RS PRO 135-8426 45W Tubular Heater Owner’s Manual
- June 9, 2024
- RS PRO
Table of Contents
RS PRO 135-8426 45W Tubular Heater
FEATURES
- Maximum output power 45W
- Waterproof IP55 for dust and water spray resistance
- Temperature is controlled by selfthermostat
- Capable of heating area 0.5 m2
- Surface mount brackets come as standard for easy installation by wall / floor mounting.
- Easily installation by sliding brackets together and screw into the application then clip the heater.
Product Description
The tubular heater is ideal for use as a greenhouse heater, garage heater, shed heater loft heater or any space that require background heating. It’s supplied pre-fitted with 1 meter of 3 core main cable without a molded plug ready to be installed into a fused spur.
- Please be noted that the temperature is controlled by self-thermostat which installed inside the product. The thermostat controls product temperature, once the temperature reach 65°C, the thermostat will activate. Once the temperature lower down, the heating tube will continue to work. The very important point is that the thermostat cannot control the air temperature, only for product inner temperature.
General Specifications
| Overall Dimension | 31 x 9.5 x 9.5 cm |
|---|---|
| Tube Material | Steel |
| Bracket Material | PC |
| Finish | Powder coating white color |
| Mounting Accessories | 2 x Mounting brackets for wall, floor mounting |
| Plug | Excluded |
| Cable | Included, 1M length |
Electrical Specifications
| Power Supply | 240V, 50Hz |
|---|---|
| Wattage | 45W |
| Water Prove IP rating | IP55 |
| Heating Area | 0.5 m2 |
Additional Information
| Custom Tariff Number | 85168000 |
|---|
Approvals
| Certificate | CE, RoHS, GS |
|---|
Similar Products
| Stock No. | Brand | Product Name |
|---|---|---|
| 1358427 | RS PRO | Steel Tubular Heater 80W |
| 1358428 | RS PRO | Steel Tubular Heater 135W |
| 1358429 | RS PRO | Steel Tubular Heater 240W |
BEFORE ATTEMPING TO INSTALL UNITS，ENSURE POWER IS OFF，AND PLEASE PAY ATTENTION TO FOLLOWING SETPS.
MOUNTING POSITION
The electronical heater should be mounted on the wall as the figure below
- Screw the two bottom halves of the bracket to the wall, place tubular heater on brackets.
- Fasten top brackets over tube.
Installation Direction
-
This heater must be installed in a horizontal position only. Please do not mount it vertically.
Before installation, please check you have all the parts listed below.
4 x Small screws, 4 x Large screws, 4 x Expansion screws, 2 x Wall attachments
1 x Tube heater -
Secure the tube heaters to the wall attachments, and screw in place with small screw.
-
Hold the heater against the wall and mark the position of the fixing holes. If fixing to a studded wall, or a Wooden surface, use the large screw and wall plug. If the wall is hollow, or you are drilling into masonry, using the pilot holes as guide, drill again using a 6.5mm drill bit and insert a wall plug into each hole. Once holes are prepared, mount the tube and secure.
-
Now plug into a mains wall socket. When you switch the wall socket on, the red indicator light will switch on, and your heater is now on. To turn your heater off, switch the wall socket of, or unplug.
Caution
It is very important that the Tubular Heater is mounted horizontally to a wall at low-level. Any shelving placed above the Tubular Heater must be at distance of at least 300mm. Air should be allowed to freely circulate around the Tubular Heater to avoid overheating.
Customer Support
RS Components – Buy this product from https://uk.rs-online.com/
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>