step 5 under “4.2.2 Wall-mount the detachable speakers as rear surround speakers”).
4.2 Wall-mounting
Wall-mount the soundbar and detachable rear speakers together or separately.
4.2.1 Wall-mount the soundbar

1. Preparation:
   a) With the distance of about 2” (50mm) from your TV, stick the supplied wall- mounting template to a wall by using adhesive tapes.
   b) Use your ballpen tip to mark the screw holder location. Remove the template.
   c) On the marked location, drill a 4 mm/0.16” hole.

2. Install the support for wall-mounting bracket.

3. With the screw, fasten the wall-mounting bracket onto the bottom of the soundbar.

4. Mount the soundbar.

5. After the soundbar is securely wall-mounted, dock the two detachable speakers onto the soundbar.

NOTES:
– Make sure that the wall can support the weight of the soundbar.
– Install on a vertical wall only.
– Avoid a location under high temperature or humidity.
– Before wall-mounting, make sure that cables can be properly connected between the soundbar and external devices.
– Before wall-mounting, make sure that the soundbar is unplugged from power. Otherwise, it may cause an electric shock.
– To move the soundbar, first remove the two detachable speakers to avoid accidental damage.
– Use the supplied side caps to cover the two ends of the soundbar after you detach the rear surround speakers (See Step 5 under “4.2.2 Wall-mount the detachable speakers as rear surround speakers”).
4.2.2 Wall-mount the detachable speakers as rear surround speakers

1. From the soundbar, remove the two detachable speakers.
2. Install the wall-mounting bracket.
3. Fasten the support onto the back of the speakers.
4. Mount the speakers.
5. Install the side caps as needed.

CONNECT

5.1 Connection with your TV and digital devices
For audio playback through the soundbar, connect the soundbar with your TV through the supplied HDMI cable or an optical cable (sold separately).
An HDMI connection supports digital audio and video with a single connection. HDMI connectivity is the best option for your soundbar.
5.1.1 TV (HDMI ARC / eARC)
(Recommended connection for the best Dolby Atmos / DTS:X experience)

1. Connect the soundbar with the HDMI IN (ARC / eARC) connector on your TV by using the supplied HDMI cable.
   • On your TV, check that HDMI-CEC and HDMI ARC / eARC have been enabled. Refer to the owner’s manual of your TV for more information.

2. Use an HDMI cable (V2.0 or later) to connect the soundbar with your digital device, such as a set-top box, DVD/Blu-ray player or game console.
   • On your digital device, check that HDMI-CEC has been enabled. Refer to the owner’s manual of your digital device for more information.
   • On your digital device, select “Bitstream” or “Raw data” in the audio output settings for the best Dolby Atmos experience.

3. To play audio from the digital device connected to the soundbar, repeatedly press HDMI on the remote control to select the HDMI source.

NOTES:
– If your TV does not support HDMI eARC, make sure that you connect your digital device through the HDMI IN connector on the soundbar instead of your TV. Otherwise, the Dolby Atmos information cannot pass through the HDMI (ARC) connectors from the TV to the soundbar.
5.1.2 TV (HDMI eARC )

1. Connect the soundbar with the HDMI IN (eARC) connector on your TV by using the supplied HDMI cable.
   • On your TV, check that HDMI-CEC and HDMI ARC / eARC have been enabled. Refer to the owner’s manual of your TV for more information.

2. Use an HDMI cable (eARC compatible, V2.0 or later) to connect your TV with your digital device, such as a streaming device, set-top box, DVD/Blu-ray player or game console.
   • On your digital device, check that HDMI-CEC has been enabled. Refer to the owner’s manual of your digital device for more information.
   • On your TV and digital device, select “Bitstream” or “Raw data” in the audio output settings for the best Dolby Atmos experience.

3. To play audio from the digital device connected to your TV, select TV on the remote control.

5.1.3 OPTICAL NOTES:
– With the 4 up-firing speakers and the detachable surround speaker design, the Dolby surround upmixer of the soundbar can expand the legacy channel-based audio of Dolby Digital format, including 5.1 and 7.1 content, and provide an immersive 3D Atmos experience.

1. Connect the soundbar with your TV by using an optical cable.
2. Use an HDMI cable (V2.0 or later) to connect your TV with your digital device, such as a streaming device, set-top box, DVD/Blu-ray player or game console.
3. To play audio through the optical cable, select TV on the remote control.

NOTES:
– * The HDMI cable (for digital device connection) and the optical cable are sold separately.
– Full compatibility with all HDMI-CEC devices is not guaranteed.
– When both HDMI ARC and optical cables are connected to the soundbar for audio input from TV connection, the HDMI ARC connection is prioritized.
5.2 Bluetooth connection
Through Bluetooth, connect the soundbar with your Bluetooth device, such as a smartphone, tablet and laptop.
5.2.1 Connect a Bluetooth device
1. To select Bluetooth source, press on the soundbar or on the remote control.
→ “BT PAIRING”: Ready for BT pairing
2. On your Bluetooth device, enable Bluetooth and search for “JBL Bar 1000_xxxx” within three minutes.
→ Successful connection: The device name is displayed if your device is named in English. A confirmation tone is heard.
5.2.2 To reconnect the last paired device
Your Bluetooth device is retained as a paired device when the soundbar goes to standby mode. Next time you switch to the Bluetooth source, the soundbar reconnects the last paired device automatically.
5.2.3 To connect to another Bluetooth device
1. In the Bluetooth source, press and hold on the soundbar or on the remote control until “BT PAIRING” is displayed.
→ The soundbar enters the Bluetooth pairing mode.
2. Follow the Step 2 under “5.2.1 Connect a Bluetooth device”.
• If the device has ever been paired with the soundbar, first unpair “JBL Bar 1000_xxxx” on the device.
NOTES:
– The Bluetooth connection will be lost if the distance between the soundbar and Bluetooth device exceeds 33 ft (10 m).
– Electronic devices may cause radio interference. Devices that generate electromagnetic waves must be kept away from the soundbar, such as microwaves and wireless LAN devices.
5.3 Connection with your home network
Through Wi-Fi or an Ethernet cable, connect the soundbar to your home network. With the JBL One app and the supported streaming services (Chromecast built- in, AirPlay and Alexa), the soundbar allows you to stream audio on smartphones or tablets through the soundbar speakers.

1. On the soundbar, enter the Wi-Fi setup mode:
   • Press any button to switch on (See “7.1 Power-on/Auto standby/Auto wakeup”).
   → If the soundbar has not been connected to a network, the screen shows “HELLO” and then, “SETUP WIFI”.
   • To re-enter the Wi-Fi setup mode, press and hold and until “SETUP WIFI” is displayed.

2. On your Android or iOS device, add the soundbar to your home Wi-Fi network through the JBL One app.
   a) Connect your Android or iOS device to your home Wi-Fi network. Download the JBL One app.
   b) Follow the app instructions to complete setup.

3. If necessary, use an Ethernet cable to connect the soundbar to your home network.
   • Make sure that you connect to the same network as you did during the setup.

NOTES:
− On your Android or iOS device, you can name the soundbar in the JBL One app.
− On your iOS device, add the soundbar to the Apple Home app and manage it together with other AirPlay 2-compatible speakers.
− On your iOS device, if the soundbar has been added to your home Wi-Fi network, you can start AirPlay streaming from an AirPlaycompatible app (See “7.7 Play through
AirPlay”).
− Availability of online music streaming services varies by country.
− Some features require subscriptions or services not available in all countries.

SETUP

6.1 Connect the detachable rear speakers and subwoofer

1. Connect the soundbar to power by using the supplied power cord.
   → The screen on the soundbar shows “LOAD” and then, “HELLO”.

2. Do the following to start the connection:
   • Connect the subwoofer to power by using the supplied power cords;
   • Dock the detachable speakers onto the soundbar, or press on the detachable speakers to fast re-connect to the soundbar.
   → The soundbar connects the subwoofer automatically.
   Connected: turns solid white on the subwoofer.
   → The soundbar connects the detachable speakers automatically.
   Connected: The status indicator turns solid white (0) on the detachable speakers.

NOTES:
– Use the supplied power cords only.
– Before connecting to power, make sure that you have completed all other connections ( See “5.1 Connection with your TV and digital devices” ).
6.2 Charge the detachable speakers
When the detachable surround speakers are out of battery, their wireless connection with the soundbar will be lost.
The first time you use the two detachable speakers, charge them for more than 3 hours to ensure sufficient battery power.
→ When the battery power runs low, the status indicator flashes red on the detachable surround speakers and “REAR SPKR
LOW BATT” is displayed on the soundbar.
→  When the battery power runs out, “DOCK REAR SPKR” is displayed on the soundbar. 6.2.1 Charge by docking the detachable speakers
Charging starts when you dock the detachable speakers onto the soundbar.
→  When the soundbar switches to standby mode, turns on; turns off when the detachable speakers are fully charged.
→  It takes about 3.5 hours for the empty battery to be fully charged. 6.2.2 Charge through a USB cable
• Use a USB-C cable to connect the detachable speakers to power respectively.
• For the detachable speakers, the status indicator is used for status indication of both battery power and wireless connection (See “3.2 Detachable speakers”).
NOTES:
– * The USB-C cable is sold separately.
6.3 3D surround sound
6.3.1 Sound calibration
Optimize your 3D surround sound experience for your unique listening environment.
For sound calibration, do the following:

• Make sure that your room is quiet;
• Make sure that the soundbar and the two detachable rear speakers are fully in sight of each other, without obstacles in between.
• Make sure that the left and right rear speakers are properly placed, the L speaker on the left and the R speaker on the right.

1. Calibrate the listening zone

1. Place the detachable rear speakers beside your seating position.
   • Make sure that the two detachable speakers have been connected to the soundbar (See “6.1 Connect the detachable rear speakers and subwoofer”).

2. On the remote control, press CALIBR to start calibration.
   → “1-CALIBRATION” is displayed on the soundbar.

3. When “PRESS AGAIN TO CONFIRM” is displayed, press CALIBR again.
   →  Countdown starts from 5 to 1.
   →  Calibration tone is heard. Audio calibration starts.
   “CALIBRATING”: Calibration in progress
   “1-DONE”: Calibration of the listening zone is completed successfully.

2) Calibrate the speaker position

1. Place the detachable rear speakers in your desired location.
2. On the remote control, press CALIBR.
   → “2-CALIBRATION” is displayed on the soundbar.
   →  Countdown starts from 5 to 1.
   → Calibration tone is heard. Audio calibration starts.
   “CALIBRATING”: Calibration in progress
   “2-DONE”: Calibration of the speaker position is completed successfully.

NOTES:
– During sound calibration, all buttons on the remote control are disabled except for and CALIBR.
6.3.2 Dolby Atmos® / DTS:X®
With Dolby Atmos or DTS:X, overhead audio distribution is provided for powerful 3D sound immersion.

1. To play the surround sound of Dolby Atmos or DTS:X, connect and play your Blu-ray player or streaming device as described under “5.1 Connection with your TV and digital devices”.
2. To select suitable strength for Dolby Atmos or DTS:X, press on remote control to toggle between middle (default), high, or low.

NOTES:
– The Atmos or DTS:X sound effects are respectively available in Dolby or DTS:X audio content only.
6.3.3 Rear adjustment
With both of the detachable rear speakers undocked, you can select the surround sound level.

1. Check that the soundbar and the detachable rear speakers are connected wirelessly (See “6.1 Connect the detachable rear speakers and subwoofer”).
2. On the remote control, press to toggle between surround sound levels.
→ “MID” / “HIGH” / “MUTE” / “LOW” is displayed (Default: “MID”).
→ “UNDOCK REAR SPKR” is displayed if the detachable rear speakers have been docked onto the soundbar.![JBL Bar 1000 Powered 7.1.4 Channel Sound Bar System

• Fig 26](https://manuals.plus/wp-content/uploads/2023/03/JBL- Bar-1000-Powered-7.1.4-Channel-Sound-Bar-System-Fig-26.png) 6.3.4 Bass adjustment
  You can make bass adjustment as needed.• On the remote control, press to toggle between bass levels.
  →  “LVL1” to “LVL5” is displayed (Default: “LVL3”).

PLAY

7.1 Power-on/Auto standby/Auto wakeup 7.1.1 Switch on
• To switch on, press any button on the soundbar, or on the remote control.
→“HELLO” is displayed.
→  The subwoofer is reconnected to the soundbar automatically. Connected: turns solid white.
→ The detachable speakers are reconnected to the soundbar automatically. Connected: The status indicator turns solid white (O)
7.1.2 Auto standby
If the soundbar is inactive for more than 10 minutes, it will switch to standby mode automatically. “STDBY” is displayed.
→  The subwoofer also goes to standby, and turns solid amber.
→ The detachable speakers switch to standby, and the status indicator turns off for wireless connection status.
→ Next time you switch on the soundbar, it returns to the last selected source.
NOTES:
– On the detachable speakers, press and hold for more than 3 seconds to switch off; press again to reconnect to the soundbar.
7.1.3 Auto wakeup
In standby mode, the soundbar will wake up automatically when

• the soundbar is connected to your TV through the HDMI ARC connection and your TV is switched on;
• the soundbar is connected to your TV through the HDMI ARC connection and through the HDMI connection, is also connected to your digital device such as a set-top box, DVD/ Blu-ray player or game console, and your digital device is switched on;
• the soundbar is connected to your home network and audio is streamed to the soundbar through the music streaming services over JBL One app, Chromecast built-in, AirPlay or Alexa.

7.2 Play from the TV source
With the soundbar connected, you can enjoy TV audio from the soundbar speakers.

1. Make sure that your TV is set to support external speakers and the built-in TV speakers are muted. Refer to the owner’s manual of your TV for more information.
2. Make sure that the soundbar has been properly connected to your TV (See “5.1 Connection with your TV and digital devices”).
3. To select the TV source, press on the soundbar or TV on the remote control.
   → “TV”: The TV source is selected.
   • In the factory settings, the TV source is selected by default.

NOTES:
– If the soundbar is connected to your TV through both an HDMI cable and an optical cable, the HDMI cable source is selected for the TV connection.
7.2.1 TV remote control setup
To use your TV remote control for both your TV and the soundbar, check that your TV supports HDMI-CEC. If your TV does not support HDMI-CEC, follow the steps under “TV remote control IR learning”.
HDMI-CEC
If your TV supports HDMI-CEC, enable the functions as instructed in your TV user manual. You can control the volume +/-, mute/ unmute, and power on/standby functions on your soundbar through the TV remote control.
TV remote control IR learning
Through IR learning, your Infra-red TV remote control can learn some commands of the soundbar.
1. On the soundbar, press and hold and until “LEARNING” is displayed.
→ You enter the TV remote control learning mode.
2. Point your TV remote control at the soundbar. Follow the screen instructions to operate the buttons on your TV remote control:
• When any one of “POWER”, “VOL+”, “VOL-”, or “MUTE” is displayed on the soundbar, press the desired button on your TV remote control.
→  “DONE”: The functions of the soundbar button are learnt by your TV remote control buttons.
→  The soundbar returns to the last selected source.
• To stop and exit the TV remote control learning mode, press and hold and on the soundbar until “EXIT LEARNING” is displayed.
→  The learnt functions are discarded.
NOTES:
– The soundbar will exit the TV remote control learning mode automatically if no action is taken for 30 seconds. The learnt functions are discarded.
7.3 Play from the HDMI IN source
With the soundbar connected as shown, your digital device can play video on your TV and audio from the soundbar speakers.

1. Make sure that the soundbar has been properly connected to your TV and digital device (See “5.1 Connection with your TV and digital devices”).

2. Switch on your digital device.
   → Your TV and the soundbar wake up from standby mode and switch to the input source automatically.
   • To select the HDMI IN source on the soundbar, toggle on the soundbar or HDMI on the remote control.

3. Switch your TV to standby mode.
   → The soundbar and source device are switched to standby mode.

NOTES:
– Full compatibility with all HDMI-CEC devices is not guaranteed.
7.4 Play from the Bluetooth source
Through Bluetooth, stream audio play on your Bluetooth device to the soundbar.

1. Check that the soundbar has been properly connected to your Bluetooth device (See “5.2 Bluetooth connection”).

2. To select the Bluetooth source, press on the soundbar or on the remote control.

3. Start audio play on your Bluetooth device.
   • Alternatively, press on the remote control to control playback.

4. Adjust the volume on the soundbar, remote control or your Bluetooth device.

7.5 Play through the JBL One app
Through the JBL One app, stream audio from online music services to the soundbar.

1. On the soundbar,
   • Check that the soundbar has been properly connected to your home network (See “5.3 Connection with your home network”).

2. On your Android or iOS device,
   a) Check that your Android or iOS device has been connected to the same network as the soundbar.
   b) Launch the JBL One app, browse available *music streaming services to select music, and then, start music streaming to the connected soundbar.
   • Use the search box to discover music with the integrated music library of available music services.![JBL Bar 1000 Powered 7.1.4 Channel Sound Bar System

• Fig 32](https://manuals.plus/wp-content/uploads/2023/03/JBL- Bar-1000-Powered-7.1.4-Channel-Sound-Bar-System-Fig-32.png)

  3. To exit from the music playback, switch to other sources.

NOTES:
– *Subscription may be needed and not provided by the JBL One app.
Access your presets with the (Moment) button
By pressing on the remote control, you can access the playlist and speaker settings that you have personalized on the JBL One
app.
1. On the JBL One app,
personalize the (Moment) feature.2. On the soundbar,
• Press on the remote control to access the personalized playlist and speaker settings.

7.6 Play through Chromecast built-in
Through Chromecast built-in, stream audio on your Android or iOS device to the soundbar.

1. On the soundbar,
   • Check that the soundbar has been properly connected to your home network (See “5.3 Connection with your home network”).

2. On your Android or iOS device,
   a) Check that your Android or iOS device has been connected to the same network as the soundbar.
   b) Launch the JBL One app, and check that you have enabled the streaming service of Chromecast built-in. c) On a Chromecast- enabled app, play music, tap the cast icon and select the connected soundbar.

3. To exit from the music playback, switch to other sources.

7.7 Play through AirPlay
Through AirPlay, stream audio on your iOS device to the soundbar.

1. On the soundbar,
   • Check that the soundbar has been properly connected to your home network (See “5.3 Connection with your home network”).

2. On your iOS device,
   a) Check that your iOS device has been connected to the same network as the soundbar.
   b) To enter the Control Center on an iOS device, swipe down from the upper right corner. Tap to select the connected soundbar and then, start audio streaming from an app.

3. To exit from the music playback, switch to other sources.

7.8 Play through Amazon Music
With the soundbar connected to Alexa, you can stream music from the Amazon Music library to the soundbar.

1. Check that the soundbar has been properly connected to your home network (See “5.3 Connection with your home network”).

2. On your Android or iOS device,
   a) Check that your Android or iOS device has been connected to the same network as the soundbar.
   b) Launch the JBL One app, and check that you have enabled the streaming service of Amazon Alexa.
   

3. Launch the Amazon Alexa app to start music playback.• Open the Amazon Music app to access the Amazon Music library.
   • Make sure that you start music playback from the same Alexa account that you have enabled in the JBL One app. Refer to the Amazon Alexa app for more details.

NOTES:
– The soundbar can support audio streaming and cannot support video streaming.
– During playback through Chromecast built-in, AirPlay or Alexa, music playback pauses on the current connected device when you start music playback on a second connected device.
– When the soundbar switches between your home Wi-Fi and wired network during AirPlay, music playback pauses and will resume in a few minutes, depending on the bandwidth condition of broadband.
For the connection to your home wired network, see “5.3 Connection with your home network”.
7.9 Multi-room playback
With the multi-room playback, you can stream music on your Android or iOS device to multiple Chromecast-enabled/ AirPlay / Alexa speakers.

7.9.1 Chromecast built-in

1. Through the Google Home app, connect multiple Chromecast-enabled speakers to the same network, assign them to multiple rooms, and create groups as needed.
2. Run a Chromecast-enabled app on your smartphone or tablet.
3. Play music. Press and select the grouped speakers.

NOTES:
– To create a multi-room speaker group in the Google Home app, make sure that you have connected all the speakers to the same home network and have used the same Google login account. Refer to the Google Home app for more details.
– Depending on the bandwidth of your local network, you can stream music to up to 6 Chromecast-enabled speakers.
7.9.2 AirPlay

1. On an iOS device, enter the Control Center.
2. Tap to select multiple connected speakers as needed.
3. Start music streaming from an app.

7.9.3 Alexa MRM: Multi-Room Music

1. Check that you have enabled the streaming service of Amazon Alexa on the soundbar through the JBL One app.
2. Through the Amazon Alexa app, create a Multi-room Music group for the soundbar. Refer to the Amazon Alexa app for more information.
   

NOTES:
– To create a multi-room music group in the Amazon Alexa app, make sure that you have connected all the devices to the same home network and have used the same Alexa login account. Refer to the Amazon Alexa app for more details.

SOUND SETTINGS

8.1 Audio sync
With the audio sync function, you can synchronize audio andvideo to make sure that no delay is heard from your video content.

1. On the remote control, press and hold TV for more than three seconds and then, press +.
   → “SYNC” is displayed.

2. Within five seconds, press + or – on the remote control to adjust the audio delay and match with video.
   →  The audio sync timing is displayed.

8.2 Smart mode
With the smart mode enabled by default, you can enjoy TV programs with rich sound effects. For TV programs such as news and weather forecasts, you can reduce sound effects by disabling the smart mode and switching to the standard mode.
Smart mode: EQ settings and JBL Surround Sound are applied for rich sound effects.
Standard mode : The preset EQ settings are applied for standard sound effects.
To disable the smart mode, do the following :
• On the remote control, press and hold for more than three seconds and then, press .
→ You switch to another mode. “OFF SMART MODE”: The standard mode is enabled.
→ Next time you switch on the soundbar, the smart mode is enabled again automatically.
8.3 PureVoice dialogue enhancement technology
By taking advantage of the PureVoice dialogue enhancement technology, the PureVoice allows you to enhance vocal clarity and easily hear and understand speech.
By default, the PureVoice is enabled if you play movies from the TV/ HDMI IN source; and the PureVoice is disabled if you stream music over Bluetooth, Chromecast built-in, Alexa and AirPlay.
To disable or enable the PureVoice mode,
• On the remote control, press and hold for more than five seconds and then, press .
→ “ON PUREVOICE”: The PureVoice is enabled.
→ “ OFF PUREVOICE”: The PureVoice is disabled.
→  Next time you switch on the soundbar, the Purevoice is enabled again automatically.

RESTORE FACTORY SETTINGS

By restoring the default settings defined at factories, you remove all your personalized settings from the soundbar.
• On the soundbar, press and hold , + and  – for more than 5 seconds.
→  “RESET” is displayed.
→  The soundbar restarts.

SOFTWARE UPDATE

For optimal product performance and your best user experience, JBL may offer software updates for the soundbar system in the future. Please visit www.jbl.com or contact JBL call center to receive more information about downloading update files.
Updating online • Connect the soundbar to your home network. Updating online happens automatically if software updates are available.
→  “WAIT”: Software updating in progress
→  “DONE”: Software updating completed
NOTES:
– Software updates will be synchronized to the two detachable speakers when they are connected to or docked onto the soundbar.
Updating through a USB storage device

1. Check that you have saved the software update file to the root directory of a USB storage device.
   • Make sure that your USB storage device meets the following requirements:
   – Maximum capacity: 64 GB
   – File system: FAT32

2. Connect the USB device.
   →  “USB”: The soundbar switches to the USB source.

3. To enter the software update mode, press and + on the soundbar.
   →  “CHECKING UPDATE” is displayed.
   → “WAIT”: Software updating in progress
   →  “DONE”: Software updating completed

NOTES:
– Keep the soundbar powered on and the USB storage device mounted before software updating is complete.

RE-CONNECT THE SUBWOOFER

The soundbar and subwoofer are paired at factories. After power-on, they are paired and connected automatically. In some special cases, you may need to pair them again. To re-enter the subwoofer pairing mode

1. On the rear panel of subwoofer, press and hold until it turns fast flashing white.
2. To enter the subwoofer pairing mode on the soundbar, press and hold on the remote control for more than three seconds. Then, press  – on the remote control.
   → “SUB PAIRING”: The subwoofer is ready for pairing.
   → “SUB PAIRED”: The subwoofer is connected.

NOTES:
− The subwoofer will exit the pairing mode in three minutes and go to standby, if pairing is not completed. turns from fast flashing white to off. To return to the pairing mode, press .

PRODUCT SPECIFICATIONS

General specification:

• Model: BAR 1000 (soundbar unit)
  BAR 1000 SURROUND (detachable speaker)
  BAR 1000 SUB (subwoofer unit)

• Sound system: 7.1.4 channel

• Power supply: 100 – 240V AC, ~ 50/60Hz

• Total speaker power output (Max @THD 1%): 880W

• Soundbar output power (Max @THD 1%): 440W

• Surround speaker output power(Max @THD 1%): 2x 70W

• Subwoofer output power (Max. @THD 1%): 300 W

• Soundbar transducer: 5x (46×90)mm racetrack drivers, 3x 0.75” (20mm) tweeters, 2x 2.75” (70mm) up-firing fullrange drivers

• Surround speaker transducer: 0.75” (20mm) tweeter, 2.75” (70mm) up-firing full-range driver

• Subwoofer transducer: 10” (260mm)

• Networked standby power: < 2.0 W

• Operating temperature: 0°C – 45°C

• Lithium battery: 3.635V, 3283mAh

• Detachable surround speaker playtime: up to 10 Hours (may vary according to content type and volume level)

HDMI specification:

• HDMI video input: 3
• HDMI video output (with Enhanced Audio Return Channel, eARC): 1
• HDMI HDCP version: 2.3
• HDR pass through: HDR10, Dolby Vision

Audio specification:

• Frequency response: 33Hz – 20kHz (-6dB)
• Audio inputs: 1 Optical, Bluetooth, USB (USB playback is available in US version. For other versions, USB is for Service only.)

USB specification:

• USB port: Type A
• USB rating: 5V DC, 0.5A
• Supporting file formats: mp3
• MP3 codec: MPEG 1 Layer 2/3, MPEG 2 Layer 3, MPEG 2.5 Layer 3
• MP3 sampling rate: 16 – 48 kHz
• MP3 bitrate: 80 – 320 kpbs

Wireless specification:

• Bluetooth version: 5.0
• Bluetooth profile: A2DP 1.2, AVRCP 1.5
• Bluetooth transmitter frequency range: 2400 MHz – 2483.5 MHz
• Bluetooth transmitter power: <15 dBm (EIRP)
• Wi-Fi network: IEEE 802.11 a/b/g/n/ac/ax (2.4GHz/5GHz)
• 2.4G Wi-Fi transmitter frequency range: 2412 – 2472 MHz (2.4 GHz ISM Band, USA 11 Channels, Europe and others 13 Channels)
• 2.4G Wi-Fi transmitter power: <20 dBm (EIRP)
• 5G Wi-Fi transmitter frequency range: 5.15 – 5.35GHz, 5.725 – 5.825GHz
• 5G Wi-Fi transmitter power: 5.15 – 5.25GHz <23dBm, 5.25 – 5.35GHz <20dBm, 5.725 – 5.825GHz <14dBm (EIRP)
• 2.4G wireless transmitter frequency range: 2406 – 2474 MHz
• 2.4G wireless transmitter power: <10 dBm (EIRP)

Dimensions

• Total soundbar dimensions (W x H x D): 1194 x 56 x 125mm / 47” x 2.2” x 4.9”
• Main soundbar dimensions (W x H x D): 884 x 56 x 125 mm / 34.8” x 2.2” x 4.9”
• Detachable surround speaker dimensions (each) (W x H x D): 155 x 56 x 125 mm / 6.1” x 2.2” x 4.9”
• Subwoofer dimensions (W x H x D): 305 x 440.4 x 305 mm / 12” x 17.3” x 12”
• Soundbar weight: 3.72 kg / 8.2 lbs
• Detachable surround speaker weight (each): 0.7 kg / 1.55 lbs
• Subwoofer weight: 10 kg / 22 lbs
• Packaging dimensions (W x H x D): 1000 x 375 x 475 mm / 39.4” x 14.8” x 18.7”
• Packaging Weight: 19.4 kg / 42.7 lbs

TROUBLESHOOTING

Never try to repair the product yourself. If you have problems using this product, check the following points before you request services.
System
The unit will not turn on.

• Check if the power cord is plugged into power and the soundbar.

The soundbar has no response to button pressing.

• Restore the soundbar to factory settings (See “9. RESTORE FACTORY SETTINGS”).

Sound
No sound from soundbar

• Make sure that the soundbar is not muted.
• Select the correct audio input source on the remote control.
• Connect the soundbar to your TV or other devices properly
• Restore the soundbar to its factory settings by pressing and holding , + and – on the soundbar for more than 5 seconds.

Distorted sound or echo

• If you play audio from your TV through the soundbar, make sure that your TV is muted or the built-in TV speaker is disabled.
  Audio and video are not synchronized.

• Enable the audio sync function to synchronize audio and video (See “8.1 Audio sync”).

No height sound effects of Dolby Atmos

• If your TV supports HDMI ARC only, make sure that you have connected your digital device to the soundbar through the HDMI IN connector on the soundbar (See “5.1.1 TV (HDMI ARC / eARC)”)
• Enjoy the sound effects of Dolby Atmos when you play movies from the TV / HDMI source. For audio streaming over Bluetooth or casting apps (enabled by Chromecast built-in, AirPlay or Alexa), Dolby Atmos is not supported.

Bluetooth
A device cannot be connected with the soundbar.

• Check if you have enabled Bluetooth on the device.
• If the soundbar has been paired with another Bluetooth device, reset Bluetooth (see “5.2.3 To connect to another Bluetooth device”).
• If your Bluetooth device has ever been paired with the soundbar, reset Bluetooth on the soundbar, unpair the soundbar on the Bluetooth device, and then, pair the
  Bluetooth device with the soundbar again (see “5.2.3 To connect to another Bluetooth device”).

Poor audio quality from a connected Bluetooth device

• The Bluetooth reception is poor. Move the source device closer to the soundbar, or remove any obstacle between the source device and the soundbar.

The connected Bluetooth device connects and disconnects constantly.

• The Bluetooth reception is poor. Move the source device closer to the soundbar, or remove any obstacle between the source device and the soundbar.

Wi-Fi
Failed to connect to Wi-Fi.

• Make sure that Wi-Fi is turned on.
• Make sure that you have selected the right network and entered the correct password.
• Make sure that your router or modem is turned on and within the range.
• In your router settings, make sure that you have set the security type to WPA2 or auto.
• Make sure that your soundbar is connected to the same wireless LAN as your smartphone or tablet.
• If you have difficulties in setting up Wi-Fi, hold + and – on the soundbar until “SETUP WIFI” is displayed.

Playback
AirPlay cannot find the soundbar as an AirPlay speaker for music streaming.

• On your Apple device, update the software to the latest version: iOS 13.4 and later, Mac OS 10.15.4 and later, or TV OS 14.3.
• Make sure that your Apple device has been connected to the same network as the soundbar.
• For a PC running iTunes for Windows, you can stream music from your PC to the soundbar through Bluetooth. Music playback does not work smoothly when the sound source switches from Bluetooth to Chromecast built-in, AirPlay or Alexa.
• The quality of audio casting and playback are dependent on the traffic and coverage of the network that connects the soundbar and your casting devices, such as phones, tablets and PCs.

Music playback does not resume when the sound source switches from Bluetooth to TV/HDMI IN, and then back to Bluetooth.

• The music playback in the Bluetooth device stops when the sound source switches from Bluetooth to TV / HDMI IN. When you switch back to the Bluetooth source, start music playback in the Bluetooth device again.

The soundbar is in the “Offline” status in the Amazon Alexa app or issues happen to Alexa MRM-related playbac k.

• To recover the soundbar, restore the soundbar to its factory settings by pressing and holding ,+ and – for more than 5 seconds.

Remote control
The remote control does not work.

• Check if the batteries are drained. If so, replace them with new ones.
• Reduce the distance and angle between the remote control and the main unit.

Failed to complete the TV remote control learning.

• Check if you are using an infra-red TV remote control. The IR learning is not supported by a Bluetooth TV remote control.

Low power standby mode
The soundbar cannot enter the low power standby mode when it completes the power charging of detachable speakers.

• To enter the low power standby mode, press and hold on the remote control until “CEC 1” is displayed on the soundbar; then, press and hold on the remote control again until “CEC 2” is displayed.
• To exit the low power standby mode, unplug the power cord and then, plug it again.

TRADEMARKS

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by HARMAN International Industries,  Incorporated is under license. Other trademarks and trade names are those of their respective owners.
The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Wi-Fi CERTIFIED 6™ and the Wi-Fi CERTIFIED 6™ Logo are trademarks of Wi-Fi Alliance®.
Dolby, Dolby Vision, Dolby Atmos, and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation. Manufactured under license from  Dolby Laboratories. Confidential unpublished works. Copyright © 2012–2021 Dolby Laboratories. All rights reserved.
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS, Inc. DTS, DTS:X, and the DTS:X logo are registered trademarks or trademarks of DTS, Inc. in the United States and other countries. © 2021 DTS, Inc. ALL RIGHTS RESERVED.
Google, Android, Google Play and Chromecast built-in are trademarks of Google LLC. Use of the Works with Apple badge means that an accessory has been designed to work specifically with the technology identified in the badge and has been certified by the developer to meet Apple performance standards.
Apple, and AirPlay are trademarks of Apple Inc., registered in the U.S. and other countries.
To control this AirPlay 2–enabled speaker, iOS 13.4 or later is required. Amazon, Alexa, and all related marks are trademarks of Amazon.com, Inc. or its affiliates. Use your phone, tablet or computer as a remote control for Spotify. Go to spotify.com/connect to learn how.
The Spotify Software is subject to third party licenses found here: https://www.spotify.com/connect/third-party-licenses.

OPEN SOURCE LICENSE NOTICE

This product contains open source software licensed under GPL. For your convenience, the source code and relevant build instruction are also available at
https://harman- webpages.s3.amazonaws.com/JBL_BAR_Gen3_package_license_list.htm.
Please feel free to contact us at:
Harman Deutschland GmbH
HATT: Open Source, Gregor Krapf-Gunther,
Parkring 3 85748 Garching bei Munchen, Germany or OpenSourceSupport@Harman.com if you have additional question regarding the open source software in the product.

HARMAN International Industries,
Incorporated 8500 Balboa Boulevard,
Northridge, CA 91329 USA
www.jbl.com
© 2022 HARMAN International Industries, Incorporated.
All rights reserved.
JBL is a trademark of HARMAN International Industries, Incorporated, registered in the United
States and/or other countries. Features, specifications and appearance are subject to change
without notice.

QUICK START GUIDE
BAR 1000 Before using this product, read the safety sheet carefully. * Power cord quantity and plug type vary by regions. To move the soundbar, first remove the two detachable speakers to avoid accidental damage.

The soundbar will pair with the two detachable speakers and the subwoofer automatically when they are powered on. Sound Calibration
Optimize your 3D surround sound experience for your unique listening environment.

On an Android™ or iOS device, add the soundbar to your home Wi-Fi network through the JBL One app. Follow the app instructions to complete setup.

• Some features require subscriptions or services not available in all countries.

General specification:

• Model: BAR 1000 (soundbar unit)
  BAR 1000 SURROUND (detachable speaker)
  BAR 1000 SUB (subwoofer unit)

• Sound system: 7.1.4 channel

• Power supply: 100 – 240V AC, ~ 50/60Hz

• Total speaker power output (Max @THD 1%): 880W

• Soundbar output power (Max @THD 1%): 440W

• Surround speaker output power(Max @THD 1%): 2x 70W

• Subwoofer output power (Max. @THD 1%): 300W

• Soundbar transducer: 5x (46×90)mm racetrack drivers, 3x 0.75” (20mm) tweeters, 2x 2.75” (70mm) up-firing full-range drivers

• Surround speaker transducer: 0.75” (20mm) tweeter, 2.75” (70mm) up-firing full-range driver

• Subwoofer transducer: 10” (260mm)

• Networked standby power: < 2.0 W

• Operating temperature: 0 °C – 45 °C

• Lithium battery: 3.635V, 3283mAh

• Detachable surround speaker playtime: up to 10 Hours (may vary according to content type and volume level)

HDMI specification

• HDMI video input: 3
• HDMI video output (with Enhanced Audio Return Channel, eARC): 1
• HDMI HDCP version: 2.3
• HDR pass through: HDR10, Dolby Vision

Audio specification

• Frequency response: 33Hz – 20kHz (-6dB)
• Audio inputs: 1 Optical, Bluetooth, USB (USB playback is available in US version. For other versions, USB is for Service only.)

USB specification

• USB port: Type A
• USB rating: 5V DC, 0.5A
• Supporting file formats: mp3
• MP3 codec: MPEG 1 Layer 2/3, MPEG 2 Layer 3, MPEG 2.5 Layer 3
• MP3 sampling rate: 16 – 48 kHz
• MP3 bitrate: 80 – 320 kpbs

Wireless specification

• Bluetooth version: 5.0
• Bluetooth profile: A2DP 1.2, AVRCP 1.5
• Bluetooth transmitter frequency range: 2400 MHz – 2483.5 MHz
• Bluetooth transmitter power: <15 dBm (EIRP)
• Wi-Fi network: IEEE 802.11 a/b/g/n/ac/ax (2.4GHz/5GHz)
• 2.4G Wi-Fi transmitter frequency range: 2412 – 2472 MHz (2.4 GHz ISM Band, USA 11 Channels, Europe and others 13 Channels)
• 2.4G Wi-Fi transmitter power: <20 dBm (EIRP)
• 5G Wi-Fi transmitter frequency range: 5.15 – 5.35GHz, 5.470 – 5.725GHz, 5.725 – 5.825GHz
• 5G Wi-Fi transmitter power: 5.15 – 5.25GHz <23dBm, 5.25 – 5.35GHz & 5.470 – 5.725GHz <20dBm, 5.725 – 5.825GHz <14dBm (EIRP)
• 2.4G wireless transmitter frequency range: 2406 – 2474 MHz
• 2.4G wireless transmitter power: <10 dBm (EIRP)

Dimensions

• Total soundbar dimensions (W x H x D): 1194 x 56 x 125 mm / 47” x 2.2” x 4.9”
• Main soundbar dimensions (W x H x D): 884 x 56 x 125 mm / 34.8” x 2.2” x 4.9”
• Detachable surround speaker dimensions (each) (W x H x D): 155 x 56 x 125 mm / 6.1” x 2.2” x 4.9”
• Subwoofer dimensions (W x H x D): 305 x 440.4 x 305 mm / 12” x 17.3” x 12”
• Soundbar weight: 3.72 kg / 8.2 lbs
• Detachable surround speaker weight (each): 0.7 kg / 1.55 lbs
• Subwoofer weight: 10 kg / 22 lbs
• Packaging dimensions (W x H x D): 1000 x 375 x 475 mm / 39.4” x 14.8” x 18.7”
• Packaging Weight: 19.4 kg / 42.7 lbs

1. Information on power consumption
   This equipment complies with European Commission Regulation (EC) No 1275/2008 and (EU) No 801/2013.
   • Off: N/A
   • Standby (when all wireless connections are deactivated): < 0.5 W
   • Networked standby for Soundbar: < 2.0 W

2. The period of time after which the power management function switches the equipment automatically into:
   Off| N/A|
   ---|---|---
   Standby| When all wired ports are disconnected and all wireless network connections are deactivated| Switched to standby mode after 10 minutes.
   Networked standby| When any wireless network connection is activated| Switched to networked standby mode after 10 minutes of inactivity in operational mode

3. If this equipment has the wireless network connections:
   How to activate wireless network connections:
   • Set up the equipment properly;
   • Switch into wireless mode (Bluetooth, Chromecast built-in™, AirPlay 2 casting audio, Alexa Multi-Room Music & etc);
   • Connect with energy using products (e.g. players/ game consoles/ STB (Set- Top Boxes)/ phones/ tablets /PCs).
   How to deactivate wireless network connections:
   • Press and hold on the remote control for more than 5 seconds firstly;
   • Then long press on the remote control for more than 5 seconds.

FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons.
Use Restriction: This device is restricted to indoor use when operating in the 5150 to 5350 MHz frequency range in following countries:

| AT| BE| BG| HR| CY| CZ| DK
---|---|---|---|---|---|---|---
EE| Fl| FR| DE| EL| HU| IE
IT| LV| LT| LU| MT| NL| PL
PT| RO| SK| SI| ES| SE| UK

Belgium (BE), Greece (EL), Lithuania (LT), Portugal (PT), Bulgaria (BG), Spain (ES), Luxembourg (LU), Romania (RO), Czech Republic (CZ), France (FR), Hungary (HU), Slovenia (SI), Denmark (DK), Croatia (HR), Malta (MT), Slovakia (SK), Germany (DE), Italy (IT), Netherlands (NL), Finland (FI), Estonia (EE), Cyprus (CY), Austria (AT), Sweden (SE), Ireland (IE), Latvia (LV), Poland (PL), United Kingdom (UK) and Northern Ireland (UK (NI)).
This product contains open source software licensed under GPL. For your convenience, the source code and relevant build instruction are
also available at https://harman- webpages.s3.amazonaws.com/JBL_BAR_Gen3_package_license_list.htm
Please feel free to contact us at: Harman Deutschland GmbH
ATT: Open Source, Gregor Krapf-Gunther, Parkring 3
85748 Garching bei Munchen, Germany
or_OpenSourceSupport@Harman.com_if you have additional question regarding the open source software in the product.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by HARMAN International Industries, Incorporated is under license. Other trademarks and trade names are those of their respective owners.
The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Wi-Fi CERTIFIED 6™ and the Wi-Fi CERTIFIED 6™ Logo are trademarks of Wi-Fi Alliance®.
Dolby, Dolby Vision, Dolby Atmos, and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation. Manufactured under license from Dolby Laboratories. Confidential unpublished works. Copyright © 2012–2021 Dolby Laboratories. All rights reserved.
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS, Inc. DTS, DTS:X, and the DTS:X logo are registered trademarks or trademarks of DTS,
Inc. in the United States and other countries. © 2021 DTS, Inc. ALL RIGHTS RESERVED.
Google, Android, Google Play and Chromecast built-in are trademarks of Google LLC.
Use of the Works with Apple badge means that an accessory has been designed to work specifically with the technology identified in the badge and has been certified by the developer to meet Apple performance standards. Apple, and AirPlay are trademarks of Apple Inc., registered in the U.S. and other countries.
To control this AirPlay 2–enabled speaker, iOS 13.4 or later is required.
Amazon, Alexa, and all related marks are trademarks of Amazon.com, Inc. or its affiliates.
Use your phone, tablet or computer as a remote control for Spotify. Go to spotify.com/connect to learn how.
The Spotify Software is subject to third party licenses found here: https://www.spotify.com/connect/third-party-licenses.

** Safety Instruction and Warranty Card
PRODUCT REGISTRATION
https://register.jbl.com/?utm_source=WQR
registerjbl.com
SIGN UP & STAY TUNED**
Register your product
Product registration may not be available for all countrieshttps://www.jbl.com/warrantyandsafetybooks
Download the full warranty Card and safety information and other helpful Information from our website: www.jbl.com/warrantyandsatetybooks

IMPORTANT SAFETY INSTRUCTIONS
For all products:

1. Read these instructions.
2. Keep these instrucUorr.
3. Heed all warnings. 4
4. follow all instructions.
5. Otan only with a dry doth.
6. Do not block any nictitation openings. Install this apparatus in accordance with the manufaeturees instructions
7. Do DX Imtal Ifibapparatus near any heats suds as radiators. heat registers, stows of other apparatus (inducing *mottling that produce heat.
8. Do not defeat the safety purpose oldie polarlted or groording type plug. A polarized plug has tsko blades with one wader than the other. A grounding-type plug has two blades and added grounding prong. The Mite blade of the third prong is provided for yew safety. Nice provided plug does not ht into rig outlet, consult an electrician for replacement Of the obsolete outlet.
9. Protect the power cord from berm walked on or Olrichtd, Parlirolarly at pugs, tonveritne receptacles and the point where they eon bon the apparatus.
10. Use only altattnerst tractessones specified by the manufature.
11. Use oat, with the cart. stand ttipod. bracket or table spitted by the atanubetwer or sold with the apparatus. Mnaartb used use cabal when moving the cart/appatalus combination to mad Inyury form top over.
12. Unplug this apperatus during lightings storms or when unused for long periods of time.
13. Refer all serviching to estalived serve personnel. Servicing is remwed when the ammtabis has been damaged in any way, such as when the power-supply cord or plug is demapd, liquid has been spilled or objets have fallen into the apparaturs, or the apparatus has been exposed to rain or moisture, does not operate normally or has been dropped.
14. To disconnect this apparatus horn the AC maim completely, disconnect the power – supply cord plug from the AC receptacle
15. The mains plug of the power-supply cord shall remain readly operable.
16. This apparatus is intended to be used only with the power supply and:or charging cable provided by the manufactured.

The following Instructions may not apply to waterproof devices. Refer to your device user manual or quick start guide for more waterproof instruction if any.

• Do not use this apparatus near water
• Do not expose this apparatus to dripping or splashing, and ensure that no objects filed with liquids, suds as vases, are placed on the apparatus.

WARNING: TO REDUCE THE RISK OF FEE OR ELECTRIC SHOOK DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN.

THIS SYMBOL ON THE PRODUCT MEANS THERE IS UNINSUL ATM, DANGEROUS VOLTAGE WITHIN THE PRODUCT ENCLOSURE THAT MAY PRESENT A RISK OF ELECTRICAL SHOCK.
ATHIS SYMBOL ON THE PRODUCT MEANS THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THIS GUIDE.
CAUTION FCC AND IC STATEMENT FOR USERS (USA AND CANADA ONLY)
This device complies with part 15 of the FCC Rules. Operation is subject to the flowings two conditions: (This device may not cause harmful interference,and (2) this device mug accept any interference received, including interference that may cause undesired operation.
CAN ICES-3(8)/NM6318)
FCC SDOC SUPPLIER’S DECLARATION OF CONFORMITY
HARMAN International hereby declares that this equipment is 01 corm:dunce with the FCC Part 15 Support B.
The dedication of conformity may be consulted in the support section of our Web site, accessible from www.jbl.com
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part I5 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation Thn equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications However, there is no guarantee that interference will not occur in a  particular installation. If this equipment does cause harmful interference to radio or televisition reception, which can be determined by tinning the equipment off on, the user is encouraged to try to correct the Interference by one or -‘ore of the following measures.

• Reorient or relocate the receiving antenna.
• In crease the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different form that to which the recevers is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes a modifwelom not eroressly approved by HARMAN could rod the Uses authority to operate the equipment
For Products That Transmit RF Energy
(I) FCC AND IC INFOILMATION FOR USERS
This device complies with Part 15 of the FCC rules and Industry Canada license-exempt Pa standard(s). Operation is subject to the following two conditions: (1) device may not cause harmful interference; and (2) this device must accept any interference received. inducting interference that may cause undesired operation.
(ii)FCC/IC Radiation Exposure Statement
This equipment complies with FCC and ISED radiation exposure limits set forth for an uncontrold environment
In use this equipment has to subject to F(CTIC SAR (Specific Absorption Rate) exposure lest this equipment is designed to meet the requirements for exposure to radio waves established by the FCC and MD. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue The highest SAR value reported under this standard during product certification for use when properly worn on the body or on the head, with no separation. To meet RF exposure guidelines and reduce exposure to RF energy during the operation. this equipment should be positioned at least this distance away from the body at the head.
For radio equipment operates in 5150-5850MHz
FCC and IC Caution:
High power radars are allocated as primary uses of the 5.15 to 5.35 Gig and 5.65 to 5 856Hz bands. These radar stations can cause interference with and/or damage to LE USN 11 arise Erem pt local Area Network) dances. No onfiginabon controls are provided for this wireless equipment allowing any change in the frequency of operations outside the FCC grant of authorization for US operation according to Part 15.407 of the FCC rules.
IC Caution:
User should also be adored that.
(i) The dente for operation in the band S150- 525014Ht is only for indoor use to reduce the potential for harmful interference to to-channel mobile satellite systems; (III the maximum antenna gain permitted for times in the bands 5250. 5350 MHz and 5.170: 5725 MHz shall comply with the ti.rp. limit and
(ii)The maximum antenna gain permitted for devices in the band 5715 5825 MHz shall comply with the ex r p. limns specified for point to-point and non point-10.point operation as appropriate.
Use Restriction Attention in European Union, operation is limited to indoor use within the band 5150-5350 MHz.
Correct disposal of this product (Waste Electrical & Electronic Equipment)
This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product. contact your Focal municipality, disposal service, or the shop where you bought this product.
This product is RoHS compliant.
This product is in compliance with Directive /DI 1/65fEU, and its amendments, on the restriction of the use of certain hazardous substances in electrical and electronic equipment.
REACH
REACH (Regulation No 1907006) addresses the production and use of chemical substances and their potential impacts on human health and the environment Affide 33(1) of REACH Regulation requires suppliers to inform the recipients if an article contains more than 0 1 % (per weight per article) of any substance(%) on Mt Substances of Very High Concern (SUFIC’) Candidate lit (‘REACH candidate Intl. This product contains the substance -lead (AS. No. 7439-92:1) in a concentration of more than 0.1% per weight.
At the time of release of this product, except for the kid substance, no other substances of REACH candidate list are contained in a concentration of more than 0.1% per weight in this product.
Note: On lune. 17,1018, lead was added to the REACH candidate list. The inclusion of lead In the REACH candidate Int does not mean that lead containing materials pose an immediate risk or results in a restriction of permissibility of its use.
For devices with headphone jacks
WARNINGS/CAUTIONS
Do NOT use the headphones at a high volume for any extended period.
– To avoid hearing damage, use your headphones at a comfortable, moderate volume level.
– Turn the volume down on your device before placing the headphones on your ears, then turn the volume up gradually until you reach a comfortable listening level
For Products That Include Batteries
Instructions for Users on Removal Recycling and Disposal of Used Batteries
** To remove the batteries from your equipment or remote control, reverse the procedure described in the owner’s manual for inserting batteries. For products with a built-in battery that lasts for the lifetime of the product, removal may not be possible for the user In this case, recycling or recovery centers handle the dismantling of the product and the removal of the battery, if, for any reason, it becomes necessary to replace such a battery, this procedure must be performed by authorized service centers. In the European Union and other locations, it is illegal to dispose of any battery with household trash. All batteries must be disposed of In an environmentally sound manner Contact your local waste-management officials for information regarding the environmentally sound collection. recycling and disposal of used batteries. WARNING: Danger of explosion if battery is Incorrectly replaced To reduce risk of fire, explosion or leakage of flammable liquid/gas, don’t disassemble, crush, puncture, short external contacts, expose to temperature above 60’C (140-T), sunshine or like, expose to extremely low air pressure or dispose of in fire or water Replace only with specified batteries. The symbol indicating ‘separate colktion’ for all batteries and accumulators shall be the crossed-out wheeled bin shown below.
WARNING – For Products Contain Coin/Button Cell Batteries**
DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD This product contains a corrubutton all battery. If the coin/button cell battery is swallowed, it can cause severe Internal burns in just 2 hours and can lead to death. keep new and used batteries away from child/m.1f the battery compartment does not dose securely, stop using the product and keep it away from children_ If you think batteries might have been swallowed or placed inside any part of the body. seek immediate medical attention
For All Products with Wireless Operation:
HARMAN International hereby declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/th. The declaration of conformity may be consulted In the support section of our Web site, accessible from www.jbl.com.

HARMAN International Industries, Incorporated All rights reserved.
JBl is a trademark of HARMAN International Industries, Incorporated, registered in the United States and/of other countnes.
Features, specifirahom and appearance are subject to change without notice.

****www.jbl.com

HARMAN
HARMAN IntematIonol Indust:
Incorpwated 8500 Balboa Boulevard.
Northridge. CA 91329
USA 516.255.4545 (USA only)

Harman International Industries, Incorporated 8500 Balboa Blvd.
Northridge, CA 91329
USA
EU DECLARATION OF CONFORMITY
1. Model No., trademark:
BAR 1000, BAR 1000 SURROUND, BAR 1000 SUB JBL
2. Name and address of the manufacturer’s authorised representative:
Harman International Industries, Incorporated
EMEA Liaison Office, Danzigerkade 16G,1013 AP Amsterdam, The Netherlands
3. This declaration of conformity is issued under the sole responsibility of the manufacturer:
Harman International Industries, Incorporated
8500 Balboa Blvd, Northridge, CA 91329, UNITED STATES
4. Object of the declaration: Multi-Channel Soundbar with wireless subwoofer
5. The object of the declaration described above is in conformity with the relevant Union harmonisation legislation directive and Other Union harmonisation legislation where applicable: RED – 2014/53/EU, ERP – 2009/125/EC,
RoHS – (EU) 2015/863 amending Annex ll to 2011/65/EU,
6. References to the relevant harmonised standards used or references to the other technical spec-ifications in relation to which conformity is declared. References must be listed with their identification number and version and, where applicable, date of issue:
EN 55032:2015, EN 55032:2015/A11:2020, EN 55035:2017, EN 55035:2017/A11:2020
EN IEC 62311:2020, EN 62368-1:2014+A11:2017,EN 300 440V2.2.1,ETSI EN 301 489-1 V2.2.3, ETSI EN 301 489-17 V3.2.4
EN 61000-3-3:2013/A2:2021, EN IEC 61000-3-2:2019/A1:2021,EN 300 328 V2.2.2
EN 301 893 V2.1.1 (EC) No 1275/2008 & (EU) No 801/2013.EN 50564:2011.EN IEC 63000:2018 7.
Where applicable, the notified body … (name, number) … performed … (description of intervention) And issued the EU-type examination certificate: …
8. Where applicable, description of accessories and components, including software, which allow the radio equipment to operate as intended and covered by the EU declaration of conformity: EPS: Model:
9. Additional information:

(Signature):…………….
(Name. Function):…………….
Signed for and on behalf of:……….
(Place and date of issue):……………….

Clarice Chen Sr. Manager. Product Compliance & Sustainability
Harman International Industries
Incorporated Shenzhen, China. 2022-09-05
No. HA-20220905-004

References

• Amazon.com
• The domain name chemic.al is for sale
• Welcome to nginx!
• Patents - DTS
• Spotify - Connect
• Official JBL Store - Speakers, Headphones, and More!
• Official JBL Store - Speakers, Headphones, and More!
• Official JBL Store - Speakers, Headphones, and More!
• harman-webpages.s3.amazonaws.com/JBL_BAR_Gen3_package_license_list.htm
• Third Party Licenses | Spotify for Developers

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>