ASD-LFMDR-10D16CC-NK LED Double Ring Flushmount Instruction Manual

ASD-LFMDR-10D16CC-NK LED Double Ring Flushmount

LED DOUBLE RING FLUSHMOUNT

DESIGN & OPTIONS

LED DOUBLE RING FLUSHMOUNT has a modern, multipurpose design and a stylish look with efficient lighting. It also possesses smooth dimming capabilities ranging from 10% to 100% with modern LED dimmers. With the color selectable option, you can change the color temperature from 3,000K, to 4,000K, to 5,000K with a simple switch. The 120° beam angle grants you smooth and even lighting. It comes in 10″, 12″, 14″, 16″ and 18″ with either a BRONZE or BRUSHED NICKEL finish.Models with a built-in microwave motion sensor automatically turn off in the absence of motion and can be programmed via dip switch. Models with a built-in battery back-up provide 90 minutes of power in case of emergency.

INSTALLATION

Installation is quick and easy: just connect the wires and fix the fixture to the outlet box. Screws, wire nuts and all installation accessories are provided. Refer to install instructions for detailed steps.

APPLICATION

The LED DOUBLE RING FLUSHMOUNT provides bright, yet smooth lighting for your family room, bedroom, hallway, corridor, or any other common area in your living space. It can be used as an additional light to an already existing ceiling light as well. This fixture is also Damp Locations rated.

ENERGY SAVING & EFFICIENCY

With a lifespan of 50,000 hours, these fixtures are made to last decades under normal operation! This fixture can cut your electric bill by up to 80% instantly and will save you a significant amount of money in its lifetime.

CERTIFICATION & WARRANTY

Buy with confidence: ASD provides a 5-year limited warranty along with ЕТL certification to guarantee top quality products and safety! Energy Star classification allow participation in rebates; please check the rebate programs available in your state.

PRODUCT SPECIFICATIONS

BUILT-IN MOTION SENSOR INFORMATION

Specifications Model: HD401S 1

• Operating voltage: 120-277 V
• Switching capacity : Max. 200W (Control gear) Max. 400W (Incandescent lamp)
• Standby power: < 1W
• Detection area : 10 %/50 %/75 %/100 %
• Hold-time: 5 s/90 s/5 min/15 min
• Daylight threshold: 2 Lx (0.2 Fc)/10 Lx (0.9 Fc)/50 Lx (4.7 Fc)/Disable
• Microwave frequency: 5.8 GHz ± 75 MHz
• Microwave power: < 0.3 mW
• Interfaces: 4-pole pluggable clamp terminal (L,N,N,L’) for 1.5 mm 2 cable
• Mounting height: Max. 39.4 ft (11.9 m)
• Detection range: Max. 52.5 x 39.4 ft (15.8 x 11.9 m) (ceiling mounted)
• Operating temperature: -4 +158°F (-20 +70°C) IP rating IP20
• Size: 3.2 x 1.4 x 0.9 inch

PACKAGE CONTENTS

DEFAULT SETTING

Detection area:
Detection area means detection coverage. lt can be adjusted by combining DIP swithches for specific application.

Hold time:
Hold-time is the time period the light will be ON after the last detection.

Daylight threshold:
Daylight sensor priors to motion sensor. Set threshold for specific needs. If set on “Disable” only the motion sensor will work.

BUILT-IN BATTERY BACK-UP INFORMATION

1. Indicator light is ON: Battery back-up fully charged and device is using circuit power.
2. Indicator light is Blinking: Battery back-up recharging and device is using circuit power.
3. Indicator light is OFF: Device is using battery back-up power.
4. In order to test the battery back-up press the test switch one time. To turn off the emergency power state press test switch one more time.

INSTALLATION GUIDE

IMPORTANT SAFETY INFORMATION

Please read all the instructions below before installation.

• Make sure that the supply voltage corresponds to the rated product voltage.
• The product must be installed by a qualified electrician in accordance with the
• National Electrical Code and corresponding local codes.
• If the product is damaged, do not use it.

Specifications

• Input voltage: 100-277 V 50/60 Hz
• AC Input current: 110 mA max.
• AC Input power rating: 5.0W max.
• Output current and voltage: 200 mA 20-36 Vdc 360 mA 20-36 Vdc
• Output power: 6W 12W
• Lumens: 400 lm 800 lm
• Emergency time: min 90 minutes
• Warranty: 5 Years
• Indicator light: Illuminated test switch
• Battery: Li-ion battery – 11.1 V/2200 mAh
• Battery charging current: 440 mA
• Charging time: 8 Hours
• Temperature rating (Ambient): 32°F to 113°F (0°C to 45°C)

WARNING
RISK OF PERSONAL INJURY – READ and follow all WARNINGS and installation instructions. Keep or give to the owner for future reference. Risk of cuts: Wear gloves to prevent cuts or abrasions when removing from carton, handling, installing, and maintaining this product. Risk of electric shock: This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Risk of Fire: Minimum 194°F supply conductors. Consult a qualified electrician to ensure correct branch circuit conductor. ASD® assumes no responsibility for claims arising out of improper or careless Installation or handling of this product.

ELECTRICAL SCHEMATIC DIAGRAM

INSTALLATION STEPS

1. Unscrew three cap nuts counter-clockwise, remove the metal ring and the lens.
2. Attach two screws to the outlet box. Connect the wires: Black to Black, White to White, Ground to Ground. Carefully tuck all the wires back into the outlet box. 2.b. In fixtures with Emergency battery connect the LED Emergency controller to the battery back-up.
3. Place the fixture pan over the outlet box and feed fixture screws through keyhole slots. Rotate the fixture pan clockwise until screws lock into the narrow end of the keyhole slots and tighten screws firmly. Choose either 3,000K, 4,000K or 5,000K with a simple switch. Secure the lens and the metal ring to the fixture pan using three cap nuts.

ORDERING INFORMATION

E-mail: orders@asd-lighting.com Web site: www.asd-lighting.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>