Knightsbridge WP21CCT Wall Light Instruction Manual

Knightsbridge WP21CCT Wall Light

GENERAL INSTRUCTIONS

These instructions should be read carefully and retained after installation by the end user for future reference and maintenance.
These instructions should be used to aid the installation of the following product: WP21CCT

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the circuit cable, fuse, or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is Class II double insulated
• This product is IP65 rated

INSTALLATION

Note – If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the manufacturer of the sensors that they are compatible with LED luminaires.

• Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable IP rated junction boxes should be used where required
• Remove the front bezel by pulling it on all four sides (see Fig. 1)
• Remove the diffuser by removing the four screws
• Open the hinged LED tray by rotating the wing nut
• Round cable should be used for the mains supply. The use of a flat cable will cause water to ingress into the fitting
• Drill the fixing holes in the rear of the fitting. Mark the location of the fixing holes and drill ensuring not to infringe with any gas/water pipes or electrical cables
• Feed the mains cable through the rubber grommet to retain IP rating and secure it to the surface using the screws provided. Rubber washers or sealant should be applied around the screw heads to prevent water ingress
• Using a small flat head screwdriver, remove the LED driver terminal cover on the primary side
• Connect the luminaire to the mains supply ensuring the correct polarity is observed: L – Live (brown) and N – Neutral (blue)
• Reattach the LED driver terminal cover
• Close the LED tray and fix it in place with the wing nut
• Choose the required colour temperature by means of the DIP switch (see Fig. 3)
• Replace the diffuser and the bezel
• Switch on and check for correct operation

FEATURE

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

• This product contains a light source of energy efficiency class E to Regulation (EU) No. 2019/2015 and (UK) 2021 No. 1095.
• This product contains a LED light source and a control gear which can be replaced by a professional.
• Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not use aggressive cleaning products or solvents which may damage the product.
• Do not use any source of high-pressure washers to maintain or clean this luminaire.
• This product is non-dimmable.
• This product should be dismantled for disposal when it reaches the end of its life. Please see website for dismantling instructions.
• This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities for where facilities exist.

WARRANTY

This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation costs associated with the replacement product. Your statutory rights are not affected.
ML Accessories reserve the right to alter product specification without prior notice.

Supplied By:
(UK) Manufacturer ML Accessories Ltd, Unit E Chiltern Park, Boscombe Road, Dunstable LU5 4LT,
www.mlaccessories.co.uk
(EU) Authorised Representative nnuks Holding GmbH, Niederkasseler Lohweg 18, 40547 Düsseldorf, Germany,
Email : eprel@nnuks.com

References

• ML Accessories

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>