ikan PT4900S-PTZ Profesional 19 Inch High Bright PTZ Compatible Teleprompter w/ 3G-SDI User Guide
- June 9, 2024
- ikan
Table of Contents
- ikan PT4900S-PTZ Profesional 19 Inch High Bright PTZ Compatible
- OVERVIEW
- What’s Included
- Teleprompter Assembly Setup
- Monitor Ports
- Monitor Menu Settings
- How to set up the FLIP button feature
- Specifications for PT4900S-PTZ
- Optional Accessories
- What’s Included
- Assembly Steps
- Specifications
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ikan PT4900S-PTZ Profesional 19 Inch High Bright PTZ Compatible
Teleprompter w/ 3G-SDI
OVERVIEW
The 19” PTZ Teleprompter from Ikan is a professional solution for teleprompting with PTZ cameras. The package provides an extra-wide hood assembly to allow considerable movement of the camera within the wide beam splitter glass. The PTZ Teleprompter features a 19” 1000 cd/m² monitor, 70/30 20”-wide beamsplitter glass, and a 25’ reading range. The teleprompter is designed for use with a wide range of PTZ cameras, as the wide beamsplitter provides for a wide amount of left-right panning. The teleprompter includes a base system that can be easily shifted forward and backward, which enables mounting the camera to the prompter without requiring counterweights.
Please note that the PTZ4900S-PTZ includes parts to build two types of teleprompter systems, a standard 19” Teleprompter that is compatible with various types of mirrorless and broadcast cameras, and a 19” PTZ teleprompter that is compatible with a wide range of PTZ cameras. This Quick Start Guide will show you how to set up the 19” Teleprompter for PTZ cameras. For instructions on how to set up the PT4900 for broadcast or mirrorless cameras, please refer to the PT4900 Quick Start Guide on our website.
What’s Included
Teleprompter Assembly Setup
Step 1
Place the Hood Attachment Frame over the Glass Holder. Then place the glass
against the Glass Holder. Make sure the screws pass through the holes on both
the Hood Attachment Frame and the Glass Holder.
Step 2
Secure the Glass Holder by fastening the knurled nuts to the screws as
pictured below.
Step 3
Remove the monitor mounts from the teleprompter base using the included larger
4mm hex key to loosen from the 15mm rods.
Step 4
Put the washers on before tightening the screws. The washers and 4 additional
screws are inside a bag on the bottom foam.
Step 5
After the monitor mounts are attached, adjust the 15mm rods to accommodate the
monitor. Leave about 1 inch of room for the teleprompter bracket. Make sure
the 15mm rods go through both set of monitor mounts. Please ensure that all
screws are properly tightened after inserting the monitor. SAFETY NOTE Make
sure to leave at least 2 inches of the rods inside the teleprompter base.
Step 6
While sliding the teleprompter bracket into the slot of the Glass Frame Holder
Bracket, pull on the red knob to allow the bracket to fully slide in.
Step 7
Once the bracket is in place, tighten the side screw to lock it in place.
Double-check and make sure all the screws are tightened with the included hex
keys.
Step 8
Fold the flaps of the Hood alongside the edges of the Hood Attachment Frame.
The flaps of the Hood are magnetic so they will automatically attach. Connect
the bottom part of the hood by attaching the magnetic flap to the glass frame
holder. Connect the velcro straps to the sides of the hood.
Step 9-A: Connecting the PTZ Riser to the Ikan OTTICA
To connect the PTZ Camera Riser to the Ikan OTTICA camera, fasten the ¼-20
screw on the PTZ Riser Plate to the thread on the bottom of the OTTICA camera.
Step 9-B: Connecting the PTZ Riser to other PTZ Cameras
To connect the PTZ Camera Riser to the other PTZ cameras, Remove the plate on
top of the PTZ Riser by unfastening the four screws on the surface of the
plate. Once the plate has been removed, fasten the ¼-20 screw on the PTZ Riser
Plate to the thread on the bottom of the PTZ camera.
Step 10
Set the PTZ camera inside the hood by aligning the screws on the riser plate
to the slot on the Base. Once the screws are aligned, Slide the riser plate
into the Base.
Step 11
To prevent light from leaking through the hood, seal both zippers down, and
attach the velcro straps along the back and sides of the hood. Connect the
cables to the back of your PTZ camera by putting them through the slot on the
back of the PTZ Hood. Once your cables are connected, tighten the drawstring
on the back of the PTZ Hood.
Step 12
Mount your own tripod plate to the bottom plate by aligning the 1/4-20 and/or
3/8-16 screws and fastening them to the Bottom Plate. It is recommended that
you connect your tripod plate to the front of the Bottom Plate so that you can
balance your teleprompter easier. Once your tripod plate is connected to the
Bottom Plate, mount the tripod plate to your tripod head.
Step 13
In order to properly balance the teleprompter, loosen the 4 screws on the
bottom plate and slide the entire teleprompter system back or forward until
the center of gravity has been determined. Once the center of gravity has been
determined, tighten the thumb screws to keep the base from sliding.
Step 14
To secure your teleprompter system, insert the included headless screws into
the threads behind and in front of the Base.
Step 15
The headless screws should be inserted to the threads as pictured below
.
Monitor Ports
- 3G-SDI – Serial Digital Interface Connection
- VGA – Video Graphics Array DE15 Connection
- HDMI – High-Definition Multimedia Interface Input Connection
- Power Port – 12-24v Input
- HDMI – Switch HDMI input
- VGA – Switch to VGA input
- SDI – Switch to 3G-SDI input
- Flip – Toggle image flip (Can be set to horizontal, vertical, or both via the menu)
- Up Arrow – Toggle up to adjust the setting
- Menu – Access to monitor settings
- Down Arrow – Toggle down to adjust the setting
Monitor Menu Settings
Video Config
- Contrast (White Level)
- Brightness (Black Level)
- Tint (Chroma Hue)
- Chroma (Chroma Saturation)
- Sharpness (Detail)
- RGB Setup – Manually configure RGB Return
System Config
- Menu Duration – Set the duration of how long the menu stays on screen
- Video Ratio – Set screen aspect ratio 16:9 or 4:3 (4:3 is native resolution, 16:9 will create black bars)
- Flip-H – Assign a toggle button to flip the image horizontally
- Flip-V – Assign a toggle button to flip the image vertically
- Reset – Factory reset Return
PC Setup (Only available for VGA)
- H-Position – Adjust the horizontal position
- V-Position – Adjust the vertical position
- Auto – Monitor automatically adjust position Return
- Exit
How to set up the FLIP button feature
- Press MENU button
- Navigate to SYSTEM CONFIG.
- Navigate to FLIP-V or FLIP-H
- Change FLIP-V and/or FLIP-H to “ON”
- Exit MENU
- The FLIP button should now be activated and can be pressed to mirror the image Horizontally or Vertically
- When FLIP-H is ON, the image will flip Horizontally
- When FLIP-V is ON, the image will flip Vertically
- If both are ON, the FLIP button will toggle both Horizontal and Vertical flip
Watch our VIDEO TUTORIAL on how to assemble Ikan Professional Teleprompters:
https://youtube.com/playlist?list=PLcjaK5n9Y8ctrbYS3t2g4nyx2uADOXjuF.
Specifications for PT4900S-PTZ
TELEPROMPTER SPECIFICATIONS
Riser Plate Height
| Low: 2.06 in./52.5mm | Medium: 3.74 in./95mm| High:
5.31 in./135mm | DSLR: 6.29 in./160mm
---|---
Length of Rods| 15mm x 400mm
Build Material| Chassis: Anodized Aluminum | Rods: Carbon Fiber
Reading Range| 25 ft. / 7.62 m
Beamsplitter Ratio| 70/30
Beamsplitter Shape| Rectangular
Beamsplitter Material| Glass
Tripod Mounts| 11 x 1/4 in. -20 Female | 9 x 3/8 in. -16 Female
Product Weight w/ Low Plate| 22.70 lbs.
Product Weight w/ Medium Plate| 23.10 lbs.
Product Weight w/ High Plate| 23.23 lbs.
Product Weight w/ DSLR Plate| 22.60 lbs.
Height of Teleprompter| 16 in./ 406mm
Angle of Glass Frame Holder| 50°
Material of Hood| Polyester Canvas
Material of Riser Plates| Aluminum
Material of Glass Frame Holder| Aluminum
MONITOR SPECS
Aspect Ratio | 4:3 |
---|---|
Maximum Brightness | 1000 cd/m2 |
Screen Size (Diagonal) | 18.5 in. |
Mount | VESA 100mm |
Video Inputs | 3G-SDI, HDMI, VGA |
Input Voltage | DC 12v / 4A |
Power Consumption | 21W |
Product Weight | 6 lbs. |
Product Dimensions | 17 in. x 15 in. x 1 in. |
Native Resolution | 1280 x 1024 |
Viewing Angle | 160° (H) / 170° (V) |
Build Material | Aluminum Chassis |
Image Flip | Horizontal: Yes |
Optional Accessories
- PT4900-GM Replacement Glass for PT4900
- PT19W-TALLY 19” Widescreen Talent Monitor w/ Tally Add-on Kit for PT4900
- PT-PEDAL Teleprompter Foot Control Pedal
- PT-CASE-V2 Rolling Hard Case for PT4900 Teleprompter
Foam Case
- To make your teleprompter more portable, we packed it in reusable, high-quality foam.
- The shape and size of the foam were designed to fit into Ikan’s PT-CASE-V2.
19″ High Bright Talent Teleprompter Add-On Kit (SDI)
What’s Included
- 1 x SDI Teleprompter Monitor w/ Aluminum Chassis
- 1 x Power Adapter with Cable
- 1 x VESA Monitor Mount
- 1 x 15mm Rod Adapter
- 1 x Mounting Knob
- 4 x 10mm Screws
- 4 x 15mm Screws
- 2 x Large Screws
- 4 x Riser Washers
- 1 x Adjustable Plate
Assembly Steps
Setting Up the Talent Monitor
Using the shorter 4 x 10mm Screws, attach the VESA Monitor Mount. Make sure
that the long end of the VESA Monitor Mount is pointing in the direction of
the power button like in the image above. Use the Mounting Knob to tighten the
15mm Rod Adapter to the VESA Monitor Mount.
Setting Up the Teleprompter Monitor (Monitor from the PT4900-SDI)
If the mounting brackets were previously installed on the teleprompter
monitor, remove those screws. Using the longer 4 x 15mm Screws and 4 x Riser
Washers attach the mounting brackets with the washers between the bracket and
monitor like in the image below.
Attaching the Talent Monitor
After both the talent monitor and teleprompter monitor are set up, slide the
talent monitor onto the PT4900-SDI.
WARNING
We recommend at least 1 inch of the rod should be left inside the teleprompter
base.
Specifications
PT19-SDI-TM
19” High-Bright Teleprompter Monitor
Aspect Ratio | 4:3 |
---|---|
Brightness | 1000 cd/m2 |
Screen Size | 19” |
Video Inputs | SDI, HDMI, VGA |
Input Voltage | DC 12v / 4A |
Power Consumption | 10 w |
Product Weight | 12 lbs |
Product Dimensions | 17” x 15” x 1” |
Native Resolution | 1280 x 1024 |
Shipping Weight | 14 lbs |
Shipping Dimensions | 24” x 20” x 4” |
Viewing Angle | 160° (H) / 170° (V) |
UPC | 847983033218 |
Build Material | Aluminum Chassis |
Supported Video Signals
HDMI
- 720x480i & 720x480p @ 59.94, 60 Hz
- 720x576i & 720x576p @ 50 Hz
- 1280x720p @ 50, 59.94, 60 Hz
- 1920x1080i @ 50, 59.94, 60 Hz
- 1920x1080psf @ 24, 25, 29.97, 30 Hz
- 1920x1080p @ 23.98, 24, 25, 29.97, 30, 50, 59.94, 60 Hz
SDI
- 720x480i @ 59.94, 60 Hz
- 720x576i @ 50 Hz
- 1280x720p @ 50, 60 Hz
- 1920x1080i @ 50, 59.94, 60 Hz
- 1920x1080psf @ 24, 25, 29.97, 30 Hz
- 1920x1080p @ 23.93, 24, 25, 29.97, 30, 50, 59.94, 60 Hz
Optional Accessories
Some other products that work well with this item available from Ikan include:
PT4900-SDI
Professional 19″ High Bright Beam Splitter Teleprompter with 3G-SDI
Learn More
More dynamic information at the official website:
www.ikancorp.com.
Support
Contact email: support@ikancorp.com.
CONDITIONS OF WARRANTY SERVICE
- Free service for one year from the day of purchase if the problem is caused by manufacturing errors.
- The components and maintenance service fee will be charged if the warranty period is expired.
*Free Service will not be Provided in the Following Situations: (Even if the product is still within the warranty period.)**
- Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company.
- Damage caused by natural disasters, abnormal voltage, environmental factors, etc.
©2022 Ikan International. All rights reserved.
www.ikancorp.com. | 1.713.272.8822 | sales@ikancorp.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>